Panasonic KX-MB3030RU / KX-FAP106A7 Service Manual ▷ View online
105
KX-MB3030RU
10 Test Mode
10.1. Test Functions
The codes listed below can be used to perform simple checks of some of the unit’s functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
Test Mode
Type of Mode
Code
Function
Operation after code
input
MEMORY CLEAR
Service Mode
“5” “5” “0”
Clear the memory where the users can store data.
SET
MOTOR TEST
Service Mode
“5” “5” “6”
00:printer motor feed 10:auto document feed (single side) 20:carriage 30:auto
document feed (double side)
document feed (double side)
SET
MODEM TEST
Service Mode
“5” “5” “4”
Telephone line circuit is connected automatically, output the following signals on
the circuit line.
1) OFF 2)1100Hz 3)2100Hz 4) V21 ter 300bps 5) V27 ter 2400bps 6) V27
ter 4800bps
7) V29 7200 8)V29 9600bps 9) V17 7200bps 10) V17 9600bps
11) V17 12000bps 12) V17 14400bps 13) V34 2400bps 14) V34 4800bps
15)V34 7200bps 16)V34 9600bps 17) V34 12000bps 18) V34 14400bps
19)V34 16800bps 20)V34 19200bps 21) V34 21600bps 22) V34 24000bps
23)V34 26400bps 24)V34 28800bps 25) V34 31200bps 26) V34 33600bps
the circuit line.
1) OFF 2)1100Hz 3)2100Hz 4) V21 ter 300bps 5) V27 ter 2400bps 6) V27
ter 4800bps
7) V29 7200 8)V29 9600bps 9) V17 7200bps 10) V17 9600bps
11) V17 12000bps 12) V17 14400bps 13) V34 2400bps 14) V34 4800bps
15)V34 7200bps 16)V34 9600bps 17) V34 12000bps 18) V34 14400bps
19)V34 16800bps 20)V34 19200bps 21) V34 21600bps 22) V34 24000bps
23)V34 26400bps 24)V34 28800bps 25) V34 31200bps 26) V34 33600bps
SET
ROM CHECK
Service Mode
“5” “5” “1”
Indicates the version and checks the sum of the ROM.
SET
LCD TEST
Service Mode
“5” “5” “8”
Checks the LCD indication.
Illuminates all the dots to check if they are normal.
Illuminates all the dots to check if they are normal.
SET
DTMF SINGLE
TONE TEST
TONE TEST
Service Mode
“5” “5” “2”
Outputs the DTMF as single tones. Used to check the frequencies of the individ-
ual DTMF tones. Refer to DTMF Single Tone Transmit Selection (P.107).
ual DTMF tones. Refer to DTMF Single Tone Transmit Selection (P.107).
1....ON
2....OFF
LED TEST
Service Mode
“5” “5” “7”
All LEDs above the operation panel board flash on and off, or are illuminated.
KEY TEST
Service Mode
“5” “6” “1”
Checks the button operation.
Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.107).
Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.107).
SCANNER TEST
Service Mode
“5” “5” “5”
LED lights up, Scanner scanning.
1:RED / 2:GREEN / 3:BLUE
1:RED / 2:GREEN / 3:BLUE
SET
LSU TEST
Service Mode
“6” “3” “9”
Laser radiates, Polygon rotates
SET
FAN TEST
Service Mode
“6” “7” “7”
01: Normal operation 02: Fuser Fan ON (High speed)
03: Fuser Fan ON (Low speed) 04: PSU Fan ON (High speed)
05: PSU Fan ON (Low speed) 06: Both Fan OFF
03: Fuser Fan ON (Low speed) 04: PSU Fan ON (High speed)
05: PSU Fan ON (Low speed) 06: Both Fan OFF
SET
MEMORY CLEAR
(except History data)
(except History data)
Service Mode
“7” “1” “0”
Refer to Memory Clear Specification (P.112).
