Panasonic AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G Service Manual ▷ View online
MECH-7
1-7. How to Enter the Alignment Tape Data
1. Select the item “<4> Alignment Tape” on the LISTA main menu.
2. Select the item “<2> ENTRY” on the alignment menu.
3. After the screen displays the screen of <<Alignment Tape Data Entry>>, first input the Serial Number follow
2. Select the item “<2> ENTRY” on the alignment menu.
3. After the screen displays the screen of <<Alignment Tape Data Entry>>, first input the Serial Number follow
the printed number on the tape label. And input the number “0” or “1” for selected the PAL/NTSC. And after
that enter the tape type, input “0” for DVCPRO, input “1” for DV or input “2” for HDLP.
that enter the tape type, input “0” for DVCPRO, input “1” for DV or input “2” for HDLP.
4. After selecting the tape type, the frame for inputting the DATA and CHECK SUM appears on the screen. Input
the numerical value in numerical order on the data sheet, which is enclosed with alignment tape. If the wrong
number is inputted, the error message on the screen, then confirm that data on the sheet.
number is inputted, the error message on the screen, then confirm that data on the sheet.
5. After the data entry, the screen returns to “LISTA MAIN” menu. Confirm the serial number of the alignment
tape.
<< Alignment Tape Data Entry >>
Serial No. Lrc-20 (NTSC) 10
µµµµ
m
[1]
- 0.1
[11]
0.7
[21]
- 0.4
[31]
- 0.4
[2]
0.1
[12]
1.0
[22]
- 0.2
[32]
- 0.6
[3]
0.0
[13]
0.7
[23]
- 0.7
[33]
- 0.3
[4]
0.2
[14]
0.5
[24]
- 0.6
[34]
- 0.2
[5]
0.6
[15]
0.2
[25]
- 0.7
[35]
- 0.1
[6]
0.5
[16]
- 0.5
[26]
- 0.3
[36]
- 0.3
[7]
0.7
[17]
- 0.3
[27]
- 0.4
[37]
- 0.1
[8]
0.9
[18]
- 0.3
[28]
- 0.4
[9]
1.0
[19]
- 0.1
[29]
- 0.6
[CS]
- 0.6
[10]
0.8
[20]
- 0.6
[30]
- 0.3
NOTE:
This is sample only, you must enter information from your alignment tape. Each tape is different.
MECH-8
1-8. LISTA Sensitivity Detection
TP
In case of use VFK1409A
F2
F2
: ATF-ERR (VFK1409A), TP2 : TRG/HSW (VFK1409A), GND : GND (VFK1409A)
In case of use VFK1409S
F2
F2
: ATF-ERR (VFK1409S), TP2 : TRG/HSW (VFK1810), GND : GND (VFK1409S)
VTR MODE
PLAY
ADJ. MODE
Refer to below explanation
TAPE
VFM3000EDS (DV LISTA)
SPEC.
40 mV /
µ
m to 120 mV /
µ
m
1. Set the camera recorder to VCR mode.
2. Insert the DV Alignment Tape (VFM3000EDS) to the camera recorder.
3. Press the MENU button to open the “VCR FUNCTION MENU”.
4. Open
the
“8. ADJUST MENU”
in “VCR FUNCTION MENU”.
5. Select the item “ATF GAIN” and press the MULTI-DIAL.
6. Message
6. Message
“NOW SERVO ADJUST PUSH MENU TO RETURN”
appears on screen and press the PLAY button
to playback the tape.
7. Press MENU button to return to “ADJUST MENU” screen.
8. Select
8. Select
item
“<1> Sensitivity Measurement”
on the LISTA main menu, and press “ENTER”.
9. Then the tape is played back (tape speed : 101.2%) automatically, and message “1.2% Speed…” appears on
the screen.
10. Press the ENTER key, and then start measurement of the sensitivity value.
11. Confirm that the sensitivity value is with in specification, after the message “<<Sensitivity Measurement
11. Confirm that the sensitivity value is with in specification, after the message “<<Sensitivity Measurement
Finish>>”
.
