Panasonic SA-XH10EE / SC-XH10EE Service Manual ▷ View online
33
7.6.2.
Process Flow (2/2)
To initialize, press and hold
main unit [STOP] then
press remote control key
[>10].
main unit [STOP] then
press remote control key
[>10].
Update Completed
If firmware software update
completes successfully:
completes successfully:
GUI Display 1.3:
Firmware update is completed,
please open the tray and remove
the disc
GUI Display 1.3:
Step 5
Eject the disc and power off main
unit.
Eject the disc and power off main
unit.
Step 6
Power on the unit and do system
initialize.
Power on the unit and do system
initialize.
Step 7 Update process finish.
FL/ GUI Display
Remarks
Item
Description
Process
FL Display 1.6:
FL Display (Main Unit) will
display "GOOD" as
"FL Display 1.6" shown.
display "GOOD" as
"FL Display 1.6" shown.
34
8 Troubleshooting Guide
8.1.
Troubleshooting Guide for F61 and/or F76
This section illustrates the checking procedures when upon detecting the error of “F61” and/or “F76” after power up of the unit. It is
for purpose of troubleshooting and checking in SMPS P.C.B..
for purpose of troubleshooting and checking in SMPS P.C.B..
Symptom(s)
Checking items
Possible Fault(s)
Remarks
Set cannot Power ON:
Condition 1: With
Stanby LED on
Stanby LED on
1
2
1
Solder crack,dry joint ,short
circuit,open circuit,etc
circuit,open circuit,etc
AC cord
AC Inlet P5701
1 Faulty AC cord, loose
connection
2
2
Solder crack,dry joint ,short
circuit,open circuit,etc
circuit,open circuit,etc
4
Check FFC connection/
alignment from SMPS (H2016)
to Main (CN100)
alignment from SMPS (H2016)
to Main (CN100)
2
P5701 solder crack, dry joint
etc
etc
Faulty IC2900
Set can Power ON
then F61
then F61
Set can Power ON
then F76
then F76
Set can Power ON
working normally for
sometime then F61
working normally for
sometime then F61
Condition 2: With
Stanby LED Off or
flickering
Stanby LED Off or
flickering
3
1
2
3
3 F1 Fuse open
Fuse F1
DC-DC circuit
1 Thermal Diode D5706
SMPS FFC loose
Voltage regulator
4 Photocoupler PC701
1 Transformer T5701
2 Photocoupler PC701
1a Pin 14/15 shorted to pin 12/13
1a
1b
L421 Open (no input to
IC106)
Faulty IC106 (no output
voltage at pin 3)
IC106)
Faulty IC106 (no output
voltage at pin 3)
1a
1b
Improper contact between
D5706 to heatsink
OTP (thermal) protection
trigger prematurely
D5706 to heatsink
OTP (thermal) protection
trigger prematurely
3a Faulty Q107 Transistor diode
check (cannot switch ON then
NO +9V)
NO +9V)
3b K304 Open (+3V line going
to Panel PCB CN203)
1c Faulty Q100 (regulator)
1d L125 open (No DC +5V)
1e R100 open (No DC +9V)
1) Refer to Fig. 1. SMPS P.C.B.
Refer to Fig. 1. SMPS P.C.B.
Refer to Fig. 1. SMPS P.C.B.
Refer to Fig. 1. SMPS P.C.B.
Refer to Schematic Diagram of
SMPS Circuit (Item 17.5) for
terminal pin count on primary and
secondary terminals
SMPS Circuit (Item 17.5) for
terminal pin count on primary and
secondary terminals
SMPS Circuit (Item 17.5)
2) Refer to Schematic Diagram of
1) Refer to Fig. 2. Main P.C.B.
Main Circuit (Item 17.3)
2) Refer to Schematic diagram of
1) Refer to Fig. 2. Main P.C.B.
Main Circuit (Item 17.3)
2) Refer to Schematic diagram of
1 Regulator IC IC2900
35
8.1.1.
SMPS P.C.B.
Fig. 1. SMPS P.C.B.
AC Inlet Jack : P5701
Fuse : F1
Regulator IC :
IC2900
IC2900
Thermal Diaod :
D5706
D5706
Photocoupler :
PC701
PC701
H2016
FFC Conector : H2016
Transformer : T5701
36
8.1.2.
Main P.C.B.
Fig. 2. Main P.C.B.
Conector:CN100
Transistor:Q107
Resistor:R100
Inductors : L421
Chip Jumper:K304
DC/DC
CONVERTER
IC: IC106
CONVERTER
IC: IC106
Inductors : L125
Click on the first or last page to see other SA-XH10EE / SC-XH10EE service manuals if exist.