Panasonic UE-608030 / UE-608031 / UE-608032 Service Manual ▷ View online
25
4.6.
Mounting Projector Arm
1. Pass the power cable used for the projector and the video cable
through the projector arm.
through the projector arm.
Note:
1. Ensure that the plugs to connect to the projector come out
at the longer end of the projector arm
(the part where the projector is mounted).
2. If the outlet end of the power cable is too large to go through
the projector arm, the projector arm cannot be mounted on
the up/down unit. Pass a length of string (twine) through the
projector arm, and then pass the cable with the string
attached to it through the projector arm after the arm has
been mounted on the up/down unit.
3. It is easier to pass the cables from the side of the Power
Outlet End through the projector arm.
at the longer end of the projector arm
(the part where the projector is mounted).
2. If the outlet end of the power cable is too large to go through
the projector arm, the projector arm cannot be mounted on
the up/down unit. Pass a length of string (twine) through the
projector arm, and then pass the cable with the string
attached to it through the projector arm after the arm has
been mounted on the up/down unit.
3. It is easier to pass the cables from the side of the Power
Outlet End through the projector arm.
2. Decide on the position of the knob provided on the rear on the
projector arm, and fasten it tightly.
projector arm, and fasten it tightly.
Note:
1. The position where the knob is to be secured depends on
the projector which is going to be used.
the projector which is going to be used.
2. Keep the other knob for future use. After all installation work
is finished, attach the knob to an empty hole on the board
bracket (7) on the back of the board.
is finished, attach the knob to an empty hole on the board
bracket (7) on the back of the board.
26
3. Insert the projector arm from above into the pipe holding post of
the up/down frame.
the up/down frame.
• Introduce the ends of the power cable and video cable which
have already been passed through the projector arm into the
pipe holding post, and then insert the projector arm.
have already been passed through the projector arm into the
pipe holding post, and then insert the projector arm.
Note:
When mounting the projector arm, ensure that its end does not
hit anybody or anything in the vicinity.
hit anybody or anything in the vicinity.
4. Mount the projector bracket, on which the projector unit has
been mounted, onto the projector arm
been mounted, onto the projector arm
Note:
The position where the projector is to be mounted depends on
the model which is going to be used. Adjust the distance from
the longer end of the projector arm (the part where the
projector) is mounted) to the projector bracket to what is
indicated below, and secure the projector.
the model which is going to be used. Adjust the distance from
the longer end of the projector arm (the part where the
projector) is mounted) to the projector bracket to what is
indicated below, and secure the projector.
27
5. Tighten up the screw (22) for securing the pipe bracket, and
loosely secure the bracket to the projector arm.
loosely secure the bracket to the projector arm.
6. Route and connect the power cable and video cable, which
have already been passed through the projector arm, to the
projector, and secure the pipe cap (23) using the screw (24)
for securing the pipe cap.
have already been passed through the projector arm, to the
projector, and secure the pipe cap (23) using the screw (24)
for securing the pipe cap.
7. Attach cable holder A (1) to the center wall side of the lift bottom
stay, and route the power cable and video cable so that they
point straight down.
stay, and route the power cable and video cable so that they
point straight down.
Note:
1. Use cable holder B (2) for cable management of the elite
Panaboard and other equipment.
2. Use the hook and loop fastener (3) for cable management
of the computer on the table and cords connected to the
plug adaptor.
Panaboard and other equipment.
2. Use the hook and loop fastener (3) for cable management
of the computer on the table and cords connected to the
plug adaptor.
28
4.7.
Adjusting Up/Down Unit
Align the position of the hold tube assembly, to which the gas
spring is secured, with the elite Panaboard model to be installed,
and set it.
spring is secured, with the elite Panaboard model to be installed,
and set it.
1. Loosely secure the board bottom bracket to the position shown
in the right.
in the right.
• In the state the UB-T880 is shipped, the position where the
board bottom brackets are secured is appropriate when using
the SANYO LP-WXL46(S). The position where the bottom of
the SANYO LP-WXL46(S). The position where the bottom of
the elite Panaboard is to be secured differs depending on the
type of elite Panaboard to be installed.
Note:
The position at which the board bottom bracket is to be fixed
applies to the SANYO LP-WXL46(S) projector.
When any other projector is going to be used, move it from the
position shown in the right by the dimensions given below.
applies to the SANYO LP-WXL46(S) projector.
When any other projector is going to be used, move it from the
position shown in the right by the dimensions given below.
Click on the first or last page to see other UE-608030 / UE-608031 / UE-608032 service manuals if exist.