Panasonic KX-FLB853RU / KX-FA101A / KX-FA102A / KX-FA104E Service Manual ▷ View online
3.
Lift the cover release lever (1) and open the top cover (2).
Important:
·
Close the multi-purpose input tray (3) before opening the
top cover.
top cover.
4.
Tap on the used toner cartridge several times to allow the remaining
toner to fall into the drum unit. Remove the drum and toner unit (1)
by holding the two tabs.
toner to fall into the drum unit. Remove the drum and toner unit (1)
by holding the two tabs.
·
If you replace the toner cartridge and the drum unit at the same
time, skip to step 7.
time, skip to step 7.
5.
Turn the two green levers (1) on the used toner cartridge firmly.
33
KX-FLB853RU
6.
Remove the used cartridge (1) from the drum unit (2).
·
The toner may stick to the cartridge and the drum unit. Be
careful when handling.
careful when handling.
·
Do not drop the toner on the black drum surface (3).
·
Put the used toner cartridge into the protection bag.
7
7.
If you replace the drum unit at the same time, remove the new drum
unit from the protection bag.
Place the new toner cartridge (1) into the drum unit (2).
unit from the protection bag.
Place the new toner cartridge (1) into the drum unit (2).
8.
Firmly press down the toner cartridge to snap into position.
9.
Turn the two green levers (1) on the toner cartridge firmly.
10.
Make sure that the triangles (1) match to install the toner cartridge
correctly.
correctly.
34
KX-FLB853RU
·
If the lower glass (2) is dirty, clean it with a soft and dry cloth.
11.
Install the drum and toner unit (1) by holding the tabs.
·
Make sure that the triangles (2) match to install the drum and toner
unit correctly.
unit correctly.
12.
Close the top cover, holding the cover release lever (1). Then push
down the right centre edge, until locked.
down the right centre edge, until locked.
Caution:
·
To prevent injuries, be careful not to put your hands
under the top cover.
under the top cover.
Note:
·
While the unit displays “PLEASE WAIT”, do not open the top cover, or turn the power switch OFF.
Waste disposal method
Waste material should be disposed of under conditions which meet all national and local environmental regulations.
35
KX-FLB853RU
·
The screenshots shown in these instructions are for
Windows XP and are included for reference only.
Windows XP and are included for reference only.
·
The screenshots shown in these instructions may differ
slightly from those of the actual product.
slightly from those of the actual product.
·
Software features and appearance are subject to
change without notice.
change without notice.
1. Start Windows and exit all other applications.
·
For Windows XP and Windows 2000 users, you must be
logged in as an administrator in order to install Multi-
Function Station.
logged in as an administrator in order to install Multi-
Function Station.
·
Install Multi-Function Station before connecting the unit
to a computer. If the unit is connected to a computer
before installing Multi-Function Station, the [Found
New Hardware Wizard] dialogue box will appear. Click
[Cancel] to close it.
to a computer. If the unit is connected to a computer
before installing Multi-Function Station, the [Found
New Hardware Wizard] dialogue box will appear. Click
[Cancel] to close it.
2. Insert the included CD-ROM into your CD-ROM drive.
·
The [Choose Setup Language] dialog box will appear.
Select the desired language that you want to use with this
software
Select the desired language that you want to use with this
software
from
the
drop-down
list.
Click
[OK].
The
installation will automatically start.
·
If the [Choose Setup Language] dialog box does not
appear:
appear:
The installation will automatically start.
·
If the installation does not start automatically:
Click [Start]. Choose [Run...]. Type “D:\setup” (where “D:”
is the drive letter of your CD-ROM drive). Click [OK].
is the drive letter of your CD-ROM drive). Click [OK].
(If you are not sure what the drive letter is for your CD-ROM
drive, use Windows Explorer and look for the CD-ROM
drive.)
drive, use Windows Explorer and look for the CD-ROM
drive.)
The installation will start.
3. When the setup program starts, follow the on-screen
instructions.
instructions.
4. When the [Setup Type] dialogue box appears, select
[Standard], then click [Next].
[Standard], then click [Next].
·
Readiris OCR software and Device Monitor will also be
installed.
installed.
5. When the [Connect Type] dialogue box appears, select
[Connect directly with a USB cable.], then click [Next].
[Connect directly with a USB cable.], then click [Next].
·
The [Connect Device] dialog box will appear.
6. Connect the unit with the USB cable, then click [Next].
·
If the unit is connected to your computer, the model name
will be automatically detected.
will be automatically detected.
·
You can change the names for the printer, PC fax, and
scanner if necessary.
scanner if necessary.
7. Click [Install], then follow the on-screen instructions.
·
The files will be copied to your computer.
Important notice for Windows XP users
·
If you use Windows XP, the following message may
appear:
appear:
“The software you are installing for this hardware has not
passed Windows Logo testing to verify its compatibility with
Windows XP”
passed Windows Logo testing to verify its compatibility with
Windows XP”
This is normal and the software will not cause any
difficulties with your operating system. You can continue the
installation with no problem.
difficulties with your operating system. You can continue the
installation with no problem.
Note:
·
If the screen prompts to insert the CD-ROM for operating
system when installing Multi-Function Station, insert it into
your CD-ROM drive.
system when installing Multi-Function Station, insert it into
your CD-ROM drive.
3.3.11. INSTALLING MULTI-FUNCTION STATION
36
KX-FLB853RU
Click on the first or last page to see other KX-FLB853RU / KX-FA101A / KX-FA102A / KX-FA104E service manuals if exist.