Panasonic SA-XH10EE / SC-XH10EE Service Manual ▷ View online
37
8.2.
DVD/CD Laser Diode current measurement.
This section will illustrate procedures of measuring& deriving DVD/CD Laser Diode Current.
DVD Laser Diode Current Measurement
CD Laser Diode Current Measurement
Checking Item/ Formula
Remarks
Item Description
1. Measurement the voltage (V
CD
) on the testpoints CL8530(+) & CL8531(-).
This is voltage across R8566 which has a resistance value of 4.7 ohm.
2. Calculate the CD Laser current by the following formula:
CD_LD=VCD/4.7
1. Measurement the voltage (V
DVD
) on the testpoints CL8530(+) & CL8532(-).
This is voltage across R8556 which has a resistance value of 4.7 ohm.
2. Calculate the DVD Laser current by the following formula:
DVD_LD=VCD/4.7
Refer to 8.2.1.
Backend P.C.B.
(Fig. 3. Backend
P.C.B.)
Backend P.C.B.
(Fig. 3. Backend
P.C.B.)
Refer to 8.2.1.
Backend P.C.B.
(Fig. 3. Backend
P.C.B.)
Backend P.C.B.
(Fig. 3. Backend
P.C.B.)
3. Specification for CD laser current is
58 mA
3. Specification for DVD laser current is
58 mA
38
8.2.1.
Backend P.C.B
Fig. 3. Backend P.C.B.
CL8530, CL8531, CL8532
R8556
R8566
(Side A of Backend P.C.B.)
(Side B of Backend P.C.B.)
39
8.3.
Basic Troubleshooting Guide for Traverse Unit (Backend P.C.B.)
Problems Checking
Points
Checking
components
b) Check video signals (CVBS)
LB8317, R8325 (CVBS)
a) Check SDRAM address, data
bus, CLK and other control signals
waveform
bus, CLK and other control signals
waveform
IC8051
1) Distorted picture or
abnormal sound is head
during the initialization
abnormal sound is head
during the initialization
c) Check audio DAC circuitry
* Compare the above with
OK condition DVD Module
P.C.B
OK condition DVD Module
P.C.B
LB8422 till LB8428
*Check for solder short and/or
component missing/damaged
component missing/damaged
b) Check laser drive circuitry
(Voltages & current)
(Voltages & current)
Q8552, CL8510
Q8562, CL8520
Q8562, CL8520
(For DVD),
(For CD)
(For CD)
a) Check motor driver circuitry
(VCC PVCC)
(VCC PVCC)
IC8251 Pin 8, (+9V), 21 (+5V)
2) No TOC/Long TOC
c) Check LSI IC connection to
motor drive circuitry
* Compare the above with OK
condition Main P.C.B.
* Compare the above with OK
condition Main P.C.B.
IC8001 Pin 90, 93, 94, 95
IC8251 Pin 11 to 18
* Check for solder short and/or
component missing/damaged
IC8251 Pin 11 to 18
* Check for solder short and/or
component missing/damaged
a) Check connection from
Main to Traverse unit
Main to Traverse unit
FP8251
3) Disc not spinning
4) Traverse not moving
5) Traverse and spindle
abnormal movement
4) Traverse not moving
5) Traverse and spindle
abnormal movement
b) Check motor driver circuitry on
the voltages and control signals
* Compare the above with
OK condition Main P.C.B.
the voltages and control signals
* Compare the above with
OK condition Main P.C.B.
IC8251
* Check for solder short and/or
component damaged
component damaged
6) Cannot read the disc but
spindle motor is spinning
spindle motor is spinning
- Cannot read CD/DVD
a) Check laser drive circuitry
(voltages and current)
(voltages and current)
- Check CD Laser Drive
- Check DVD Laser Drive
* Check voltages and LD current
and compare with OK condition
Main P.C.B.
