Panasonic KX-MB3030RU / KX-FAP106A7 Service Manual ▷ View online
93
KX-MB3030RU
2.
Before loading a stack of paper, fan the paper to prevent paper jams.
3.
Pinch the right side of the recording paper guide (2), then slide it to
match the paper size mark.
Pinch the front and back recording paper guides (3) at the same time,
then slide them together to match the paper size mark.
match the paper size mark.
Pinch the front and back recording paper guides (3) at the same time,
then slide them together to match the paper size mark.
4.
Load the paper, print-side up (4).
Important:
• Push down to lock the plate (5) in the standard input tray, if neces-
sary.
• Make sure that the recording paper guides (6) are at the paper size
mark and the recording paper is under the paper limit mark (7). The
paper should not be loaded over the tab (8).
paper should not be loaded over the tab (8).
94
KX-MB3030RU
Caution for the standard input tray
5.
Insert the standard input tray into the unit, lifting the front part of the
tray. Then push it completely into the unit.
tray. Then push it completely into the unit.
Note:
• If the paper is not loaded correctly, re-adjust the paper guides, or
the paper may jam.
• If the standard input tray does not close, the plate in the standard
input tray may not be in the locked position. Push the paper down
and make sure that the paper is lying flat in the standard input tray.
and make sure that the paper is lying flat in the standard input tray.
• Do not drop the standard input tray.
• Hold the standard input tray with both hands when removing
or installing. The standard input tray weighs approximately 4.8
kg when fully loaded with recording paper.
Do not touch the plate (9) on the left side of the standard input
tray.
kg when fully loaded with recording paper.
Do not touch the plate (9) on the left side of the standard input
tray.
95
KX-MB3030RU
8.1.3.
Documents the Unit Can Send
8.1.3.1.
Using the scanner glass
Note:
• Confirm that there are no documents in the automatic document feeder.
• Place the original onto the scanner glass gently. To avoid malfunction, do not press down too firmly.
• If the original is a thick book, do not close the document cover.
• Confirm that any ink, paste or correction fluid has dried completely.
• Effective scanning area is shown by the shaded area:
• Place the original onto the scanner glass gently. To avoid malfunction, do not press down too firmly.
• If the original is a thick book, do not close the document cover.
• Confirm that any ink, paste or correction fluid has dried completely.
• Effective scanning area is shown by the shaded area:
Effective scanning area
8.1.3.2.
Using the auto document feeder
Note:
• Confirm that there are no documents on the scanner glass.
• Confirm that any ink, paste or correction fluid has dried completely.
• Remove clips, staples or other fasteners.
• Do not insert the following types of documents: (Make a copy of the document using the scanner glass and set the copy instead.)
• Confirm that any ink, paste or correction fluid has dried completely.
• Remove clips, staples or other fasteners.
• Do not insert the following types of documents: (Make a copy of the document using the scanner glass and set the copy instead.)
- Chemically treated paper such as carbon or carbonless duplicating paper
- Electrostatically charged paper
- Badly curled, creased or torn paper
- Paper with a coated surface
- Paper with printing on the opposite side that can be seen through the other side, such as newsprint
- Electrostatically charged paper
- Badly curled, creased or torn paper
- Paper with a coated surface
- Paper with printing on the opposite side that can be seen through the other side, such as newsprint
• The total height of the documents when laid flat, must be less than 5 mm. If the documents exceed the capacity of the automatic
document feeder, they may fall or cause a jam in the feeder.
• To set a document with a width of less than 210 mm, we recommend using the scanner glass to copy the original document onto
A4 or letter-size paper, then setting the copied document for better results.
• Do not set documents that do not satisfy the requirements of size and weight. Make a copy of the document using the scanner
glass and set the copy.
• Available document size, document weight and effective scanning area are as follows:
• Shaded area will be scanned.
• When using the unit as a scanner, the effective scanning length depends on the selected paper size.
• When using the unit as a scanner, the effective scanning length depends on the selected paper size.
96
KX-MB3030RU
8.1.4.
Replacing the Toner Cartridge and the Drum Unit
The supplied toner cartridge is a starter toner cartridge.
Caution:
Caution:
• Read the following instructions before you begin installation. After you have read them, open the drum cartridge pro-
tective bag. The drum cartridge contains a photosensitive drum. Exposing it to light may damage the drum. Once you
have opened the protective bag:
— Do not expose the drum cartridge to light for more than 3 minutes.
— Do not touch or scratch the black drum surface inside of the drum cartridge.
— Do not place the drum cartridge near dust or dirt, or in a high humidity area.
— Do not expose the drum cartridge to direct sunlight.
have opened the protective bag:
— Do not expose the drum cartridge to light for more than 3 minutes.
— Do not touch or scratch the black drum surface inside of the drum cartridge.
— Do not place the drum cartridge near dust or dirt, or in a high humidity area.
— Do not expose the drum cartridge to direct sunlight.
• Do not leave the toner cartridge out of the protective bag for a long time. It will decrease the toner life.
• We cannot be responsible for any damage to the unit or degradation of print quality which may occur from the use of a
• We cannot be responsible for any damage to the unit or degradation of print quality which may occur from the use of a
non-Panasonic toner and drum cartridge.
• Do not add toner to the toner cartridge.
1.
Remove the toner cartridge (1) and drum cartridge (2) from the protec-
tive bags.
tive bags.
2.
Shake the toner cartridge horizontally more than 5 times.
3.
Detach the protective cover (3) from the toner cartridge, and remove
the protective sheet (4) from the drum cartridge.
the protective sheet (4) from the drum cartridge.
• Do not touch or scratch the black drum or toner surfaces.
4.
Insert the toner cartridge (5) into the drum cartridge (6) from the upper
angle.
angle.
Click on the first or last page to see other KX-MB3030RU / KX-FAP106A7 service manuals if exist.