Panasonic AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G Service Manual ▷ View online
DIS-5
6. Removal of TOP VF Unit
1. Remove the MIC Case Unit.
2. Remove the Side Case R Unit.
3. Unscrew the 4 screws (A) as shown in figure 6-1.
4. Lift up the TOP VF and disconnect a connector P2215 on VTR C.B.A., then remove the TOP VF Unit as
shown in figure 6-1. Then be careful because the portion A and B are hooked together.
(Note in installation)
1. In case the flexible cable (A) is changed to new one, bend it to Z character as shown in figure 6-1.
2. The CCD Heat Sink is located to outside of TOP VF Unit as shown in figure 6-1.
Figure 6-1
SCREW (A)
Hook the A to B portion.
SCREW (A)
TOP VF UNIT
A
B
Flexible Cable (A)
P2215
Do not give
damage to cable
damage to cable
Outside of TOP VF Unit
DIS-6
7. Removal of Front Case Unit
1. Remove the MIC Case Unit.
2. Remove the Side Case R Unit.
3. Remove the TOP VF Unit.
4. Unscrew the 3 screws (A) as shown in figure 7-1.
5. Disconnect a connector P6301 and remove the Front Case Unit as shown in figure 7-1.
(Note in installation)
1. When installing the Front Case Unit, do not give damage the Lens.
2. In case of the flexible cable (it connected with P6301 and CAMERA C.B.A.) is exchange to new one, bend it
to Z character to put under the Lens Unit.
Figure 7-1
FRONT CASE UNIT
Be careful not to damage the lens.
Bend flexible cable to put under the Lens Unit.
SCREW (A)
SCREW (A)
P6301
DIS-7
8. Removal of Lens Unit
1. Removal of MIC Case Unit.
2. Removal of Side Case R Unit.
3. Removal of POWER C.B.A..
4. Removal of TOP VF Unit.
5. Removal of Front Case Unit.
6. Unscrew the 2 screws (A) and remove the CCD CON STOPPER as shown in figure 8-1.
7. Disconnect the connector P1 and P8 on CAMERA C.B.A. as shown in figure 8-1.
8. Unscrew the 4 screws (B) and remove the Lens Unit.
9. Unscrew the 4 screws (C) and remove the Lens Frame Unit from Lens Unit as shown in figure 8-1.
(Note in installation)
1. In case a new Lens Unit is installed, bend the flexible cable (A) to Z character as shown in figure 8-1.
Figure 8-1
SCREW (A)
P8
P1
CCD CON STOPPER
SCREW (B)
LENS UNIT
Bend to Z character
(A)
SCREW (B)
Lens Frame Unit
SCREW (C)
DIS-8
9. Removal of Rear Case Unit & CAMERA C.B.A.
1. Removal of MIC Case Unit.
2. Removal of Side Case R Unit.
3. Removal of POWER C.B.A..
4. Removal of TOP VF Unit.
5. Removal of Front Case Unit.
6. Removal of Lens Unit.
7. Remove the 3 screws (A) as shown in figure 9-1.
8. Disconnect a connector P2 on CAMERA C.B.A. as shown in figure 9-1.
9. Unscrew the 2 screws (B) on CAMERA C.B.A. as shown in figure 9-1.
10. It shifts the Rear Case Unit as much as showing in figure 9-1 and remove the CAMERA C.B.A.. Be careful
because the VTR C.B.A.(bottom side of CAMERA C.B.A.) and the connector in the CAMERA C.B.A are
combined.
11. Disconnect a connector P2216 on VTR C.B.A. and remove the Rear Case Unit.
(Note in installation)
1. When installing the CAMERA C.B.A., Attach the CAMERA C.B.A. to portion “A” of Mech. Attachment Frame
as shown in figure 9-1.
2. When installing the CAMERA C.B.A., the parts which are shown in figure 9-1 on the CAMERA C.B.A. are
combined with the VTR C.B.A. with the direct connector, pushing CAMERA C.B.A. well.
3. When installing the Rear Case Unit, it puts section “B” in the hole of flexible cable, which is connected in
P2216 as shown in figure 9-1.
Figure 9-1
SCREW (B)
Hook to Frame.
There is a direct connector in
the bottom and push well.
REAR CASE UNIT
CAMERA C.B.A
P2216
P2
SCREW (A)
SCREW (A)
SCREW (A)
A
B
Click on the first or last page to see other AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G service manuals if exist.