Panasonic NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G Service Manual ▷ View online
13. Installation of LCD Panel, Reflect Sheet, Lead Light
Panel, Diffusion Sheet, BEF Sheet, BEF Sheet A, Panel
Holder Unit
a. When replacing the LCD Panel, the Diffusion Sheet,
Holder Unit
a. When replacing the LCD Panel, the Diffusion Sheet,
the BEF Sheet and the BEF Sheet A, make sure to
remove the Protection Sheets.
remove the Protection Sheets.
To distinguish the sheets with Protection Sheet
attached:
- A blue Protection Sheet is affixed to both faces of the
Diffusion Sheet.
- A yellow Protection Sheet is affixed to both faces of
the BEF Sheet.
- A transparent Protection Sheet is affixed to both
faces of the BEF Sheet A.
b. Use extreme care when handling the LCD Panel, the
Reflect Sheet, the Lead Light Panel, the Diffusion
Sheet, the BEF Sheet and the BEF Sheet A to avoid
damage, dust, and spots (especially fingerprints, etc.)
Sheet, the BEF Sheet and the BEF Sheet A to avoid
damage, dust, and spots (especially fingerprints, etc.)
Install in order shown below.
1) Install the BEF Sheet A, BEF Sheet and Diffusion Sheet
1) Install the BEF Sheet A, BEF Sheet and Diffusion Sheet
while inserting the corners of the sheets to the slots of
the Panel Holder Unit in order.
the Panel Holder Unit in order.
2) Install the Lead Light Panel while inserting the corners
to the slots of the Panel Holder Unit.
3) Align the Reflect Sheet with the edge of the Panel
Holder Unit, and install it using adhesive tape on the
Reflect Sheet.
Reflect Sheet.
Fig. D13-1
4) Install the LCD Panel with adhesive tape so that the
cross marks are positioned in the center of the holes of
the Panel Holder Unit.
the Panel Holder Unit.
BEF Sheet A
BEF Sheet
(yellow)
(blue)
(green)
Diffusion Sheet
Protection Sheet
Protection Sheet
Protection Sheet
Reflect Sheet
Do not touch
the surface of
Lead Light Panel.
the surface of
Lead Light Panel.
Panel Holder Unit
adhesive
tape
tape
Fig. D13-2
(stripe)
BEF Sheet A
Panel Holder Unit
(L-5)
LCD Panel
Lead Light Panel
Reflect Sheet
adhesive
tape
tape
adhesive
tape
tape
adhesive
tape
tape
View A
View A
cross mark
cross mark
hole of Panel
Holder Unit
Holder Unit
hole of Panel
Holder Unit
Holder Unit
cross mark
cross mark
slot
hole
hole
slot
BEF Sheet
Diffusion Sheet
(white)
(gray)
49
NV-GS6EE NV-GS6GC
14. Removal of CCD C.B.A., Filter Rubber, Optical Filter,
Filter Holder
CAUTION:
1) When removing the CCD C.B.A., take care that the
CAUTION:
1) When removing the CCD C.B.A., take care that the
Optical Filter does not fall out.
2) Take extreme caution when removing the CCD C.B.A.
as it is easily damaged by static electricity. Use a Wrist
Strap while removing and installing.
Strap while removing and installing.
3) Do not touch the CCD window surface.
Installation of CCD C.B.A., Filter Rubber, Optical Filter,
Filter Holder
Install in order shown below.
1) Install the Filter Holder (For model with 30X zoom)
Installation of CCD C.B.A., Filter Rubber, Optical Filter,
Filter Holder
Install in order shown below.
1) Install the Filter Holder (For model with 30X zoom)
correctly.
2) Install the Optical Filter correctly.
Note: Make sure that no dust gets on the Optical Filter
or in the Lens Unit. Clean the Optical Filter with lens
cleaning paper dampened with lens cleaner if
necessary.
cleaning paper dampened with lens cleaner if
necessary.
