Panasonic NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G Service Manual ▷ View online
5. Installation of Lens Ass'y
Take care not to damage the motor leads.
Install the Lens Ass'y with the 2 Bosses and 2 Screws
(533).
Install the Lens Ass'y with the 2 Bosses and 2 Screws
(533).
Fig. D5
6. Removal of Front Case Ass'y & Bottom Ass'y
1) Disconnect the Front F.P.C. from the Connector FP6.
2) Open the Cassette Cover once and remove the 3
2) Open the Cassette Cover once and remove the 3
Screws (433).
3) Remove the both of the Front Case Ass'y & Bottom
Case Ass'y while gripping it while disconnecting the
Connector B1.
Connector B1.
Fig. D6
Alternative method:
If necessary, the Front Case Ass'y can be removed at first.
If necessary, the Front Case Ass'y can be removed at first.
Boss
Lens Ass'y
FP701
FP301
Boss
Motor leads
FP6
Cassette Cover
Front F.P.C.
B1
Front Case Ass'y & Bottom Case Ass'y
3. Installation of EVF Unit
1) Confirm that the EVF F.P.C. is hooked to the Hooking
Portions on the Bottom.
2) Install the EVF Unit while holding the EVF F.P.C. to
avoid damage of the EVF F.P.C.
Fig. D3
4. Installation of Rear Case Unit
1) Put the connector leads in the space so as not to cover
Portion A.
Fig. D4-1
2) Secure the Locking Tab (L-1) of the Rear Case Unit to
install it.
Fig. D4-2
EVF Unit
FP9 (For model with Color EVF)
or
FP11 (For model with Monochrome EVF)
or
FP11 (For model with Monochrome EVF)
Hooking
Portions
Portions
Hold EVF F.P.C.
P1
Portion A
Rear
Case
Unit
Case
Unit
Connector
leads
leads
(L-1)
(For model with S-VIDEO)
Rear Case Unit
533
45
NV-GS6EE NV-GS6GC
8. Installation of Mechanism Chassis Ass'y
Take care not to damage the F.P.C.s.
1) After installing the Mechanism Chassis Ass'y, confirm
1) After installing the Mechanism Chassis Ass'y, confirm
the F.P.C.s are positioned as shown.
Fig. D8-1
Replacement of Mechanism Chassis Ass'y
When replacing the Main Chassis Ass'y or the Cylinder
Unit, be sure to perform the Envelope Output Adjustment.
Refer to "ENVELOPE OUTPUT ADJUSTMENT" in
MECHANICAL ADJUSTMENT.
When replacing the Main Chassis Ass'y or the Cylinder
Unit, be sure to perform the Envelope Output Adjustment.
Refer to "ENVELOPE OUTPUT ADJUSTMENT" in
MECHANICAL ADJUSTMENT.
Handling Caution of Mechanism Chassis Ass'y
When servicing the Mechanism Chassis Ass'y without the
Cassette Up Unit, do not handle the Sub Chassis of the
Mechanism Chassis Ass'y.
When servicing the Mechanism Chassis Ass'y without the
Cassette Up Unit, do not handle the Sub Chassis of the
Mechanism Chassis Ass'y.
Fig. D8-2
Mechanism Chassis Ass'y
Mechanism Chassis Ass'y
(without Cassette Up Unit)
(without Cassette Up Unit)
<Side View>
Sub Chassis
Sub Chassis
Sub Chassis
7. Installation of Main C.B.A.
Take care not to damage the F.P.C.s.
1) Connect the Zoom Switch F.P.C. to the Connector
1) Connect the Zoom Switch F.P.C. to the Connector
FP10 on the Main C.B.A.
2) Connect the F.P.C.s to the connectors on the Main
C.B.A, verifying that the direction of the Flexible Cables
is correct. Refer to "REMOVAL/INSTALLATION OF
F.P.C. FROM NON ZIF (Zero Insertion Force)
CONNECTOR."
is correct. Refer to "REMOVAL/INSTALLATION OF
F.P.C. FROM NON ZIF (Zero Insertion Force)
CONNECTOR."
