Panasonic PT-RZ21KE / PT-RS20K Service Manual ▷ View online
ADJ-9
SECTION 3 ADJUSTMENTS
< RZ21K / RS20K >
1. 4. Adjusted data transfer
f
When it is necessary to replace [A]-P.C.Board or [DG]-P.C.Board, adjusted data backup and restore can be done via the
LAN terminal. SERIAL terminal connection can not be used.
1. 4. 1. Equipment to be used
1. Computer : Use it for the transfer of backup data.
2. Communication cable : LAN cable (When connecting directly, use a cross cable)
3. Service Software : [LogTool.exe (Ver. 2.0.1.4~)] Download from the projector service website.
1. 4. 2. Connection Preparations
1. Check the settings of the projector
1) Select the sub menu [DIGITAL LINK MODE] of main menu [NETWORK] and set it to [AUTO] or [ETHERNET].
2) Check the network IP address of the projector and take a note.
3) Set the IP address of computer to approximate (same network group) value of the projector IP address.
2. Connect the projector and the PC by using a communication cable.
(Connection example)
1. 4. 3. Backup the Adjusted data (before circuit board exchange)
1. Switch the projector to "Normal-Standby" mode (ON/STANDBY indicator is lighting in red).
2. Start up service software [LogTool.exe] with a computer.
3. The projector connection setting window appears.
1) Select [Option] → [Password] to display the password input window.
2) Enter the service password and then click [OK] button.
LAN cable (straight)
LAN cable (straight)
Projector LAN
Computer
Hub
• If you have changed the each menu settings, please return settings of the original (customers) after work.
①
②
③
• Adjusted data transfer for [DG]-P.C.Board, it is necessary for the main firmware version to be 3.00 or later.
If the version is earlier than 3.00, the adjusted data will not be transferred.
ADJ-10
SECTION 3 ADJUSTMENTS
< RZ21K / RS20K >
4. Select [LAN] of connection method and setup the connection information to connect to the projector.
f
In case of known IP address of projector
• Select [Manual] and setup the [IP address, Port (Command Port)] and then click [Connect] button.
①
②
③
f
In case of unknown IP address of projector
• Select [Search] and setup the [IP Address/subnet mask] to the same network of the projector and [Port(Command
port)] and then click [Search] button.
• After searching result, the available projectors are listed on the window as the below.
Check mark the projector for which you want to acquire the system log and then click [OK] button.
①
②
③
ADJ-11
SECTION 3 ADJUSTMENTS
< RZ21K / RS20K >
5. Read the Adjusted data file by the following procedure.
① Select the projector name to read of Adjusted data.
② Select a [Service] tab.
③ Click [Receive] button.
6. Select the save place and click [Save(S)] button.
7. The data save is complete when the "Complete" dialog window appears.
Click [OK] button to close the window.
①
②
③
ADJ-12
SECTION 3 ADJUSTMENTS
< RZ21K / RS20K >
1. 4. 4. Restore the backup Adjusted data (after circuit board replace)
1. Start up service software [LogTool.exe] with a computer according to steps 1 - 4 of "1. 4. 3. Backup the Adjusted data
(before circuit board exchange)" and connect it to the projector.
2. Restore the Adjusted data file by the following procedure.
① Select the projector name to send of Adjusted data.
② Select a [Service] tab.
③ When replacing [A]-P.C.Board, check-mark [Replace A-Pwb] in "Data Restore".
When replacing [DG]-P.C.Board, check-mark [Replace DG-Pwb] in "Data Restore".
④ Click [Send] button in "Data Restore".
3. Select the saved file and click [OPEN(O)] button.
①
②
③
④
4. Once the progress bar reaches the right side end and when the "Complete" dialog window appears, it is a write comple-
tion of the data. Click [OK] button to close the window and quit the software.
• Turn off the main power, turn on the power again, and check that it operates properly.
Click on the first or last page to see other PT-RZ21KE / PT-RS20K service manuals if exist.