Panasonic TH-103PF12W / TH-103PF12T Service Manual ▷ View online
41
TH-103PF12W / TH-103PF12T
9.31. Removal of C2-Board (lower)
1. Remove the Reinforcement Angle (lower_left).
(Refer to Removal of SS3-Board)
2. Remove the flexible cables from the connectors (C20,
C21).
3. Remove 6 screws ( ) and then remove the flexible
cables from the connectors (CA3, CA4, CA5).
4. Remove 6 screws ( ) and then remove C2-Board (lower).
9.32. Removal of C3-Board (lower)
1. Remove 4 screws and then remove the Rear Cover
Angles (H).
2. Remove 3 screws ( ).
3. Remove 2 screws ( ) and then remove the Rear Cover
3. Remove 2 screws ( ) and then remove the Rear Cover
Angle (lower_center).
4. Remove 2 screws ( ).
5. Remove 2 screws ( ) and then remove the Reinforce-
5. Remove 2 screws ( ) and then remove the Reinforce-
ment Angle (lower_center).
6. Remove the flexible cables from the connectors (C30,
C31, C32).
7. Remove 6 screws ( ) and then remove the flexible
cables from the connectors (CA6, CA7, CA8).
8. Remove 6 screws ( ) and then remove C3-Board (lower).
9.33. Removal of C4-Board (lower)
42
TH-103PF12W / TH-103PF12T
1. Remove the Reinforcement Angle (lower_center).
(Refer to Removal of C3-Board (lower))
2. Remove the flexible cables from the connectors (C40,
C41, C42).
3. Remove 6 screws ( ) and then remove the flexible
cables from the connectors (CA9, CA10, CA11).
4. Remove 6 screws ( ) and then remove C4-Board (lower).
9.34. Removal of C5-Board (lower)
1. Remove the Reinforcement Angle (lower_right).
(Refer to Removal of SD-Board)
2. Disconnect the connector (C55).
3. Remove the flexible cables from the connectors (C50,
3. Remove the flexible cables from the connectors (C50,
C51).
4. Remove 6 screws ( ) and then remove the flexible
cables from the connectors (CA12, CA13, CA14).
5. Remove 6 screws ( ) and then remove C5-Board (lower).
9.35. Removal of C6-Board (lower)
1. Remove the Reinforcement Angle (lower_right).
(Refer to Removal of SD-Board)
2. Remove the flexible cable from the connector (C61).
3. Remove 4 screws ( ) and then remove the flexible
3. Remove 4 screws ( ) and then remove the flexible
cables from the connectors (CA15, CA16).
4. Remove 4 screws ( ) and then remove C6-Board (lower).
9.36. Removal of AC Inlet
43
TH-103PF12W / TH-103PF12T
1. Remove 2 screws and then remove AC Inlet Cover.
2. Disconnect the connector (P9).
3. Remove 3 screws and then remove the AC Inlet.
3. Remove 3 screws and then remove the AC Inlet.
9.37. Removal of Front Glass, V1,
V3-Board and Cabinet Assy
1. Disconnect the connectors (DS15, P34).
2. Remove 2 screws ( ).
3. Remove 2 screws ( ) and then slide the Side Power Unit
3. Remove 2 screws ( ) and then slide the Side Power Unit
upward.
4. Remove the Side Power Unit.
5. Remove 24 screws and then remove Cabinet Block.
6. Pull the bottom of the Cabinet Block forward and lift.
7. Remove the Cabinet Block.
7. Remove the Cabinet Block.
44
TH-103PF12W / TH-103PF12T
9.37.1. Removal of Front Glass
1. Remove 44 screws and then remove the Fixed Angles
(left, right, upper, lower).
2. Remove the Front Glass.
Note: when fixing Fixed Angle
• Screw on 4 screws (1) firstly.
(Note)
• When removing the Front Glass from Cabinet, there
is a risk of the glass center bending damage.
• Be sure to lift the instruction six positions of the fig-
ure, when remove the Front Glass.
Note: when Cabinet or Front Glass is exchanged
• You need new Aluminum Tape kit when you exchange
the Cabinet or Front Glass.
Note: when Front Glass is exchanged
• Paste the Sponges in order along each Fixed Angles
(left, right, upper, lower).
Note
• The sponges are parts which cannot be recycled. Please
use the new article when you exchange the Front Glass.
Click on the first or last page to see other TH-103PF12W / TH-103PF12T service manuals if exist.