DOWNLOAD Panasonic KX-VC300CX / KX-VC600CX Service Manual ↓ Size: 5.4 MB | Pages: 127 in PDF or view online for FREE

49

Execute "GET_HS_STAT" command in DIAG Mode.
(-Refer to “8.11 DIAG Operation”
 -Audio part Connection Diagram : No7)

- "00" appears when HS_SP/MIC cable is not 

inserted into the jack.

- "10" appears when HS_MIC cable is inserted into 

the jack.

- "01" appears when HS_SP cable is inserted into the 

jack.

- "11" appears when HS_SP/MIC cable is inserted 

into the jack.

 If "11"appears all the time, cable may be discon-
nected. Check again. If the cable is disconnected, 
perform procedures shown in Measures column.

Insert the cable to CN11 on the sub board 
(PNLB1846ZA-A), or CN303 on the HS board 
(PNLB1846ZA-C).

 If the above does not apply, signal error related to 
HSout_STAT or HS_STAT may have occurred.

[HSout_STAT line]
Check signal changes at specific points on sub board 
(PNLB1846ZA-A) by inserting and removing headset 
SP terminal.

-  Pin 4 of CN11: If the voltage is not 3 V or higher 

when HS_SP cable is inserted and if the voltage is 
not 0.5 V or less when the cable is not inserted, 
check solder joints at HS board, CN11 and Q1. If 
any defective solder joints are discovered, perform 
procedures a) shown in Measures column.

a) Resolder connector pins.

If failure continues, perform procedures b) shown in 
Measures column.

b) Replace parts C68 and Q5.

- E of Q5: If the voltage is not 0.8 V or less when 

HS_SP cable is inserted and if the voltage is not 3 
V or more when the cable is not inserted, check sol-
der joints at pin 2 on IC24, Q5, and R71. If any 
defective solder joints are discovered, perform pro-
cedures a) shown in Measures column. If failure 
continues, perform procedures c) shown in Mea-
sures column.

c) Replace parts Q5, R71, and others.

-  E of Q16: If the voltage is not 3 V or more when 

HS_SP cable is inserted and if the voltage is not 
0.8 V or less when the cable is not inserted, check 
solder joints at Q16 to pin 7 on CN3. If any defec-
tive solder joints are discovered, perform proce-
dures a) shown in Measures column. If failure 
continues, perform procedures d) shown in Mea-
sures column.

d) Replace part Q16, check the pin 124 of IC121 on 

the main board.

[HS_STAT line]
Check signal changes at specific points on sub board 
(PNLB1846ZA-A) by inserting and removing headset 
MIC terminal.

- Pin 5 of CN11: If the voltage is not 3 V or more 

when HS_MIC cable is inserted into the jack and if 
the voltage is not 0.5 V or less when the cable is 
not inserted, check solder joints at HS board, CN11 
and Q1. If any defective solder joints are discov-
ered, perform procedures a) shown in Measures 
column.

If failure continues, perform procedures e) shown in 
Measures column.

e) Replace parts C22 and Q1.

50

- E of Q1: If the voltage is not 0.8 V or less when 

HS_MIC cable is inserted and if the voltage is not 3 
V or more when the cable is not inserted, check sol-
der joints at IC15 and 16, Q1, and R27. If any 
defective solder joints are discovered, perform pro-
cedures a) shown in Measures column. If failure 
continues, perform procedures f) shown in Mea-
sures column.

f) Replace parts Q1, R27 and others.

- E of Q15: If the voltage is not 3 V or more when 

HS_MIC cable is inserted and if the voltage is not 
0.8 V or less when the cable is not inserted, check 
solder joints at Q15 to pin 2 on CN3. If any defec-
tive solder joints are discovered, perform proce-
dures a) shown in Measures column. If failure 
continues, perform procedures g) shown in Mea-
sures column.

g) Replace part Q15, check the pin 123 of IC121 on 

the main board.

