Panasonic KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 Service Manual ▷ View online
61
U30: Door open
20
00
00
00 1. ADF Door remains open, or
is not closed properly.
Close the door securely.
2. The claw of the Upper
Chassis is broken and does
not interrupt the Door
Sensor.
not interrupt the Door
Sensor.
Replace the Upper Chassis.
3. The claw position is not
matched to the Door
Detector’s position.
Detector’s position.
1. Adjust each part position so that the claw can
interrupt the Door Detector.
4. The Door Detector or its
monitor circuit does not work
correctly.
correctly.
1. Perform the "Key / Sensor" test in
Sec. 10.3.7.
to
check the sensor condition, while repeatedly
closing and opening the door.
closing and opening the door.
2. Check the following connection and soldering
condition on each connector.
CN2003 (DOOR DETECTION Board) to CN19
(CONTROL Board)
CN2003 (DOOR DETECTION Board) to CN19
(CONTROL Board)
3. Check the following soldering condition.
(1) DOOR DETECTION Board
IC2001 and its surrounding circuits
(2) CONTROL Board
Q40, R543, R544, R550, R555
4. Replace faulty parts or boards.
F17: SDRAM
Error
Error
89
01
XX
00 1. Access error to SDRAM
(IC18) on the CONTROL
Board.
Board.
1. Check the soldering condition of the following parts
on the CONTROL Board.
R385 to R406, R411 to R414, R994, R645, IC18
R385 to R406, R411 to R414, R994, R645, IC18
2. Replace faulty parts or board.
F30: FAN Error
94
00
00
00 1. FAN motor is not connected. 1. Check inserted the connecter from FAN motor in
CN22 on the CONTROL Board.
2. Electrical circuit does not
work properly.
1. Check of the fan power supply.
CN22 1st-pin : DC15V over
2. Check the soldering condition of the following
parts.
Q52, Q53, Q54, R580, R581, R670, R575,
R578,R579, D29, R584, R910, R911
Q52, Q53, Q54, R580, R581, R670, R575,
R578,R579, D29, R584, R910, R911
3. Replace faulty parts or board.
4. Replace the FAN.
4. Replace the FAN.
3. Mechanical problem
prevents FAN from rotating.
1. Remove obstacles that prevent the FAN from
rotating.
2. Replace the FAN.
F31: Analogue
IC Error
IC Error
95
XX
00
00 1. Access error to Analogue IC
(IC1) on the CONTROL
Board.
Board.
1. Check the soldering condition of the following parts
and of their surrounding circuits on the CONTROL
Board.
Analogue IC (IC1)
Board.
Analogue IC (IC1)
2. Replace faulty parts or board.
F36: ASIC
SDRAM Error
SDRAM Error
9A
XX
00
00 1. Access error to SDRAM
(IC18)
1. Check the soldering condition of the parts
surrounding the IC9 (PF4).
2. Check the soldering condition of the SDRAM
(IC18).
3. Replace faulty parts or CONTROL Board.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Recommended action
62
F60: Front-side
gain adjustment
error
gain adjustment
error
50
00
00
00 1. The surface of Scanning
Glass (F) is dirty.
1. Clean the surface with a soft and dry cloth.
2. CIS (F) Unit does not work
properly.
1. Execute "Focus" test in
Sec. 10.3.7.
to check the
waveform of CIS output.
2. Execute "CIS LED" test in
Sec. 10.3.7.
to check the
lighting of each RGB.
3. Check the following connections and soldering
condition on each connector.
CIS (F) Unit to CN1 (CONTROL Board)
CIS (F) Unit to CN1 (CONTROL Board)
4. Check the power supply for LED.
(1) CN1-12th pin, F1: 7.0 V
(2) L1, L2, L3, L200, L201, L202, Q3, Q4, Q6,
(2) L1, L2, L3, L200, L201, L202, Q3, Q4, Q6,
Q200, Q201, Q202
5. Replace faulty parts or boards.
3. Problem with Pixel data from
CIS (F) or from image
processing circuit.
processing circuit.