Q8552, LB8551
(For DVD Laser Drive current)
Q8562, LB8561
(For CD Laser Drive current)
(For DVD Laser Drive current)
Q8562, LB8561
(For CD Laser Drive current)
7) Block Noise during play
a) Check SDRAM address and
data bus signal
IC8051
8) Jitter out of specification
a) Check LD current
b) Check OPU (Change to other
unit and confirmed operating
condition)
unit and confirmed operating
condition)
OPU Unit (Traverse unit), FPC
connection (FP8531 & FP8251)
connection (FP8531 & FP8251)
40
8.4.
Basic Troubleshooting Guide for HDMI AV output
Problems Checking
Points
Checking
components
1) Check setting of the set in
Setup Menu whether the HDMI
Video output is turned ON
Setup Menu whether the HDMI
Video output is turned ON
* This year HDMI always ON.
No need check Setup Menu.
If no resolution selection GUI, then
only check SETUP.
2) +5V Supply to the TV
IC3952 (Pin 4)
3) HDMI Connector Solderability
condition
condition
P3901
4) HDMI Output TDMS signal
HDMI Connector (P3901)
lines (IC3901)
- Clock (TXCP/TXCM =>
Pin 50, 49)
- Data (TX0P/M => Pin 52, 51)
Pin 50, 49)
- Data (TX0P/M => Pin 52, 51)
- Data (TX1P/M => Pin 54, 53)
- Data (TX2P/M => Pin 56, 55)
- Data (TX2P/M => Pin 56, 55)
- Clock (TXCP/TXCM =>
Pin 10, 12)
- Data (TX0P/M => Pin 7, 9)
Pin 10, 12)
- Data (TX0P/M => Pin 7, 9)
- Data (TX1P/M => Pin 4, 6)
- Data (TX2P/M => Pin 1, 3)
- Data (TX2P/M => Pin 1, 3)
HDMI Connector (P3901)
- Clock (TXCP/TXCM =>
Pin 10, 12)
- Data (TX0P/M => Pin 7, 9)
Pin 10, 12)
- Data (TX0P/M => Pin 7, 9)
- Data (TX1P/M => Pin 4, 6)
- Data (TX2P/M => Pin 1, 3)
- Data (TX2P/M => Pin 1, 3)
- Data, SDA (Pin 46, IC8001)
- Clock, SCL (Pin 47, IC8001)
5) HDMI Transmitter
communication lines to TV
communication lines to TV
6) HDMI Transmitter
communication from LSI (IC8001)
+3.3V Supply
communication from LSI (IC8001)
+3.3V Supply
7)HDMI Transmitter LSI IC (IC8001)
+1.8 V Supply
+1.8 V Supply
8) Hot-Plug Signal
9) HDMI Interface Reference
Resistor
Resistor
1) Supply fo HDMI transmitter
intergrated (IC8001)
intergrated (IC8001)
2) Check for Capacitor short to GND
Check Digital Signal Data
communication lines from IC8001 to
Serial Flash IC (IC8651)
communication lines from IC8001 to
Serial Flash IC (IC8651)
Check the setting under ’SETUP’
menu if HDMI Audio Output option
is turned ’ON’
menu if HDMI Audio Output option
is turned ’ON’
* Check for solder short/or
component missing on TDMS line
as well as signal intergrity
component missing on TDMS line
as well as signal intergrity
LB3905, R3905, Q3902, R3904
LB3904, R3907, Q3903, R3906
LB3901 (Pin 57)
LB3902, LB3910, R3910 (Pin 59)
LB3906, R3902, R3903, Q3901
C8034, C8006C C8029, C8028,
Pin 1, 2, 5, 6 (IC8651)
Pin 105, 106, 107, 109 (IC8001)
LB3901 (Pin 57), LB3902, LB3910
(Pin 59)
(Pin 59)
R3901
1) TV does not have any
display. Set FL display
shows U702/U703
display. Set FL display
shows U702/U703
2) When switching the video
output mode from 480p to
720p /1080i, TV display
become blank
output mode from 480p to
720p /1080i, TV display
become blank
3) Error Video Output. TV
screen shows green Display
screen shows green Display
4) No audio output from HDMI
Click on the first or last page to see other SA-XH10EE / SC-XH10EE service manuals if exist.