Panasonic NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G Service Manual ▷ View online
7.1.3. SERVICE MENU
This function displays the following items in the Service Menu.
To enter the Service Menu:
Press the MENU button on the operation panel. Then, press and hold the QUICKSTART, the Joystick Control LEFT and the
PHOTOSHOT keys for more than 3 seconds without the SD Card. The Service Menu will be displayed.
PHOTOSHOT keys for more than 3 seconds without the SD Card. The Service Menu will be displayed.
Note:
1. When an Error is displayed "PUSH THE RESET SWITCH" is displayed on the monitor, it is not necessary to push the
MENU button to enter the Service Menu.
2. Do not operate items 1, 2, 4, 5, 6 in the Service Menu.
Fig. 3
*a...Software version
*b...Cylinder elapsed time (in Base 16), Mechanism lock code record and Lens Motor lock code record
*c...Self test
*d...Cylinder elapsed time reset
After replacing the Cylinder Unit, clear the Cylinder elapsed time to 0.Press the Joystick Control keys to select this item. Then,
press the Joystick Control CENTER key .
press the Joystick Control CENTER key .
To exit the Service Menu:
Unplug the DC Cord.
Note:
After repairing, to delete all lock code, press and hold the QUICKSTART, the Joystick Control LEFT and the REC/PAUSE
buttons for more than 3 seconds in power on condition (without the SD Card). Otherwise, new lock code will not be recorded
correctly.
buttons for more than 3 seconds in power on condition (without the SD Card). Otherwise, new lock code will not be recorded
correctly.
When all lock code reset END OSD will appear on the top right corner of the LCD panel then unplug the DC Cord.
25
NV-GS6EE NV-GS6GC
7.1.4. REMOVAL/INSTALLATION OF
F.P.C. FROM NON ZIF (Zero
Insertion Force) CONNECTOR
Insertion Force) CONNECTOR
Removal/Installation of F.P.C. from the Non ZIF (Zero
Insertion Force) connector:
Insertion Force) connector:
1. The Non ZIF connectors and the ZIF connectors are used
on the unit. And there are 2 types (Type A, Type B) of Non
ZIF connectors.
ZIF connectors.
2. To remove the F.P.C. from the Non ZIF connector, use the
Plier for Non ZIF Connector (LSVQ0028) to pull out the
F.P.C. as shown. The same Plier for Non ZIF Connector
(LSVQ0028) should also be used to install the F.P.C. to the
Non ZIF Connector.
F.P.C. as shown. The same Plier for Non ZIF Connector
(LSVQ0028) should also be used to install the F.P.C. to the
Non ZIF Connector.
Fig. 4-1
3. Connect the F.P.C.s to the Non ZIF connectors, verifying
the direction of F.P.C as shown.
Fig. 4-2
7.1.5. METHOD FOR
LOADING/UNLOADING OF
MECHANISM
MECHANISM
CAUTION:
If loading does not start after DC Power Supply is applied,
DO NOT continue to apply DC Power.
DO NOT continue to apply DC Power.
Apply +3 VDC Power Supply to the Loading Motor terminals.
Loading:
DC (-) to Portion "a," DC (+) to Portion "b"
Unloading:
DC (+) to Portion "a," DC (-) to Portion "b"
Fig. 5
26
NV-GS6EE NV-GS6GC
7.1.6. EEPROM DATA
CAUTION:
Be sure to save the EEPROM data using PC-EVR
Adjustment Program before service and adjustment in
order to make sure to avoid an accidental data loss, etc.
using PC-EVR Adjustment Program by first.
Adjustment Program before service and adjustment in
order to make sure to avoid an accidental data loss, etc.
using PC-EVR Adjustment Program by first.
27
NV-GS6EE NV-GS6GC
7.1.7. SIGNAL DESCRIPTION ON MEASURING BOARD FOR ELECTRICAL ADJUSTMENT
(VFK1308E)
A signal check can be performed using the Measuring Board.
Fig. 6-1
28
NV-GS6EE NV-GS6GC
Click on the first or last page to see other NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G service manuals if exist.