Panasonic AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G Service Manual ▷ View online
MECH-3
3. Connect the Connection Adapter (VFK1763) to EVR connector in Unit. Then make sure that the direction of the
VFK1309A and VFK1763 are correct as shown in Figure.
1-5. Connection of LISTA Adjustment System
TAPE
VFM3000EDS (DV LISTA)
M. EQ
Personal Computer (A/D Board should be installed.)
TOOL
VFK1481K (LISTA Software), VFK1186 (LISTA Cable), VFK1300 (A/D Converter Board),
VFK1308P (Measuring Board), VFK1409A (Measuring Board) ← NOTE 2
VFK1317 (30P flat cable): 2pcs, VFK1309A (EVR connector board) ← NOTE 1
VFK1763 (Connection Adapter), VJA0941 (DC cable): 2pcs, 9P RS232C cross cable.
VFK1308P (Measuring Board), VFK1409A (Measuring Board) ← NOTE 2
VFK1317 (30P flat cable): 2pcs, VFK1309A (EVR connector board) ← NOTE 1
VFK1763 (Connection Adapter), VJA0941 (DC cable): 2pcs, 9P RS232C cross cable.
TP
In case of use VFK1409A
F2
F2
: ATF-ERR (VFK1409A), TP2 : TRG/HSW (VFK1409A), GND : GND (VFK1409A)
In case of use VFK1409S
F2
F2
: ATF-ERR (VFK1409S), TP2 : TRG/HSW (VFK1810), GND : GND (VFK1409S)
NOTE 1:
VFK1309 and VFK1309A can be used to perform LISTA adjustment. The VFK1309A is only required for LCD
adjustment (refer to item 1 of Electrical adjustment procedure in section 4.)
NOTE 2:
If you already have VFK1409S (Measuring board), it can be used to perform LISTA adjustment with VFK1810.
Please refer to next explanation for installation of VFK1409S.
When the VFK1763 is connected
the EVR connector, be careful
that VFK1309A is attached in the
right direction.
the EVR connector, be careful
that VFK1309A is attached in the
right direction.
MECH-4
1. Set the switches on the Measuring Board as shown below.
<VFK1308P>
SW NAME& No.
Setting Position
RS232C SEL (SW101)
D-SUB
VTR TEST (SW103)
L
BST TEST (SW104)
NORMAL
SW105 H
SW106 OFF
SW107 CENTER
SW106 OFF
SW107 CENTER
position
SW108 H
FLUSH1 (SW102)
FLUSH1 (SW102)
NORMAL
FLUSH2 (SW109)
NORMAL
<VFK1409S or VFK1409A>
SW NAME& No.
Setting Position
RS232C SEL (S110)
D-SUB
REC I (S101)
NOR
LSI TEST (S102)
NOR
S104 NOR
S114 EXT
S201 Right
S114 EXT
S201 Right
side
S202 Right
side
S203 Right
side
LISTA ON-OFF
ON
1. Install the two test points of VFK1810 to through hole in this area and solder it at test point
at foil side of VFK1409S to fixed VFK1810.
VFK1810
Red colour of Lead wire
Black colour of Lead wire
TP1
TP2
2. Insert the two lead wires of VFK1810 to through hole.
3. Solder the red color of lead wire to pin1 of P108 on foil side on VFK1409S.
4. Solder the black color of lead wire to pin3 of P106 on foil side on VFK1409S.
VFK1409S
MECH-5
2. Connect a PC, the Measuring Board and the camera recorder as shown below.
<CONNECTION>
1) In case of use VFK1409A
2) In case of use VFK1409S
3. Connect the clips of the LISTA cable to test point on the Measuring Board. (Refer to Items “Sensitivity
2) In case of use VFK1409S
3. Connect the clips of the LISTA cable to test point on the Measuring Board. (Refer to Items “Sensitivity
Detection”
and “Linearity Adjustment”.)
GND
ATFI
HID 1
D GND
TP1
TP2
F2
ATFI
DC6V to 9V
DC6V to 9V
Connect the EVR connector of
camera recorder. It required 2 pieces
of VFK1317, VFK1309A and
camera recorder. It required 2 pieces
of VFK1317, VFK1309A and
VFK1763
.
(Refer to item “1-4. Connection
of EVR tools.”)
of EVR tools.”)
9P RS232C CROSS CABLE
PC W/AD board
LISTA CABLE (VFK1186)
Short jumper
Short jumper
VFK1308P
VFK1409A
GND
ATFI
HID 1
D GND
TP1
TP2
F2
ATFI
DC6V to 9V
DC6V to 9V
Connect the EVR connector of
camera recorder. It required 2 pieces
of VFK1317, VFK1309A and
camera recorder. It required 2 pieces
of VFK1317, VFK1309A and
VFK1763
.
(Refer to item “1-4. Connection
of EVR tools.”)
of EVR tools.”)
9P RS232C CROSS CABLE
PC W/AD board
LISTA CABLE (VFK1186)
Short jumper
Short jumper
VFK1308P
VFK1409S
VFK1810
MECH-6
1-6. Boot up the LISTA Software
1. Boot up the LISTA software on DOS mode.
2. After boot up the LISTA software, <<< FORMAT SELECT >>> display appears. Select the item “DV”.
2. After boot up the LISTA software, <<< FORMAT SELECT >>> display appears. Select the item “DV”.
After select the format, <<< VTR SELECT >>> display appears, and select the model “AG-DVC200”.
3. Next, select the Serial number of the Alignment tape on the screen. In case of LISTA software is not entered with
data of alignment tape, press the ESC key, then main menu is displayed on the screen. And select the item “<4>
Alignment Tape”
Alignment Tape”
for entry the data on the attachment sheet, which is enclosed with alignment tape.
4. In case of LISTA software has entered data of alignment tape, select the serial number of Alignment tape, then
message appears “ok? (y/n)” on the screen. And press “ Y ” or “ ENTER ” key, then LISTA main menu is
displayed on screen.
displayed on screen.
< In case of Alignment Tape entered already >
< In case of Alignment Tape does not entered >
< How to Install and Boot Up >
Make a directory like C: LISTA and copy all files in the VFK1481K(LISTA Software) to it on PC.
Type “LISTA” and press ENTER key, then boot up the LISTA software VFK1481K.
Make a directory like C: LISTA and copy all files in the VFK1481K(LISTA Software) to it on PC.
Type “LISTA” and press ENTER key, then boot up the LISTA software VFK1481K.
Click on the first or last page to see other AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G service manuals if exist.