Figure 9
<<Sensitivity Measurement Finish>>
Sensitivity 72.95
(mV/um)
Sens.1
65.43 (mV/um)
Sens.1
85.48 (mV/um)
Confirm that the value of Sens.Value1
and Sens.Value2 in specification
and Sens.Value2 in specification
Select at Sensitivity Detection.
MECH-9
1-9. LISTA Linearity Adjustment
TP
In case of use VFK1409A
F2
F2
: ATF-ERR (VFK1409A), TP2 : TRG/HSW (VFK1409A), GND : GND (VFK1409A)
In case of use VFK1409S
F2
F2
: ATF-ERR (VFK1409S), TP2 : TRG/HSW (VFK1810), GND : GND (VFK1409S)
ADJ.
S1 and T1 Post Height
VTR MODE
PLAY
ADJ. MODE
Refer to below explanation
TAPE
VFM3000EDS (DV LISTA)
TOOL
VFK1899 : Post Driver
SPEC.
Linearity : less than 3
µ
m
1. Set the camera recorder to VCR mode.
2. Insert the DV Alignment Tape (VFM3000EDS) to the camera recorder.
3. Press the MENU button to open the “VCR FUNCTION MENU”.
4. Open
the
“8. ADJUST MENU”
in “VCR FUNCTION MENU”.
5. Select the item “LINEARITY” and press the MULTI-DIAL.
6. Message
6. Message
“NOW SERVO ADJUST PUSH MENU TO RETURN”
is appears on screen and press the PLAY
button to playback the tape.
7. Press MENU button to return to “ADJUST MENU” screen.
8. Select
8. Select
item
“<2> Linearity Measurement”
on the LISTA main menu, and press “ENTER”, then the Linearity
Waveform appears.
9. When the waveform as shown in figure below is displayed on the screen, press the “BS (Back Space)” key
for display the waveform positioned at the center of the scale on screen. Adjust S1 and T1 post height by
using the post driver so that the linearity waveform is becomes flat as possible, and it should be within
specification.
(Adjust linearity waveform in the red dot line on the screen.)
using the post driver so that the linearity waveform is becomes flat as possible, and it should be within
specification.
(Adjust linearity waveform in the red dot line on the screen.)
Select at Linearity Measurement.
MECH-10
Figure 10
10. Press “SPACE” key to perform the Peak Hold in 30 seconds when linearity is displayed.
11. After finishing the Peak Hold, press “SHIFT” and “ } ” key simultaneously on the Key Board, then the
numerical values of “Linearity” and “Waving” is displayed on left lower portion of screen. And confirm the
numerical value of “Linearity” is in the specification. If the “Linearity” is out of specification, adjust height of
S1 and T1 post.
numerical value of “Linearity” is in the specification. If the “Linearity” is out of specification, adjust height of
S1 and T1 post.
12. After this measurement is finished, press the ESC key to return to the main menu.
POINT :
The left side of the waveform (entrance side) is adjusted by the height of S1 post and the right side of the
waveform (exit side) is adjusted by the height of T2 post.
When the post driver is removed from upper part of post, linearity waveform is changed.
After finishing this adjustment, eject the tape and insert the tape again to confirm that the shape of the linearity
waveform has not changed.
The left side of the waveform (entrance side) is adjusted by the height of S1 post and the right side of the
waveform (exit side) is adjusted by the height of T2 post.
When the post driver is removed from upper part of post, linearity waveform is changed.
After finishing this adjustment, eject the tape and insert the tape again to confirm that the shape of the linearity
waveform has not changed.
Adjust Linearity
into this area.
into this area.
Confirm this value
Click on the first or last page to see other AG-DVC30P / AG-DVC30E / AG-DVC32EN / AG-DVC33MC / AG-MYA30G service manuals if exist.