Panasonic DP-2500 Service Manual ▷ View online
45
(11) 3 Silver Screws (B1).
(12) 1 Silver Screw (556).
(13) Remove the Left Rear Cover (517) and the Right
(13) Remove the Left Rear Cover (517) and the Right
Rear Cover (507).
(14) 2 Silver Screws (B1).
(15) Remove the Rear Platen Cover (504).
(15) Remove the Rear Platen Cover (504).
(16) Open the Front Cover (528).
(17) 2 Screws (19).
(18) Remove the Front AC SW Cover (534).
(17) 2 Screws (19).
(18) Remove the Front AC SW Cover (534).
(19) Remove the Blind Cover (530).
(11)
(13)
(13)
(12)
(14)
(15)
(16)
(17)
(18)
(19)
46
(20) 3 Screws (19).
(21) Remove the Lower Control Panel Cover (526).
(21) Remove the Lower Control Panel Cover (526).
(22) 1 Screw (19).
(23) Remove the Right Front Cover (525).
(23) Remove the Right Front Cover (525).
(24) Remove the Door Cover Spring (536) and the
Front Cover (528).
Note:
Note:
Exercise care not to lose the Door Cover Spring.
(25) If installed, remove the Inner Tray (1522).
(26) 2 Screws (19).
(27) Remove the S Inner Cover (524).
(26) 2 Screws (19).
(27) Remove the S Inner Cover (524).
(20)
(20)
(21)
(22)
(23)
(24)
(26)
(26)
(27)
(25)
47
(28) Open the Right Cover (1201) Assembly.
Note:
If the Dual-Path Exit Guide Unit (DA-FK200) is
installed, remove it first by reversing the
installation procedure. (See Sect. 9.16., P.526)
installed, remove it first by reversing the
installation procedure. (See Sect. 9.16., P.526)
(29) 3 Silver Screws (B1).
(30) Remove the Right Side Cover (523).
(30) Remove the Right Side Cover (523).
(31) Remove the Fuser Unit. (See Sect. 2.2.8., P.77)
(32) 3 Screws (19).
(32) 3 Screws (19).
(33) Release 2 Latch Hooks in the upper corners of the
Exit Cover and remove the Exit Cover (1521).
(34) 2 Silver Screws (556).
(35) 2 Silver Screws (B1)
(36) Remove the Left Side Cover (535).
(35) 2 Silver Screws (B1)
(36) Remove the Left Side Cover (535).
(29)
(30)
(28)
(29)
(32)
(32)
(32)
(32)
(33)
(34)
(35)
(36)
48
2.2.3.
Inverter, PNL1 PC Board, PNL2 PC Board, LCD Module, Touch Panel, PNL3 PC
Board, Slide Switch Lever
Board, Slide Switch Lever
(1) Remove the Control Panel Assembly
(2) Disconnet Connectors CN1 and CN2 on the
(2) Disconnet Connectors CN1 and CN2 on the
Inverter (125).
(3) Remove the Inverter Holder (113) Assembly.
(4) Remove the Inverter (125).
(5) Disconnect the Flat Cables from Connectors
CN61, CN66 and CN67 on the PNL1 PC Board.
(6) Release the Connector Lock on CN63 and
disconnect the Flat Cable.
(7) 4 Screws (7B).
(8) Remove the PNL1 PC Board (19120).
(8) Remove the PNL1 PC Board (19120).
(2)
(2)
(3)
(4)
(5)
(5)
(6)
(7)x4
(8)
Click on the first or last page to see other DP-2500 service manuals if exist.