3) After installing the Main C.B.A., confirm the F.P.C.s are
positioned as shown.
Fig. D7
Sub Mechanism
F.P.C.
F.P.C.
Capstan
F.P.C.
F.P.C.
Zoom
Switch
F.P.C.
Switch
F.P.C.
Cylinder
F.P.C.
F.P.C.
Head
Amp
F.P.C.
Amp
F.P.C.
Mechanism
F.P.C.
F.P.C.
46
NV-GS6EE NV-GS6GC
11. Removal of Side Case R Unit
Open and rotate the LCD to access the 2 Screws (419, 457)
as shown below, then remove it.
as shown below, then remove it.
Installation of Side Case R Unit
When installing, pay attention to the direction of the Shaft
Case Unit. So, be sure to install the LCD (Ass'y) into the
Side Case R Unit with the LCD rotate as shown. Otherwise,
the LCD open/close switch on the Side Case R Unit will be
damaged.
When installing, pay attention to the direction of the Shaft
Case Unit. So, be sure to install the LCD (Ass'y) into the
Side Case R Unit with the LCD rotate as shown. Otherwise,
the LCD open/close switch on the Side Case R Unit will be
damaged.
Fig. D11
LCD (Ass'y)
Side Case R Unit
Rotate
Rotate
LCD open/close SW.
419
457
Shaft Case Unit
9. Removal of Jack C.B.A. & Bottom Angle Ass'y
1) Open the L Cover.
2) Remove the Screw (450) and release the Tripod Portion
2) Remove the Screw (450) and release the Tripod Portion
from the hole.
Installation of Jack C.B.A. & Bottom Angle Ass'y
Insert the both of Jack C.B.A. & Bottom Angle Ass'y into the
2 slots and secure the Tripod to the hole.
Insert the both of Jack C.B.A. & Bottom Angle Ass'y into the
2 slots and secure the Tripod to the hole.
Fig. D9
10. Installation of Front C.B.A.
1) Install the Four Eye Lens (For model with Light) into
the Front Case. Then, install the Front C.B.A. with 2
bosses of the Four Eye Lens and 2 Screws (533).
bosses of the Four Eye Lens and 2 Screws (533).
2) Install the Light Shield Sheet with 2 Screws (533).
Fig. D10
Jack C.B.A. &
Bottom Angle Ass'y
Bottom Angle Ass'y
Tripod
slot
slot
Open L Cover
hole
450
Front
C.B.A.
C.B.A.
Light Shield Sheet
boss (For model with Light)
boss (For model with Light)
Four Eyes Lens
(For model with Light)
(For model with Light)
Front Case
533
533
533
533
47
NV-GS6EE NV-GS6GC
12. Installation of LCD C.B.A., LCD Panel Ass'y, LCD Shield
Case Unit, LCD Case B
Use extreme care the LEDs when handling the LCD C.B.A.
Install in order shown below.
1) Install the LCD Panel Ass'y onto the LCD Shield Case
Use extreme care the LEDs when handling the LCD C.B.A.
Install in order shown below.
1) Install the LCD Panel Ass'y onto the LCD Shield Case
Unit with the 3 Locking Tabs (L-4) while bending at the
base of the LCD F.P.C. so as not to damage it.
base of the LCD F.P.C. so as not to damage it.
2) Install them into the LCD Case B with the 4 Locking
Tabs (L-3).
3) Install the LCD C.B.A. onto the LCD Panel Ass'y with
the Locking Tab (L-2).
4) Tighten the Screw (542) while keeping the LCD C.B.A.
pressed toward the right. Then, connect the Connector
FP8102.
FP8102.
Fig. D12
boss
LCD
Shield
Case
Unit
Shield
Case
Unit
LCD Panel Ass'y
LCD
F.P.C.
F.P.C.
LCD C.B.A.
LCD Case B
(L-3)
(L-3)
(L-3)
(L-4)
(L-4)
(L-3)
(L-2)
FP8102
Press
Bend
542
48
NV-GS6EE NV-GS6GC
Click on the first or last page to see other NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G service manuals if exist.