Panasonic TH-98LQ70U / TH-98LQ70W / TH-98LQ70C Service Manual ▷ View online
DIS-7
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-2-5. Type 5
2-2-7. Type 7
■
How to disconnect
■
How to disconnect
1. Disconnect the LVDS cable in the direction of arrow②
1. Disconnect the LVDS cable in the direction of arrow②
while pushing the hook in the direction of arrow①.
while pushing the hook in the direction of arrow①.
■
How to connect
■
How to connect
1. Lock the LVDS securely to push both edge of connector
1. Insert the LVDS cable into the deepest part of insertion
parallel in the direction of black arrow.
directly.
2-2-6. Type 6
■
How to disconnect
1. Disconnect the LVDS cable in the direction of arrow②
while pushing the hook in the direction of arrow①.
■
How to connect
1. Insert the LVDS cable into the deepest part of insertion
directly.
directly.
Hook
Hook
Hook
Hook
Hook
DIS-8
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-3. Flowchart for Disassembly
2-4.
Preparations
2-5.
Removal of Back Cover
2-5-1.
Removal of Back Cover(BR)
2-21.
Removal of Cabinet Block
2-6.
Removal of A-Board
2-21-1. Removal of Front Glass
2-7.
Removal of HX-Board
2-21-2.
Removal of Cabinet
2-8.
Removal of Terminal Bracket
2-22.
Replacement of LCD Module
2-9.
Removal of P-Board Main
2-10.
Removal of Fan (A)
2-11.
Removal of V1-Board
2-5-2.
Removal of Back Cover(BL)
2-12.
Removal of P-Board Sub
2-13.
Removal of F-Board
2-14.
Removal of Inlet Assy
2-5-3.
Removal of Back Cover(TR)
2-15.
Removal of FR-Board
2-16.
Removal of Fan (FR)
2-5-4.
Removal of Back Cover(R)
2-17.
Removal of DS-Board
2-18.
Removal of V2-Board
2-18-1. Removal of Control Asssy and Power button
2-19.
Removal of Speaker(R)
2-5-5.
Removal of Back Cover(L)
2-20.
Removal of Speaker(L)
DIS-9
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-4. Preparations
* When you exchange modules or board, in order to make it discharge from an electrolytic capacitor,
please wait for 1 minute after the power supply end.
* Please handle the LCD panel in standing state with crane.
please wait for 1 minute after the power supply end.
* Please handle the LCD panel in standing state with crane.
■
How to set the LCD module
Check Point
①
Pull up the LCD module
②
Approach the panel
③
After standing the panel
④
Finish.
with a crane.
to the stand and set
to vertically, set the panel
the lower hook to
to stand slowly.
lower hole of stand.
(Insert the upper hook to upper notch)
■
Precautions when replacing module.
* When you replace each parts, please be sure to carry out following procedure as below.
* Be careful not to overtighten the screws when replacing each module.
* Please remove a clamper and a wire processing tape if needed in the repair.
* Be careful not to overtighten the screws when replacing each module.
* Please remove a clamper and a wire processing tape if needed in the repair.
2-5. Removal of Back Cover
1. Remove the screws and Back Cover.
The screw located cut-out portion
■
Caution when removing Back Cover
*When repairing in an upside position of the Display, please remove the screws
while holding the Back Cover by hand to prevent the Back Cover from falling down.
*The screw located cut-out portion of Back Cover are fixing the cabinet block and
the LCD module.
THEL065Z : 148
[100±
[100±
20
N・㎝]
BACK_COVER_CORNER
BACK_COVER_CORNER
BACK_COVER_CORNER
DIS-10
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
2-5-1. Removal of Back Cover(BR)
2-5-4. Removal of Back Cover(R)
1. Remove the screws and then remove the Back Cover.
1.Remove the screws and then remove the Back Cover.
2-5-2. Removal of Back Cover(BL)
2-5-5. Removal of Back Cover(L)
1. Remove the screws and then remove the Back Cover.
1. Remove the screws and then remove the Back Cover.
2-5-3. Removal of Back Cover(TR)
1. Remove the screws and then remove the Back Cover.
THEL065Z : 30
[100±
[100±
20
N・㎝]
THEL065Z :28
[100±
[100±
20
N・㎝]
THEL065Z :18
[100±
[100±
20
N・㎝]
THEL065Z : 31
[100±
[100±
20
N・㎝]
THEL065Z : 23
[100±
[100±
20
N・㎝]
Click on the first or last page to see other TH-98LQ70U / TH-98LQ70W / TH-98LQ70C service manuals if exist.