Panasonic UE-608030 / UE-608031 / UE-608032 Service Manual ▷ View online
41
2. The pin end stoppers are provided at points along the 450 mm
(1 ft. 5 23/32 in.) adjustment range.
Use them at points in the range from the highest point and at
the point where the elite Panaboard will be stopped by the
stoppers. When the system is to be moved, release the
brake (1) and simultaneously push one pin end stopper (the one
on the brake side) (2) and lower the elite Panaboard slightly.
Then simultaneously push the other pin end stopper and lower
the elite Panaboard to the lowest point.
After lowering the elite Panaboard to the lowest point, pull the
brake lever to secure the board.
(1 ft. 5 23/32 in.) adjustment range.
Use them at points in the range from the highest point and at
the point where the elite Panaboard will be stopped by the
stoppers. When the system is to be moved, release the
brake (1) and simultaneously push one pin end stopper (the one
on the brake side) (2) and lower the elite Panaboard slightly.
Then simultaneously push the other pin end stopper and lower
the elite Panaboard to the lowest point.
After lowering the elite Panaboard to the lowest point, pull the
brake lever to secure the board.
Note:
1. When pushing the pin end stoppers and then moving the
elite Panaboard down to an even lower position, remember
that the projector will also be lowered at the same time.
Take care to prevent the projector from hitting your head or
other parts of your body.
2. Similarly, the up/down part on which the elite Panaboard is
installed will also move down to a low position so exercise
care when tall equipment has been placed on the table
plate.
3. Be careful to avoid pinching your finger in the pin end
stopper hole.
elite Panaboard down to an even lower position, remember
that the projector will also be lowered at the same time.
Take care to prevent the projector from hitting your head or
other parts of your body.
2. Similarly, the up/down part on which the elite Panaboard is
installed will also move down to a low position so exercise
care when tall equipment has been placed on the table
plate.
3. Be careful to avoid pinching your finger in the pin end
stopper hole.
42
5.2.
Moving the Stand (available only for installing Stand)
5.2.1.
Stowing the Projector Assembly
1. Disconnect the power cable from the power outlet.
2. Move the projector.
• While lifting the projector arm slightly, turn it clockwise or
2. Move the projector.
• While lifting the projector arm slightly, turn it clockwise or
counterclockwise slowly, and move the arm so that it is made
parallel with the elite Panaboard unit.
Note:
Note:
At the lowest point, the projector may come into contact with
the unit. Rotate the arm away, so that the projector will not
touch the unit.
the unit. Rotate the arm away, so that the projector will not
touch the unit.
3. Attach knob B (with the board bracket attached) at the position
shown in the figure and secure the projector arm.
4. Lower the elite Panaboard to the lowest point.
shown in the figure and secure the projector arm.
4. Lower the elite Panaboard to the lowest point.
Note:
• If the height of the entrance is less than 2 m (6 ft. 6 3/4 in.),
proceed with steps 1 and 2, and after having moved the
projector, lower the height of the projector arm by following
the steps below.
(1) Attach knob B to the top hole.
(2) Lift the projector arm slightly and remove knob A from the
projector arm. (The position of knob A varies depending
on the projector used.)
(3) Lower the projector arm to the position where knob B
stop it.
(4) Attach removed knob A to the securing position, and
secure the projector arm.
proceed with steps 1 and 2, and after having moved the
projector, lower the height of the projector arm by following
the steps below.
(1) Attach knob B to the top hole.
(2) Lift the projector arm slightly and remove knob A from the
projector arm. (The position of knob A varies depending
on the projector used.)
(3) Lower the projector arm to the position where knob B
stop it.
(4) Attach removed knob A to the securing position, and
secure the projector arm.
43
5.2.2.
Removing Foot Reinforcing Assemblies
While grasping the release lever on the back side of each foot
reinforcing assembly, pull the assembly from the stand base.
reinforcing assembly, pull the assembly from the stand base.
Note:
Before moving the stand, be absolutely sure to remove the
foot reinforcing assemblies from the stand base. If the stand is
moved with these assemblies still attached, it may catch on
surrounding objects, cause somebody to trip over and/or
cause injury.
foot reinforcing assemblies from the stand base. If the stand is
moved with these assemblies still attached, it may catch on
surrounding objects, cause somebody to trip over and/or
cause injury.
44
5.2.3.
Moving Stand
First get somebody to help you. Then take hold of the frame on the
elite Panaboard sides and protective cover of the stand, and move
the stand together.
elite Panaboard sides and protective cover of the stand, and move
the stand together.
Note1:
1. Release the lock lever for each caster.
2. Before moving the stand, disconnect the plug of the table
tap from the wall outlet.
3. Make sure that none of the cables are dragged along with
the stand.
4. Be absolutely sure to have another person ready to help you
move the stand.
5. Take care that none of the equipment placed on the table
plate will fall off.
6. While moving the stand, the stowed projector will move out
of your field of view so while moving the stand, take care not
to allow the projector to bump into a wall, door or other
individuals around you.
2. Before moving the stand, disconnect the plug of the table
tap from the wall outlet.
3. Make sure that none of the cables are dragged along with
the stand.
4. Be absolutely sure to have another person ready to help you
move the stand.
5. Take care that none of the equipment placed on the table
plate will fall off.
6. While moving the stand, the stowed projector will move out
of your field of view so while moving the stand, take care not
to allow the projector to bump into a wall, door or other
individuals around you.
Note2: After finishing the moving
After the stand has been moved, follow the steps below to
return it to the condition in which it was before it was moved.
return it to the condition in which it was before it was moved.
1. Lock the stand’s casters.
2. Turn the casters so that they point inwards.
3. Re-attach the foot reinforcing assemblies
4. Return the knob currently in the hole for securing the
projector arm to the hole on the board bracket.
• If the height of the entrance is less than 2 m (6 ft. 6 3/4 in.),
perform step (1) to (4) in Sec. 5.2.1-4 in reverse.
5. Move the projector in front of the elite Panaboard.
6. Connect the power cord.
7. Readjust the projector as needed and align it with the
screen.
2. Turn the casters so that they point inwards.
3. Re-attach the foot reinforcing assemblies
4. Return the knob currently in the hole for securing the
projector arm to the hole on the board bracket.
• If the height of the entrance is less than 2 m (6 ft. 6 3/4 in.),
perform step (1) to (4) in Sec. 5.2.1-4 in reverse.
5. Move the projector in front of the elite Panaboard.
6. Connect the power cord.
7. Readjust the projector as needed and align it with the
screen.
Click on the first or last page to see other UE-608030 / UE-608031 / UE-608032 service manuals if exist.