Panasonic AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G Service Manual ▷ View online
DIS-9
10. Removal of Cassette Cover Unit
1. Remove the MIC Case Unit.
2. Remove the Side case R Unit.
3. Remove the POWER C.B.A..
4. Remove the TOP VF Unit.
5. Remove the Front Case Unit.
6. Remove the Lens Unit.
7. Remove the Rear Case Unit and CAMERA C.B.A..
8. Unscrew the 2 screws (A) and remove the Cassette Cover Unit as shown in figure 10-1.
Figure 10-1
(Note in installation)
1. Pass flexible cable through the portion “A” as shown in figure 10-2.
2. Attach the “B” portion to “C” portion as shown in figure 10-2 and tighten the 2 screws (A).
Figure 10-2
SCREW (A)
A
CASSETTE COVER UNIT
B
B
C
C
DIS-10
11. Removal of Mechanism Unit & VTR C.B.A.
1. Remove the MIC Case Unit.
2. Remove the Side Case R Unit.
3. Remove the POWER C.B.A..
4. Remove the TOP VF Unit.
5. Remove the Front Case Unit.
6. Remove the Lens Unit.
7. Remove the Rear Case Unit and CAMERA C.B.A..
8. Remove the Cassette Cover Unit.
9. Disconnect the connector P2219 and P2222 on VTR C.B.A. as shown in figure 11-1.
10. Disconnect the connector P2217 on VTR C.B.A. and P4101 on SIDE JACK C.B.A., then remove the flexible
cable (A) as shown in figure 11-1.
11. Unscrew the 6 screws (A) and remove the Unit (Mechanism & VTR C.B.A.) as shown in figure 11-1.
Figure 11-1
NOTE: MECH Attachment Frame requires replacement, make sure to move the Cooling Sheet to the new MECH
Attachment Frame. See figure 11-1.
A
B
C
Cooling Sheet
Flexible Cable
(A)
(A)
SCREW (A)
SCREW (A)
SCREW (A)
SCREW (A)
SIDE CASE L UNIT
P2222
P2217
P4101
(Connection of A, B and C)
P2217
P2222
P4101
P2219
DIS-11
12. Disconnect the 7 connectors (A),(B),(C),(D),(E),(F) and (G) on VTR C.B.A. as shown in figure 11-2.
Figure 11-2
13. Unscrew the 2 screws (B) and remove the VTR C.B.A. as shown in figure 11-3.
14. Unscrew the 3 screws (C) and remove the Mechanism Unit from Mech. Attachment Frame Unit as shown in
figure 11-3.
15. Unscrew the 2 screws (D) and remove the Garage Cover as shown in figure 11-3.
NOTE: In case a new Mechanism unit is installed, put the FPC Protection Sheet in the following position as
shown in figure 11-3.
Figure 11-3
(C) (D)
(A)
(B)
(E)
(F)
(G)
Put sheet at the end of the mechanic chassis.
FPC Protection Sheet
Mechanism Unit
Mech. Attachment Frame Unit
Hook to Mech. Attachment Frame Unit
SCREW (B)
VTR C.B.A
SCREW (B)
SCREW (C)
Garage Cover
SCREW (D)
DIS-12
12. Removal of LCD Unit
1. Remove the MIC Case Unit.
2. Remove the Side Case R Unit.
3. Unscrew the 3 screws (A) and remove the HEAT SINK(SIDE R) as shown in figure 12-1.
4. Remove the FFC Protection Sheet as shown in figure 12-2.
5. Remove the Cooling Sheet to unscrew the screw (B) and unscrew the screw (B) and (C) as shown in figure
12-2.
6. Remove the HINGE COVER and unscrew the 2 screws (D) as shown in figure 12-3.
7. Disconnect connector P6404 on R SIDE C.B.A. and remove the LCD Unit as shown in figure 12-2.
(Note in installation)
1. When installing the FFC Protection Sheet, fully open the LCD Panel and Put on the original position as shown
in figure 12-2.
2. Do not forget put on the Cooling Sheet after tightening the screw (B) as shown in figure 12-2.
Figure 12-1
Figure 12-2
Figure 12-3
LCD PANEL UNIT
SCREW (D)
HINGE COVER
SCREW (A)
SCREW (A)
HEAT SINK (SIDE R)
SCREW (B)
SCREW (C)
FFC Protection Sheet
Cooling Sheet
P6404
Click on the first or last page to see other AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G service manuals if exist.