3) Install the Filter Rubber on the Optical Filter correctly as
shown below.
Note: Make sure that no dust gets on the Filter
Rubber.
4) Install the CCD C.B.A. into the Lens Unit. Then, tighten
the 2 Screws (536).
Note: Do not touch the Lens Surface. Clean the surface
with lens cleaning paper dampened with lens cleaner
if necessary.
if necessary.
15. Installation of Zoom Motor Unit/Focus Motor Unit
Install the Zoom Motor Unit/Focus Motor Unit so that the
Shaft of the Zoom Motor Unit/Focus Motor Unit is set in the
Holder.
Shaft of the Zoom Motor Unit/Focus Motor Unit is set in the
Holder.
Fig. D15
16. Installation of EVF Slide Piece, EVF Base Frame
1) Pass the EVF F.P.C. through the EVF Base Frame
hole.
2) Install the EVF Slide Pieces into the EVF Base Frame
from the both side.
3) Slide the EVF Case Ass'y to the end so that the ribs are
inserted to the holes of the EVF Slide Pieces.
4) Confirm the threaded holes, and tighten the 2 Screws
(450).
5) After installing, confirm the EVF moves correctly.
Fig. D16
Focus
Motor
Unit
Motor
Unit
Zoom
Motor
Unit
Motor
Unit
shaft
shaft
holder
holder
Bosses
Bosses
hole of EVF
Slide Piece
Slide Piece
hole of EVF
Slide Piece
Slide Piece
rib
hole
EVF F.P.C.
EVF Case Ass'y
EVF Base Frame
rib
<Top View>
<Side View>
EVF Slide Piece
EVF Base Frame
(threaded hole)
Slide
450
50
NV-GS6EE NV-GS6GC
17. Installation of EVF Spring, EVF F.P.C.
1) Insert the EVF F.P.C. into the EVF Spring hole paying
particular attention to the direction.
2) Connect the EVF F.P.C. to Connector FP951.
3) Insert the Locking Tab (L-2) at first, then fit the EVF
3) Insert the Locking Tab (L-2) at first, then fit the EVF
Spring in the EVF Case and tighten the Screw (450).
Fig. D17
18. Removal of Eye Cap
Remove the Eye Cap after removing the 2 Screws (524).
19. Handling cautions of EVF Lens Unit
Use extreme care when handling the EVF Lens Unit to
avoid damage, dust, and spots (especially fingerprints,
etc.)
avoid damage, dust, and spots (especially fingerprints,
etc.)
Installation of EVF Lens Unit, Eye Sight Lever
1) Install the Eye Sight Lever into the EVF Case hole at the
1) Install the Eye Sight Lever into the EVF Case hole at the
direction as shown.
2) Install the EVF Lens Unit into the EVF Case while
grasping both sides of the springs with tweezers or, etc.
3) After installing, confirm the Eye Sight Lever and the
EVF Lens Unit work together correctly.
Fig. D19
EVF Spring
EVF Case
Fit
(L-2)
hole
FP951
EVF F.P.C.
EVF Lens Unit
Eye Sight Lever
hole
EVF Case
Spring
Spring
Bosses
Bosses
Tweezers
51
NV-GS6EE NV-GS6GC
8.2. MECHANISM SECTION
Flow-Chart for Disassembly Procedures
Fig. M1
Fig. M2
52
NV-GS6EE NV-GS6GC
Click on the first or last page to see other NV-GS6EE / NV-GS6GC / NV-GS17E / NV-GS17EB / NV-GS17EG / NV-GS17EP / NV-GS18E / NV-GS21E / NV-GS21EB / NV-GS21EG / NV-GS21EK / NV-GS21EP / NV-GS25GC / NV-GS25GCD / NV-GS25GN / NV-GS28GK / NV-GS35E / NV-GS35EB / NV-GS35EG / NV-GS35EP / NV-GS35GC / NV-GS35G service manuals if exist.