Panasonic DP-2500 Service Manual ▷ View online
37
(37) Disconnect all Connectors on the ADF PC Board.
(38) 2 Screws (19).
(39) Remove the ADF PC Board (19115).
(38) 2 Screws (19).
(39) Remove the ADF PC Board (19115).
(40) Disconnect the AMT Harness (1936) from the
ADF Motor.
(41) Remove the Harness from the 3 clamps.
Note:
Do not cut the Tie-Wrap. Push the release clip
on the side of the Tie-Wrap to remove it.
on the side of the Tie-Wrap to remove it.
(42) 6 Screws (19).
(43) Remove the Sensor Bracket (1663).
(44) Disconnect the B1S Harness (1940) and remove
(43) Remove the Sensor Bracket (1663).
(44) Disconnect the B1S Harness (1940) and remove
Sensor (1045) (ADF Cover Open Detection
Sensor).
Sensor).
(45) 4 Screws (19).
(46) Remove the Motor Bracket (1811) and Gear
(46) Remove the Motor Bracket (1811) and Gear
Bracket (1802) Assemblies.
Note:
Note:
Apply Molykote EM-50L Grease to all Gears
and Shafts except to the following: E26S35
Drive Gear (1805), E26S35 Gear F (3605), ADF
Motor (1801), and the shafts of Drive Shaft 2
(1817) and Exit Roller (1751).
and Shafts except to the following: E26S35
Drive Gear (1805), E26S35 Gear F (3605), ADF
Motor (1801), and the shafts of Drive Shaft 2
(1817) and Exit Roller (1751).
(47) 2 Screws (24).
(48) Remove the ADF Motor (1801).
(48) Remove the ADF Motor (1801).
(38)
(37)
(37)
(39)
(40)
(40)
(41)
(41)
(42)
(42)
(44)
(44)
(43)
(44)
(46)
(45)
(45)
(47)
(48)
38
(49) 1 Silver Screw (B1).
(50) Remove the ADF Front Cover (1637).
(50) Remove the ADF Front Cover (1637).
Note:
Release 3 Latch Hooks in alphabetical order
and in the direction as shown by each arrow.
and in the direction as shown by each arrow.
< When the iADF is installed >
(51) Disconnect 3 CLT Harness (1938) Connectors.
(52) 1 Screw (19).
(53) Remove the Solenoid Bracket (1761) Assembly.
(52) 1 Screw (19).
(53) Remove the Solenoid Bracket (1761) Assembly.
(54) Remove the Spring (1776).
(55) 1 Screw (19).
(56) Remove the Moving Gear Bracket (1768)
(55) 1 Screw (19).
(56) Remove the Moving Gear Bracket (1768)
Assembly.
(57) 1 Screw (19).
(58) Remove the Reversing Guide 2 Bracket (1775)
(58) Remove the Reversing Guide 2 Bracket (1775)
Assembly.
(49)
A.
B.
C.
(50)
(51)
(53)
(51)
(52)
(54)
(56)
(55)
(58)
(57)
39
(59) 10 Screws (B4).
(60) Remove the ADF Unit.
(60) Remove the ADF Unit.
(61) 1 Screw (19).
(62) Remove the Stamp Solenoid (1635).
(63) 2 Screws (19).
(64) Remove the Upper Feed Guide (1861) Assembly.
(62) Remove the Stamp Solenoid (1635).
(63) 2 Screws (19).
(64) Remove the Upper Feed Guide (1861) Assembly.
(65) Carefully turn the ADF Unit upside down.
(66) 1 Screw (19).
(67) Remove the Reversing Guide 1 Spring (1771).
(68) Remove the Reversing Guide 1 Bracket (1772)
(66) 1 Screw (19).
(67) Remove the Reversing Guide 1 Spring (1771).
(68) Remove the Reversing Guide 1 Bracket (1772)
Assembly.
(69) Disconnect the AMT Harness (1936) from the
Clutch.
(70) Remove the Snap Ring (B9).
(71) Remove the Clutch (1260).
(72) Remove 2 Snap Rings (B9).
(73) Remove the Feed 2 Roller (1753).
(74) Open the ADF Exit Cover (1854) Assembly and
(71) Remove the Clutch (1260).
(72) Remove 2 Snap Rings (B9).
(73) Remove the Feed 2 Roller (1753).
(74) Open the ADF Exit Cover (1854) Assembly and
remove in the direction of the arrow.
(59)
(59)
(59)
(59)
(60)
(59)
(62)
(64)
(63)
(61)
(68)
(66)
(67)
(73)
(72)
(72)
(74)
(71)
(69)
(70)
40
(75) Remove the EXT Harness (1943) from 4 Clamps.
(76) 2 Screws (19).
(77) Remove the Feed 2 Roller Guide (1754)
(76) 2 Screws (19).
(77) Remove the Feed 2 Roller Guide (1754)
Assembly.
Note 1:
When re-installing the Feed 2 Roller Guide, make
sure that the Feed 2 Roller Guide is inside of the
hook on the Front ADF Bracket.
sure that the Feed 2 Roller Guide is inside of the
hook on the Front ADF Bracket.
Note 2:
When re-installing the Clutch, make sure that the
hook of the Clutch is properly placed into the notch
of the Rear ADF Bracket.
hook of the Clutch is properly placed into the notch
of the Rear ADF Bracket.
(78) 1 Screw (19).
(76)
(77)
(76)
(75)
(78)
Click on the first or last page to see other DP-2500 service manuals if exist.