Sub board (PNLB1846ZA-A) may be damaged. 
Replace the damaged board with a working one and 
check if sound is available.
- If it is, perform procedures shown in Measures col-

umn.

See Sub Board Troubleshooting.

Check power and clock on main board 
(PNLB1845ZB). Refer to (8.10. Power/clock Failure).

Refer to (8.10. Power/clock Failure).

Execute "TEST_AMIC_START" command in DIAG 
Mode. (Wait until OK appears)
(-Refer to “8.11 DIAG Operation”
 -Audio part Connection Diagram : No7)
Check if the audio from A-MIC is transmitted to Audio 
pin jack output terminal. Check with oscilloscope, 
connect SP/TV monitor to Audio pin jack output and 
check by listening, or only connect a headset SP and 
check by listening.

If no sound is available, there may be errors on the 
signal path either at pin 4 and 7 of CN6, IC12, IC15 
and 16, IC19, CN3 on the sub board or at pin 8 of 
CN505, pin 130 of IC121 on the main board.
- Confirm that there are no solder bridges or unsol-

dered parts on the circuit mentioned above.
If any defective solder joints are discovered, per-
form procedures a) shown in Measures column.

- Check if AC waveform is observed at pin 1 and 2 of 

IC19.
Check spread of signal from each IC's input/output, 
and perform procedures b) in Measures column if 
there is disconnected area.

Execute "TEST_AMIC_STOP" command and quit 
DIAG Mode.

a) Resolder connector pins.
b) Replace peripheral parts on the defective circuit.

Replace the main board if there are no errors, but 
communication is still not available.

Cable between main and sub board may be discon-
nected. Check visually.
If the cable is disconnected, perform procedures 
shown in Measures column.

Insert the cable to CN3 on the sub board 
(PNLB1846ZA-A), or CN505 on the main board 
(PNLB1845ZB).

Cable may be disconnected at sub board 
(PNLB1846ZA-A) or/and HS board (PNLB1846ZA-
C). Check visually.
If the cable is disconnected, perform procedures 
shown in Measures column.

Insert the cable to CN11 on the sub board 
(PNLB1846ZA-A), or CN303 on the HS board 
(PNLB1846ZA-C).

51

Execute "GET_HS_STAT" command in DIAG Mode.
(-Refer to “8.11 DIAG Operation”
 -Audio part Connection Diagram : No8)

- "00" appears when HS_SP/MIC cable is not 

inserted into the jack.

- "10" appears when HS_MIC cable is inserted into 

the jack.

- "01" appears when HS_SP cable is inserted into the 

jack.

"11" appears when HS_SP/MIC cable is inserted into 
the jack.

If "11"appears all the time, cable may be discon-
nected. Check again. If the cable is disconnected, 
perform procedures shown in Measures column.

Insert the cable to CN11 on the sub board 
(PNLB1846ZA-A), or CN303 on the HS board 
(PNLB1846ZA-C).

If the above does not apply, signal error related to 
HSout_STAT or HS_STAT may have occurred.

[HSout_STAT line]
Check signal changes at specific points on sub board 
(PNLB1846ZA-A) by inserting and removing headset 
SP terminal.

- Pin 4 of CN11: If the voltage is not 3 V or higher 

when HS_SP cable is inserted and if the voltage is 
not 0.5 V or less when the cable is not inserted, 
check solder joints at HS board, CN11 and Q1. If 
any defective solder joints are discovered, perform 
procedures a) shown in Measures column.

a) Resolder connector pins.

If failure continues, perform procedures b) shown in 
Measures column.

b) Replace parts C68 and Q5.

- E of Q5: If the voltage is not 0.8 V or less when 

HS_SP cable is inserted and if the voltage is not 3 
V or more when the cable is not inserted, check sol-
der joints at pin 2 on IC24, Q5, and R71. If any 
defective solder joints are discovered, perform pro-
cedures a) shown in Measures column. If failure 
continues, perform procedures c) shown in Mea-
sures column.

c) Replace parts Q5, R71, and others.