SET
106
KX-MB3030RU
Note:
The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.
SENSOR CHECK
Service Mode
“8” “1” “5”
First of all, press the copy button, and confirm the action of ON/OFF.
For each sensor’s operation, refer to Sensors and Switches Section (P.55).
LCD DISPLAY:
For each sensor’s operation, refer to Sensors and Switches Section (P.55).
LCD DISPLAY:
D: Document
D: Document set
-: No document
-: No document
S: Read position
S: Docu detect
-: No document
-: No document
C: Left cover
C: Cover open
-: Cover close
-: Cover close
P: Paper (Standard input tray)
P: Recording paper set
-: No recording paper
-: No recording paper
R: Registration
R: Paper detect
-: No paper
-: No paper
E: Paper ejection sensor
E: Paper detect
-: No paper
-: No paper
D: Drum
D: DRUM set
-: No DRUM
-: No DRUM
T: Toner
T: Toner detect
-: No toner
-: No toner
*: None
3F: Fuser thermistor
3F: 00 (high temp.) - FF (low temp.)
*: None
DF: Fuser thermistor
DF: 00 (high temp.) - FF (low temp.)
*: None
*: None
C: Standard input tray
C: Tray open
-: Tray close
-: Tray close
*: None
T: Print timing
T: Paper detect
-: No paper
-: No paper
*: None
*: None
H: Carriage
H: Carriage detect
-: No carriage
-: No carriage
D: ADF Dpulex sensor
D: Document detect
-: No document
-: No document
*: None
A: ADU sensor
A: Paper detect
-: No paper
-: No paper
N: First use sensor
N: New
-: Secondhand
-: Secondhand
C: Drum contact sensor
C: Contact
-: Noncontact
-: Noncontact
*: None
L: Left cover (Optional lower
input tray)
L: Cover open
-: Cover close
-: Cover close
C: Optional lower input tray
C: Tray open
-: Tray close
-: Tray close
P: Paper (Optional lower input
tray)
P: Recording paper set
-: No recording paper
-: No recording paper
U: Pick up (Optional lower input
tray)
U: Paper detect
-: No paper
-: No paper
PRINT TEST PAT-
TERN
TERN
Service Mode
“8” “5” “2”
1. As “PATNO. =” is displayed on the LCD, enter the test pattern No. and press
the SET key.
2. When “NO. = “is displayed on the LCD, enter the printing number and press the
SET key. (Press “00” for the infinite printing.)
3. “MODE =” is displayed on the LCD. Press “0” to start printing or press “1” to go
to the next screen.
4. When “1” is pressed at MODE, “INTVL = “is displayed on the LCD. Enter the
printing interval (000~999 sec).
5. The printing repeats the designated number of times at the programmed print-
ing intervals.
the SET key.
2. When “NO. = “is displayed on the LCD, enter the printing number and press the
SET key. (Press “00” for the infinite printing.)
3. “MODE =” is displayed on the LCD. Press “0” to start printing or press “1” to go
to the next screen.
4. When “1” is pressed at MODE, “INTVL = “is displayed on the LCD. Enter the
printing interval (000~999 sec).
5. The printing repeats the designated number of times at the programmed print-
ing intervals.
Test Mode
Type of Mode
Code
Function
Operation after code
input
107
KX-MB3030RU
10.1.1. DTMF Single Tone Transmit Selection
Note:
After performing this check, do not forget to turn the setting off.
otherwise, dialing in DTMF signal will not work.
otherwise, dialing in DTMF signal will not work.
10.1.2. Button Code Table
108
KX-MB3030RU
10.1.3. Print Test Pattern
1. NO.01
2. NO.06
3. NO.03
• These print test patterns are just image printing, and differ-
ent from actual ones.
• When it is required to judge the print quality, compare with
the printing of a nondefective machine.
Click on the first or last page to see other KX-MB3030RU / KX-FAP106A7 service manuals if exist.