Panasonic TH-98LQ70U / TH-98LQ70W / TH-98LQ70C Service Manual ▷ View online
DIS-11
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-6. Removal of A-Board
■
Attention when replacing A-Board
4. Remove the A-Board. (with shield and Fan)
・
Market Select should be set after exchange of A-Board.
(Regarding Market Select, refer to "MS mode" INF-6. )
■
Caution when replacing A-Board
The shield is not attached to A-Board for repair.
・
When replacing the A-Board, please be sure to restick
Please be sure to remove a shield from A-Board and
a Heat Sheet on the original position.
reuse it.
1. Remove screws and Back Cover following the
instructions on "2-5-1 Removal of Back Cover(BR)".
2. Remove the screws fixing the Terminal Bracket and
A-Board.
instructions on "2-5-1 Removal of Back Cover(BR)".
2. Remove the screws fixing the Terminal Bracket and
A-Board.
3. Disconnect the connectors and the coupler and remove
the screws.
XYN3+F8FJ : 8
[60 ±
[60 ±
20
N・㎝]
Two-tiered TMKK497 are
attached at three positions.
Two-tiered
TMKK510
are attached at six positions.
HEATSINK
±
2mm
±
2mm
※
The tolerances of nine positions are same.
The distortion of Two-tiered HEAT SIheet is within 1mm.
Edge of HEAT Sheet is adjusted on Edge of Metal.
(
(
The tolerance ±2mm)
THEA068N: 4
[60 ±
[60 ±
20
N・㎝]
THEJ036J: 4
[60 ±
[60 ±
20
N・㎝]
DIS-12
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-7. Removal of HX-Board
2-9. Removal of P-Board Main
1. Remove screws and Back Cover following the
1. Remove screws and Back Cover following the
instructions on "2-5-1 Removal of Back Cover(BR)".
instructions on "2-5-1 Removal of Back Cover(BR)".
2. Remove the screws fixing the Terminal Bracket and
2. Disconnect the connectors and the coupler and remove
HX-Board.
the screws and then remove the P-Board Main.
3. Disconnect the connectors and the coupler and remove
the screws and then remove the HX-Board.
the screws and then remove the HX-Board.
■
Caution when replacing P-Board Main
・
When replacing the P-Board Main, please be sure to
restick a Heat Sheet on the original position.
2-8. Removal of Terminal Bracket
1. Remove screws and Back Cover following the
instructions on "2-5-1 Removal of Back Cover(BR)".
2. Remove the screws fixing the Terminal Bracket and
instructions on "2-5-1 Removal of Back Cover(BR)".
2. Remove the screws fixing the Terminal Bracket and
HX-Board and A-Bboard.
3. Remove the Terminal Bracket.
■
Caution when replacing A-Board
・
When replacing the A-Board, please be sure to restick
a Heat Sheet on the original position.
XYN3+F8FJ
: 9
[60 ±
20
N・㎝]
XYN3+F8FJ : 3
[60 ±
[60 ±
20
N・㎝]
TMKK515 is attached at one
position.
※
※
MAIN side only
±1mm
±1mm
THEA068N: 6
[60 ±
[60 ±
20
N・㎝]
THEJ036J: 9
[60 ±
[60 ±
20
N・㎝]
XYN3+F8FJ : 2
[60 ±
[60 ±
20
N・㎝]
THEA068N: 2
[60 ±
[60 ±
20
N・㎝]
Edge of HEAT Sheet is adjusted on Edge of Metal.
(
(
The tolerance ±2mm)
DIS-13
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-10. Removal of Fan (A)
2-12. Removal of P-Board Sub
1. Remove screws and Back Cover following the
1. Remove screws and Back Cover following the
instructions on "2-5-1 Removal of Back Cover(BR)".
instructions on "2-5-2 Removal of Back Cover(BL)".
2. Disconnect the Fan joint connector and remove the
2. Disconnect the connectors and the coupler and remove
screws.
the screws and then remove the P-Board Sub.
3. Remove the Fan Rubber from the Fan.
2-11. Removal of V1-Board
2-13. Removal of F-Board
1. Remove screws and Back Cover following the
1. Remove screws and Back Cover following the
instructions on "2-5-1 Removal of Back Cover(BR)".
instructions on "2-5-2 Removal of Back Cover(BL)".
2. Remove the screws and then remove the V1
2. Disconnect the connectors and the coupler and remove
LED Fixing Metal.
the screws and then remove the F-Board Sub.
3. Remove the V1-Borad and DEC LED Panel.
Disconnect the FFC from the V1-Board.
Disconnect the FFC from the V1-Board.
XYN3+F8FJ
: 6
[60 ±
20
N・㎝]
XYN3+F8FJ
: 9
[60 ±
20
N・㎝]
THEJ039J
: 3
[60 ±
20
N・㎝]
THEL057J
: 2
[60 ±
20
N・㎝]
LED Panel
LED Fixing Metal
V1-Board
DIS-14
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-14. Removal of Inlet Assy
1. Remove screws and Back Cover following the
instructions on "2-5-2 Removal of Back Cover(BL)".
2. Disconnect the connector and remove the screws
instructions on "2-5-2 Removal of Back Cover(BL)".
2. Disconnect the connector and remove the screws
and then remove the Inlet Assy.
2-15. Removal of FR-Board
2-16. Removal of Fan (FR)
1. Remove screws and Back Cover following the
instructions on "2-5-3 Removal of Back Cover(TR)".
instructions on "2-5-3 Removal of Back Cover(TR)".
1. Remove screws and Back Cover following the
2. Disconnect the connectors and the coupler and remove
instructions on "2-5-3 Removal of Back Cover(TR)".
the screws and then remove the FR-Board.
2. Disconnect the Fan joint connector and remove the
screws.
3. Remove the Fan Rubber from the Fan.
screws.
3. Remove the Fan Rubber from the Fan.
THEJ036J: 4
[60 ±
[60 ±
20
N・㎝]
XYN3+F8FJ : 6
[60 ±
[60 ±
20
N・㎝]
HEAT
SINK
SINK
±2mm
±2mm
THEJ039J
: 3
[60 ±
20
N・㎝]
Two-tiered TMKK497 are
attached at four positions.
※
The tolerances of four positions are same.
The distortion of Two-tiered HEAT SIheet is within 1mm.
Edge of HEAT Sheet is adjusted on Edge of Metal.
(
(
The tolerance HEAT ±2mm)
Click on the first or last page to see other TH-98LQ70U / TH-98LQ70W / TH-98LQ70C service manuals if exist.