- E of Q16: If the voltage is not 3 V or more when 

HS_SP cable is inserted and if the voltage is not 
0.8 V or less when the cable is not inserted, check 
solder joints at Q16 to pin 7 on CN3. If any defec-
tive solder joints are discovered, perform proce-
dures a) shown in Measures column. If failure 
continues, perform procedures d) shown in Mea-
sures column.

d) Replace part Q16, check the pin 124 of IC121 on 

the main board.

[HS_STAT line]
Check signal changes at specific points on sub board 
(PNLB1846ZA-A) by inserting and removing headset 
MIC terminal.

- Pin 5 of CN11: If the voltage is not 3 V or more 

when HS_MIC cable is inserted into the jack and if 
the voltage is not 0.5 V or less when the cable is 
not inserted, check solder joints at HS board, CN11 
and Q1. If any defective solder joints are discov-
ered, perform procedures a) shown in Measures 
column.

If failure continues, perform procedures e) shown in 
Measures column.

e) Replace parts C22 and Q1.

52

- E of Q1: If the voltage is not 0.8 V or less when 

HS_MIC cable is inserted and if the voltage is not 3 
V or more when the cable is not inserted, check sol-
der joints at IC15 and 16, Q1, and R27. If any 
defective solder joints are discovered, perform pro-
cedures a) shown in Measures column. If failure 
continues, perform procedures f) shown in Mea-
sures column.

f) Replace parts Q1, R27 and others.

- E of Q15: If the voltage is not 3 V or more when 

HS_MIC cable is inserted and if the voltage is not 
0.8 V or less when the cable is not inserted, check 
solder joints at Q15 to pin 2 on CN3. If any defec-
tive solder joints are discovered, perform proce-
dures a) shown in Measures column. If failure 
continues, perform procedures g) shown in Mea-
sures column.

g) Replace part Q15, check the pin 123 of IC121 on 

the main board.

Sub board (PNLB1846ZA-A) may be damaged. 
Replace the damaged board with a working one and 
check if sound is available.
- If it is, perform procedures shown in Measures col-

umn.

See Sub Board Troubleshooting.

Check power and clock on main board 
(PNLB1845ZB). Refer to (8.10. Power/clock Failure).

Refer to (8.10. Power/clock Failure).

Execute "TEST_AMIC_START" command in DIAG 
Mode. (Wait until OK appears)
(-Refer to “8.11 DIAG Operation”
 -Audio part Connection Diagram : No8)
Check if the audio from A-MIC is transmitted to Audio 
pin jack output terminal. Check with oscilloscope, 
connect SP/TV monitor to Audio pin jack output and 
check by listening, or only connect a headset SP and 
check by listening.
If no sound is available, there may be errors on the 
signal path either at pin 4 and 7 of CN6, IC12, IC15 
and 16, IC19, CN3 on the sub board or at pin 8 of 
CN505, pin 130 of IC121 on the main board.
- Confirm that there are no solder bridges or unsol-

dered parts on the circuit mentioned above.
If any defective solder joints are discovered, per-
form procedures a) shown in Measures column.

- Check if AC waveform is observed at pin 1 and 2 of 

IC19.
Check spread of signal from each IC's input/output, 
and perform procedures b) in Measures column if 
there is disconnected area.

Execute "TEST_AMIC_STOP" command and quit 
DIAG Mode.

a) Resolder connector pins.
b) Replace peripheral parts on the defective circuit. 

Replace the main board if there are no errors, but 
communication is still not available.

Failure on sub board (PNLB1846ZA-A) At CN2, check the voltage of V12D, V5A, V3R3D, 

and TP2 when a 7.4 V microphone is connected.
When monitored on an oscilloscope/multimeter: 
V12D: 11.5 V or more, V5A: 4.5 V or more
V3R3D: 3 V or more, TP2: 7 V or more
If any of the above criteria is not met;
Check solder joints at CN2, L32, L34, and L35 on 
sub board.
If any defective solder joints are discovered, perform 
procedures shown in Measures column.

Resolder connector pins.