Panasonic KX-TGP600RUB / KX-TPA60RUB Service Manual ▷ View online
29
KX-TGP600RUB/KX-TPA60RUB
3-5. Downloading Complete
If downloading finished, display shows "Download finished successfully!".
Click "OK" then disconnect the serial PC cable.
7.2.
Air Down load
When you update TPA60 Firmware with Air Down load it must be registered to TGP600.
1. Register TPA60 to the TGP600.
Refere to Service Manula of TGP600 PS Registration.
Access to TGP600 WEB browser, and select Local Firm ware Update.
Note:
Access to TGP600 WEB browser, and select Local Firm ware Update.
Note:
When you update the PS Firmware , TGP600 should be operated in Normal Mode.
2. Firmware update
Select "Firmware Update" menu of the PS, refer to following procedure.
Select "Setting Handset".
Select "System Option".
Select "Firmware Update
Note:
Select "Setting Handset".
Select "System Option".
Select "Firmware Update
Note:
If the Firmware update is selected "Automatically" at the CS WEB, PS will start Firmware Update automatically after regis-
tration.
tration.
If the remaining battery power is less than level 1, PS should be set Charger cradle.
30
KX-TGP600RUB/KX-TPA60RUB
8 Test Mode
The various tests are available by using serial communication with your PC.
Serial TOOL is connected to CN100 for Test.
Serial TOOL is connected to CN100 for Test.
8.1.
How to execute Test command
1. Execute "Flash Program.exe"
2. Select "Test command" sheet.
3. Enter command in command columu.
4. Click "Send".
2. Select "Test command" sheet.
3. Enter command in command columu.
4. Click "Send".
*"FlashProgram" config setting
1. Open "Download" Tab.
2. Open "Config" window.
2. Open "Config" window.
Port = The COM port that connected to a PC
Chip Type = DCX
Baud Rate = 19200
Crystal Value = X2
Flash Rom = internal
Serial Cable = 3wire
Chip Type = DCX
Baud Rate = 19200
Crystal Value = X2
Flash Rom = internal
Serial Cable = 3wire
3. Open "Test command" Tab.
8.1.1.
Commands
Commandlist is below.
Command name
Function
Example
IDR
Read ID (RFPI)
Type “IDR”, and the registered ID is read out.
IDW
Write ID (RFPI)
Type “IDW 00 18 E0 0E 98”, and the ID “0018 E0 0E 98” is written.
VER
Read software version
Type “VER”.
SFR
Clock adjustment value
Type "SFR xx xx". xx xx starts at 0100. Depending on the value of the frequency of test point
SKM, it changes forward and backward. It ends when it is in range of 13.824MHz ± 7Hz.
SKM, it changes forward and backward. It ends when it is in range of 13.824MHz ± 7Hz.
LED
LED control
Type"LED D". All of the Ringer LED and the LCD Back Light light up..
Type "LED 1 (0)". The Ringer LED light up (light out).
Type "LED C (4)". The LCD Back Light light up (darken).
Type "LED 1 (0)". The Ringer LED light up (light out).
Type "LED C (4)". The LCD Back Light light up (darken).
BTX
Burst transmission in RF
Type "BTX 2F xx 31".
EUT outputs RF radio signal in xx channel. DECT 00 chanel is 1897.344MHz.
EUT outputs RF radio signal in xx channel. DECT 00 chanel is 1897.344MHz.
CRX
CW reception in RF
Type "CRX 1 xx" (xx : channel number. 1ch = "01").
RST
reset
Type "RST". EUT is reset.
EPD1
Factory settings
Type "EPD 1". Unit is reset to the Factory settings.
(Erase stored Phone numbers, Caller list and etc.)
This operation should not be performed for a usual repair.
(Erase stored Phone numbers, Caller list and etc.)
This operation should not be performed for a usual repair.
31
KX-TGP600RUB/KX-TPA60RUB
8.1.2.
How to "TX Power measurment". (Handset)
You can check TX power with Spectrum Anaralyzer.
First,operate the PC and Spectrum Analyzer setting, which is below.
Frequency 1897.344MHz / RBW 3MHz / REF level 30dBm / MAX hold
First,operate the PC and Spectrum Analyzer setting, which is below.
Frequency 1897.344MHz / RBW 3MHz / REF level 30dBm / MAX hold
1. Remove solder antenna jumper on ANT_JP and connect ANT_TP1 to Spectrum Analyzwer with Coaxial cable.
2. Handset power on.
3. Excute a command "BTX 2F 00 31".
4. Measure TX power with Spectrum Analyzer.
5. Confirm TX power is 20 - 24 dBm. Or Compare with the regular set.
6. Remove Coaxial cable and Repair antenna jumper.
2. Handset power on.
3. Excute a command "BTX 2F 00 31".
4. Measure TX power with Spectrum Analyzer.
5. Confirm TX power is 20 - 24 dBm. Or Compare with the regular set.
6. Remove Coaxial cable and Repair antenna jumper.
8.2.
Key/Soft key and Icon List
Note:
In the chapter 8, 9, 10, Keys and Soft keys are used for descriptions. Those Keys/Soft keys are displayed as icons in this model.
Refer to the following list for your information.
Refer to the following list for your information.
8.3.
Translation List
Note:
Default language varies depending on the destination.
32
KX-TGP600RUB/KX-TPA60RUB
8.4.
Test Burst Mode for Base Unit
Connect Base Unit to PC for Test mode with Serial cable. (Refer to Serial Test Mode (P.41).)
Power check
connect PC to TGP600 and Spectram analyzer to TGP600.
Step
Content
command
Description
1
Test Burst Sending RF POWER
*=Channel setting
0 or 1 or ... or 9
ie BTX 2F 05 CC
0 or 1 or ... or 9
ie BTX 2F 05 CC
2
Antenna setting
*=antenna setting
1 or 2
1 or 2
Step
Content
command
Description
1
Test Burst Sending RF POWER
*=Channel setting
0 or 1 or ... or 9
ie BTX 2F 05 CC
0 or 1 or ... or 9
ie BTX 2F 05 CC
2
Antenna setting
*=antenna setting
1 or 2
1 or 2
DCX_UTX
3.2V
LF
DG4
ANT_JP1
ANT_JP2
VBG
T
CK
T
DI
T
DO
ANT_TP1
ANT_TP2
TCK_1
TMS_1
BCLK
TDI_1
T
MS
DCX_URX
TDO_1
L200
1.3VDD
RTCK_1
T
RST
PNLB2350Z
KX-TGP600xx
CE M UK
LC BR C
AL RU LA
OPEN
HOT
ANT1
ANT2
GND
GND
HOT
OPEN
GND
URX
UTX
*
btx 2F 0 CC
ant
*
PC
Spectrum analyzer
TGP600
*
btx 2F 0 CC
ant
*
Click on the first or last page to see other KX-TGP600RUB / KX-TPA60RUB service manuals if exist.