Panasonic TH-98LQ70U / TH-98LQ70W / TH-98LQ70C Service Manual ▷ View online
DIS-19
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
9. Remove the Inlet Assy following the instructions on
14. Remove the screws and then remove Rear Frame.
"2-14 Removal of Inlet Assy".
First remove three Rear Frame (V/C) and then
10. Remove the V2-Board following the instructions
remove Rear Frame (HA/HB).
on "Removal of V2-Board".
(with rear frame fixing metal)
11. Remove the stand following the instructions on
"2-4 Preparations" and then put the LD module
calmly on the stable level place with a crane.
*
*
Do not put new LCD Panel on a plane.
12. Remove the screws and then remove the stand hook.
15. Remove the screws and then remove Rear Frame
LCD(Top/Bottom/L/R).
13. Remove the screws and then remove the Rear Frame
Covert and Bridge Angle.
Covert and Bridge Angle.
Finally remove the FFC cables (A-FR, FR-T-CON,
DS-HX) attached to LCD panel with pet tape.
The process of removal parts has been completed.
THEL065Z
: 12
[100±
20
N・㎝]
XYN4+F10FJ : 4
[100 ±
[100 ±
20
N・㎝]
THEC217J
: 12
[100±
20
N・㎝]
TMMX270
: 4
XWB16BVJ
: 4
THEA215
: 4
[400±
20
N・㎝]
XWP16FJ
: 4
The positions are third
and fifth from top side.
and fifth from top side.
XYN4+F10FJ :68
[100 ±
[100 ±
20
N・㎝]
XYN8+F20FJK : 4
[125 ±
[125 ±
20
N・㎝]
XYN3+F8FJ : 28
[60 ±
[60 ±
20
N・㎝]
DIS-20
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
16. Open the carton box of new LCD panel.
19. Pull up new LCD panel with the crane out of the carton
Remove the carton Top as following figure.
and remove alminum packing.
Next unwrap the stretch film and then remove Cushion
Note: Be careful not to damage the new panel
Top. Next open the upside of alminum packing.
by the chain of crane.
Note: Do not yet take the new LCD panel out of the
carton box.
17. Attach the Rear Frame (HA) which was removed in the
procedure 14 in standing condition in the carton box.
20. Attach the Rear Frame LCD (Bot) in the hung condition.
Next attach the Rear Frame LCD (Top) which was
removed in the procedure 15.
18. Set the rope or wire to the Rear Frame(HB) to pull up
the new LCD panel with a crane.
Note: Be careful not to damage the FFC of the new
panel by the rope or wire.
XYN3+F8FJ : 9
[60 ±
[60 ±
20
N・㎝]
XYN3+F8FJ : 9
[60 ±
[60 ±
20
N・㎝]
XYN8+F20FJK : 2
[125 ±
[125 ±
20
N・㎝]
Cushion
DIS-21
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
21. Spread cushion on the ground and place the new LCD panel
22. Attach the Rear Frame LCD (L/R) to the new LCD
on it slowly to touch all part of Rear Frame LCD(Bot).
panel in the condition of procedure 21.
The adjusting tension of the chain enables new LCD panel to
Next attach the Rear Frame (HB) to the new panel.
secure.
・
Rear Frame LCD (L/R) were removed in the procedure 15.
* Do not yet detach a crane from LCD panel.
・
Rear Frame LCD(HB) was removed in the procedure 14.
Note: Be careful not to give the shok to the new panel.
23. Support the new LCD panel as follwing figure not to
touch the screen
by two persons
. Remove the wire
or rope from the new LCD panel to detach/attach
the Rear Frame (HA).
the Rear Frame (HA).
*Do not put down LCD panel uneven.
XYN3+F8FJ : 10
[60 ±
[60 ±
20
N・㎝]
XYN4+F10FJ
: 24
[100 ±
20
N・㎝]
XYN8+F20FJK : 2
[125 ±
[125 ±
20
N・㎝]
XYN8+F20FJK : 2
[125 ±
[125 ±
20
N・㎝]
DIS-22
SECTION 2 DISASSEMBLY PROCEDURES
<TH-98LQ70>
24. Attach all parts that were removed in the procedure 14
26. Attach all PCB-Board that were removed in the
First, screw Rear Frame(HA/HB) and Rear Frame
procedure from 3 to 10.
LCD(L/R). Next, screw Rear Frame(V)(C) and Rear
27. Attach the Cabinet Block that were removed with
Frame LCD(Top/Bot) and Rear Frame (HA/HB).
procedure 2 following the instructions on "2-21.
Removal of Cabinet Block". And then connect
the cable(From V1-Board) to the HX11.
28. Please carry out the lighting test fllowing the
28. Please carry out the lighting test fllowing the
instructions on "3ー3ー1. LCD Panel test mode".
(When two FFC(FR-T-CON) are disconnected, LCD
Test Pattern is displayed. )
29. Attach all Back Covers following the instructions on
"2-5 Removal of Back Cover".
Test Pattern is displayed. )
29. Attach all Back Covers following the instructions on
"2-5 Removal of Back Cover".
25. First, attach the Rear Frame Cover that were removed
in the procedure 13.
Next, attach the stand hook that were removed
in the procedure 12.
Attach the eye bolt to Rear Frame(V)(C) and then pull
up the LCD panel with a crane to use the eye bolt.
And set the stand to following the instructions on
"2-4 Preparations" .
in the procedure 13.
Next, attach the stand hook that were removed
in the procedure 12.
Attach the eye bolt to Rear Frame(V)(C) and then pull
up the LCD panel with a crane to use the eye bolt.
And set the stand to following the instructions on
"2-4 Preparations" .
XYN4+F10FJ : 64
[100 ±
[100 ±
20
N・㎝]
Click on the first or last page to see other TH-98LQ70U / TH-98LQ70W / TH-98LQ70C service manuals if exist.