1. Check the connection and soldering condition of
the following parts.
Between CIS (F) and CN1 (CONTROL Board)
Between CIS (F) and CN1 (CONTROL Board)
2. Check the soldering condition of the following parts
and of their surrounding circuits on the CONTROL
Board.
(1) IC9 (FP4)
(2) IC1 (AFE)
(3) IC4 (D/A Conv.)
Board.
(1) IC9 (FP4)
(2) IC1 (AFE)
(3) IC4 (D/A Conv.)
3. Monitor the following CIS Timing signals on the
CN1.
(1) FCLK (CN1-9th pin) : See
(1) FCLK (CN1-9th pin) : See
Fig.11.2.1.
(2) FSP (CN1-11th pin) : See
Fig.11.2.2.
4. Replace faulty parts or boards.
F61: Front-side
black level error
black level error
51
00
00
00 1. Problem with Pixel data from
CIS (F) or from image
processing circuit.
processing circuit.
Refer to F60 - 3.
F62: Back-side
gain adjustment
error
gain adjustment
error
52
00
00
00 1. The surface of Scanning
Glass (B) is dirty.
1. Clean the surface with a soft and dry cloth.
2. CIS (B) Unit does not work
properly.
1. Execute "Focus" test in
Sec. 10.3.7.
to check the
waveform of CIS output.
2. Execute "CIS LED" test in
Sec. 10.3.7.
to check the
lighting of each RGB.
3. Check the following connections and soldering
condition on each connector.
CIS (B) Unit to CN3 (CONTROL Board)
CIS (B) Unit to CN3 (CONTROL Board)
4. Check the power supply for LED.
(1) CN3-12th pin, F1: 7.0 V
(2) L8, L9, L10, L203, L204, L205, Q9, Q10, Q12,
(2) L8, L9, L10, L203, L204, L205, Q9, Q10, Q12,
Q203, Q204, Q205
5. Replace faulty parts or boards.
3. Problem with Pixel data from
CIS (B) or from image
processing circuit.
processing circuit.
1. Check the connection and soldering condition of
the following parts.
Between CIS (B) and CN3 (CONTROL Board)
Between CIS (B) and CN3 (CONTROL Board)
2. Check the soldering condition of the following parts
and of their surrounding circuits on the CONTROL
Board.
(1) IC9 (FP4)
(2) IC1 (AFE)
(3) IC4 (D/A Conv.)
Board.
(1) IC9 (FP4)
(2) IC1 (AFE)
(3) IC4 (D/A Conv.)
3. Monitor the following CIS Timing signals on the
CN3.
(1) BCLK (CN3-9h pin) : See
(1) BCLK (CN3-9h pin) : See
Fig.11.2.1.
(2) BSP (CN3-11th pin) : See
Fig.11.2.2.
4. Replace faulty parts or boards.
F63: Back-side
black level error
black level error
53
00
00
00 1. Problem with Pixel data from
CIS (B) or from image
processing circuit.
processing circuit.
Refer to F62 - 3.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Recommended action
63
F80: Double
Feed Detector
error
Feed Detector
error
60
00
00
00 1. Double Feed Detector
(Generate) does not work
properly.
properly.
Refer to U23 - 5.
2. Double Feed Detector
(Receive) does not work
properly.
properly.
Refer to U23 - 6.
F82: DAC
control status
error
control status
error
63
00
00
00 1. No reply from DAC IC.
1. Check the soldering condition of CONTROL Board
and its surrounding parts of IC4.
2. Replace faulty parts or boards.
F90: Sub-
processor error
processor error
9E
XX
XX
XX 1. Sub-processor error of
ASIC.
1. Check the soldering condition of CONTROL Board
and its surrounding parts of IC9.
2. Replace faulty parts or boards.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Recommended action
64
Fig.11.2.1.
Fig.11.2.2.
Fig.11.2.3.
CN1-9, CN3-9 Pixel Clock
CN1-11, CN3-11 SP(Start Pulse)
CN12-1 Motor OUT
Click on the first or last page to see other KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 service manuals if exist.