DOWNLOAD Panasonic DP-2500 Service Manual ↓ Size: 55.27 MB | Pages: 127 in PDF or view online for FREE

Model
DP-2500
Pages
127
Size
55.27 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / DIGITAL
File
dp-2500.pdf
Date
PREV: Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) Service Manual

Panasonic DP-2500 Service Manual ▷ View online

33
Printer Motor (901)
Clutch (1260)
Lift AC Motor (1152)
Tray Cover (1204)
Sheet Bypass Paper Length Sensor (1045)
Fan (1126)
Fuser Lamps (1043 & 1044)
Separation (1047)
Thermistor Assembly 1 & 2
(1041 & 1042)
Exit Roller (1028)
Thermal Fuse (1040)
Thermostat (1038)
Micro Switch (461)
LSU (1124)
Open Right Cover (1201) Assembly
Bias Transfer Roller (1221)
Registration Pinch Roller
(1222)
Roller Cleaner (1229)
Fuser Unit
Fuser Upper Cover (1002)
Lower Fuser Cover (1003)
Registration Roller (1121)
Toner Sensor (1123)
Registration Sensor (1045)
Paper Level Sensor (1045)
NP Sensor (1045)
Paper Feed Roller (1144)
Reverse Clutch (1132)
C25 Gear Roller (1145)
Spring A (1146)
Feed Roller (1244)
Separator Holder Pad (1242)
Bottom Plater Sensor (1045)
NP Sensor (1045)
Process Toner Cartridge 
Sensor(1045)
2-2-7
2-2-8
2-2-9
Open Right Cover (1201) Assembly
Pressure Roller (1027)
E40 Heat Roller Gear (1014)
Insulation Bushing (1006)
Fuser Roller (1026)
Bearing (1046)
Turn the Power Switch OFF
Open Front Cover (528)
Waste Toner Box
Toner Cartridge
Open Right Cover (1201) Assembly
Process Assembly 
Waste Toner Chamber (704)
OPC Drum (718)
Bias Charge Roller (703)
Cleaning Blade Assembly (717)
Front Cleaning Felt (722)
Rear Cleaning Felt (723)
Cleaning Sponge (724)
Scoop Sheet (725)
Mag Roller (769)
Gap Roller (746)
Dr Blade (762)
Development Felt (774)
Mag Roller Joint (753)
34
2.2.
Disassembly Instructions
2.2.1.
ADF Roller, Pre-Feed Roller, Torque Limiter Bushing, Torque Limiter Spring,
Separation Roller, ADF PC Board, ADF Motor, Solenoid Bracket, 
Reversing Guide 2 Bracket Assembly, Reversing Guide 1 Bracket Assembly, 
Stamp Solenoid, Feed 2 Roller
(1) 1 Screw (19).
(2) Remove the CN Cover (510).
(3) Disconnect the ADF Harness (1935) Connector.
(4) Remove 2 Hinge Covers (1656).
Note:
When re-installing the Hinge Covers, make sure
that the Hinge Film (1658) on each side is inside
of the Hinge Covers.
(5) 1 Screw (19).
(6) Open the ADF.
(7) 2 Screws (F7).
2 Thumb Screws (1654).
(8) Remove the ADF / iADF.
(2)
(1)
(3)
(4)
(6)
(5)
(7)
(7)
35
(9) Open the ADF Cover (1831).
(10) 4 Silver Screws (B1).
(11) Lift the ADF Input Tray (1604).
(12) Slightly pull the right edge of the ADF Rear Cover
upward.
(13) Release the Latch Hooks.
(14) Remove the ADF Rear Cover (1601).
(15) Lower the ADF Input Tray back in place.
(16) Disconnect the AMT Harness (1936) from the
Clutch.
(17) Remove the Snap Ring (B9).
(18) Remove the ADF Roller (1728) Assembly.
(19) Remove the Snap Ring (B9).
(20) Remove the Clutch (1260).
(21) Remove the Bushing (1621).
(22) Remove the Rear ADF Guide (1725).
(9)
(10)
(10)
(11)
(12)
(14)
(13)
(13)
(16)
(17)
(18)
(22)
(21)
(20)
(19)
36
(23) Remove 2 Snap Rings (B9).
(24) Remove the Pin (1781).
(25) Remove the ADF Shaft (1724).
(26) Remove the ADF Roller (1728).
(27) Remove 2 Snap Rings (271).
(28) Remove the Pre-Feed Roller Shaft (1730).
(29) Remove the Pre-Feed Roller (1731).
(30) Remove the ADF Input Tray (1604).
Note:
Do not cut the Tie-Wrap. Push the release clip
on the side to remove it.
(31) 4 Screws (19).
(32) Remove the Upper ADF Guide (1723).
(33) Remove the Snap Ring (271).
(34) Remove the Torque Limiter Bushing (1741) and
Torque Limiter Spring (1742).
(35) Remove the Separation Roller (1740).
(36) Disconnect the APNT Harness (1941) and remove
Sensor (1045) (Original Detection Sensor).
(23)
(23)
(24)
(25 )
(26)
(28)
(27)
(29)
(27)
(32)
(31)
(30)
(31)
(34)
(35)
(36)
(33)
Page of 127
Display

Click on the first or last page to see other DP-2500 service manuals if exist.

RANDOM: