Panasonic DP-2500 Service Manual ▷ View online
41
(79) Disconnect the Connector from the Sensor.
(80) Release the Latch Hooks and remove the Sensor
(80) Release the Latch Hooks and remove the Sensor
(Eject Sensor) (1045).
Note:
Note:
Do not break the Latch Hooks when removing
or re-installing the Sensor.
or re-installing the Sensor.
(81) 1 Screw (19).
(82) Disconnect the Connector from the Sensor.
(82) Disconnect the Connector from the Sensor.
(83) Remove the Sensor C Actuator (1756).
(84) Release the Latch Hooks and remove the Sensor
(84) Release the Latch Hooks and remove the Sensor
(Duplex Eject Sensor) (1045).
Note:
When re-installing the EXT Harness (1943), make
sure to route the Harness along the hooks as
illustrated to prevent paper jams.
sure to route the Harness along the hooks as
illustrated to prevent paper jams.
(80)
(79)
(81)
(82)
(84)
(83)
42
< Removing ADF Cover Assembly>
(1) Open the ADF Cover (1831).
(2) Remove the ADF Rear Cover (1601) and the ADF
(2) Remove the ADF Rear Cover (1601) and the ADF
Front Cover (1637). (See step (14) on P.32 and
step (50) on P.35)
step (50) on P.35)
(3) Lower the ADF Input Tray back in place.
(4) Move the Lower Feed Guide (1873) Assembly in
(4) Move the Lower Feed Guide (1873) Assembly in
the direction of the arrow.
(5) Release the hooks on both sides to open the ADF
Cover (1831) Assembly wide.
(6) Remove the Lower Feed Guide (1873) Assembly.
(7) Disconnect the Connector CN29.
(8) Remove the B1S Harness (1940) from 4 Clamps.
(9) Remove the ADF Cover (1831) Assembly.
(8) Remove the B1S Harness (1940) from 4 Clamps.
(9) Remove the ADF Cover (1831) Assembly.
(10) 3 Screws (19).
(11) Remove the Sub ADF Cover (1842) Assembly.
(4)
(5)
(5)
(6)
(8)
(7)
(9)
(8)
(10)
(11)
(10)
43
(12) Disconnect the Connector from the Sensor.
(13) Release the Latch Hooks and remove the Sensor
(13) Release the Latch Hooks and remove the Sensor
(Read Point Sensor) (1045).
Note:
When re-installing the Harness, make sure to route
the Harness along the hooks as illustrated.
the Harness along the hooks as illustrated.
< Cleaning ADF Roller, Pre-Feed Roller, Drive Roller
and Feed 2 Roller>
(1) Open the ADF Cover (1831).
(2) Clean the ADF Roller (1728), Pre-Feed Roller
(2) Clean the ADF Roller (1728), Pre-Feed Roller
(1731), Drive Roller (1872) and the Feed 2 Roller
(1753) with a soft cloth, saturated with isopropyl
alcohol.
(1753) with a soft cloth, saturated with isopropyl
alcohol.
< Cleaning Exit Roller and Inverting Feed Roller>
(3) Lift the ADF Input Tray (1604).
(4) Open the ADF Exit Cover (1854).
(5) Clean the Exit Roller (1751) and the Inverting
(4) Open the ADF Exit Cover (1854).
(5) Clean the Exit Roller (1751) and the Inverting
Feed Roller (1853) with a soft cloth, saturated with
isopropyl alcohol.
isopropyl alcohol.
(12)
(13)
(1)
(3)
(4)
44
2.2.2.
Left Platen Cover, Right Platen Cover, Control Panel Assembly, Lower Rear Cover,
Left Rear Cover, Right Rear Cover, Rear Platen Cover, Front AC SW Cover, Blind
Cover, Lower Control Panel Cover, Right Front Cover, Front Cover, S Inner Cover,
Exit Cover, Left Side Cover, Right Side Cover
Left Rear Cover, Right Rear Cover, Rear Platen Cover, Front AC SW Cover, Blind
Cover, Lower Control Panel Cover, Right Front Cover, Front Cover, S Inner Cover,
Exit Cover, Left Side Cover, Right Side Cover
(1) Slide out the Paper Tray.
(2) 6 Silver Screws (B1).
(3) Remove the Left Platen Cover (514) and the Right
(3) Remove the Left Platen Cover (514) and the Right
Platen Cover (516).
(4) 2 Silver Screws (B1).
(5) Slightly lift the Main Panel Assembly and disconnect
(5) Slightly lift the Main Panel Assembly and disconnect
Connector CN65 on the PNL1 PC Board (19120).
(6) Disconnect the Ground Connector CN68 on the
PNL1 PC Board (19120).
(7) Remove the Control Panel Assembly.
(8) 3 Silver Screws (B1).
(9) Release 3 Latch Hooks on the left and right edge of
(9) Release 3 Latch Hooks on the left and right edge of
the Lower Rear Cover.
(10) Remove the Lower Rear Cover (506).
(1)
(2)
(2)
(3)
(3)
(4)
(7)
(5)
(6)
(8)
(9)
(10)
Click on the first or last page to see other DP-2500 service manuals if exist.