Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) Service Manual ▷ View online
Order Number: MGCS040801C0
H21
Digital Imaging Systems
DP-2310/3010
DP-2330/3030
DP-2330/3030
[ Version 2.1 ]
This service information is designed for experienced repair technicians only and is not intended for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
WARNING
2
The contents of this Service Manual and the Specifications are
subject to change
without notice.
Panasonic Communications Co., Ltd. reserves the right to make improvements in
the product design without reservation and without notice.
Published in Japan.
Panasonic Communications Co., Ltd. reserves the right to make improvements in
the product design without reservation and without notice.
Published in Japan.
Information regarding Lead-Free (PbF) solder:
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a mark following
the PCB part numbers in a label on the PCB.
the PCB part numbers in a label on the PCB.
Caution:
Pb free solder has a higher melting point than standard solder; typically
the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron
with temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too long
to prevent solder splash or damage to the PCB.
Pb free solder will tend to splash when heated too high (about 1100 F/600 C).
ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:
the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron
with temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too long
to prevent solder splash or damage to the PCB.
Pb free solder will tend to splash when heated too high (about 1100 F/600 C).
ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:
URL:
http://www.senju-m.co.jp
) is recommended when repairing PbF PCBs.
This Product Uses Lead (Pb) Free Solder Printed Circuit
Boards (PCBs).
Boards (PCBs).
3
Important Notice
Please read this notice completely BEFORE installing any
optional accessories. As failure to properly install the additional
board or connector with the power ON (only the front power
switch Off) could damage the copier's SPC or SC board.
Please follow the instructions below:
1. It is essential that you turn OFF power to the Main Power
Switch located in the rear of the copier.
2. It is essential that you unplug the Main AC Power Cord from
the wall outlet.
3. Please carefully read the installation instructions and follow
each step.
<Example: DP-2330/3030>
Note:
If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from being
performed (similar to Windows OS when the power is abruptly interrupted), it is
important to follow the step sequence below when turning OFF the Power Switches on
the machine.
performed (similar to Windows OS when the power is abruptly interrupted), it is
important to follow the step sequence below when turning OFF the Power Switches on
the machine.
1. Turn the Power Switch on the Left Side of the machine to the OFF position first.
2. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk
2. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk
Drive Unit.
3. Turn the Main Power Switch on the Back of the machine to the OFF position.
(This interrupts all the power to the machine)
4. Unplug the AC Power Cord.
* The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves
the right to make improvements in the product design without reservation and without notice.
4
<Beispiel: DP-2330/3030>
Hinweis:
