JBL SOUNDFLY BT (serv.man3) EMC - CB Certificate ▷ View online
Page 8 of 38
Report No. : 12-1330-0056
IEC/EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
c) Markings on supply output terminals
No such terminals.
N/A
5.3
a) Use of triangle with exclamation mark
The marks are shown on the
technical documents near
every safety critical
component.
technical documents near
every safety critical
component.
P
b) marking on loudspeaker grille, IEC 60417-5036
N/A
5.4
Instructions for use
User
’s manual was provided in
English.
P
5.4.1
a) Mains powered equipment not exposed to
dripping or splashing. Warning concerning objects
filled with liquid, etc.
dripping or splashing. Warning concerning objects
filled with liquid, etc.
The statement in operating
manual complies with the
requirement.
manual complies with the
requirement.
P
b) Hazardous live terminals, instructions for wiring
No hazardous live t erminals.
N/A
c) Instructions for replacing lithium battery
A w arning in inst ruct ion
manual.
manual.
P
d) Class I earth connection warning
P
e) Instructions for multimedia system connection
N/A
f) Special stability warning for attachment of the
apparatus to the floor/wall
apparatus to the floor/wall
N/A
g) Warning: battery exposure to heat
N/A
h) Warning: protective film on CRT face
N/A
5.4.2
a-b) Disconnect device: plug/coupler or all-pole
mains switch location, accessibility and markings
mains switch location, accessibility and markings
The mains plug is used as
disconnect device, t he
st at ement w as provided in
t he user
disconnect device, t he
st at ement w as provided in
t he user
’ s manual.
P
c) Instructions for permanently connected equipment
N/A
Marking, signal lamps or similar for completely
disconnection from the mains
disconnection from the mains
N/A
6
Hazardous radiation
N/A
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
N/A
Ionizing radiation under fault condition
N/A
6.2
Laser radiation, emission limits to IEC 60825-1:2007
................................................................................... :
................................................................................... :
N/A
Emission limits under fault conditions ..................... :
N/A
7
Heating under normal operating conditions
P
7.1
Temperature rises not exceeding specified values;
fuse links and other protective devices defeated
fuse links and other protective devices defeated
(see appended table 7.1)
P
7.1.1
Temperature rise of accessible parts
(see appended table 7.1)
P
Page 9 of 38
Report No. : 12-1330-0056
IEC/EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
7.1.2
Temperature rise of parts providing electrical
insulation
insulation
(see appended table 7.1)
P
7.1.3
Temperature rise of parts acting as a support or as a
mechanical barrier
mechanical barrier
(see appended table 7.1)
P
7.1.4
Temperature rise of windings
(see appended table 7.1)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
(see appended table 7.1)
P
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
o
C
The input current is small than
0.2A.
0.2A.
P
8
Constructional requirements with regard to the protection against electric
shock
shock
P
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
untreated textile oxide films and beads etc.
considered to be bare
Considered.
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
device, fuse-links or handling drawers etc.
N/A
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
hygroscopic material
The apparatus was subjected
of humidity treatment for 168
hrs at 40
of humidity treatment for 168
hrs at 40
o
C and R.H. of 95%.
After the tests, the tests of 10.3
are made and pass.
are made and pass.
P
8.4
No risk of electric shock from accessible parts or
from parts rendered accessible following the
removal of a cover which can be removed by hand
from parts rendered accessible following the
removal of a cover which can be removed by hand
N/A
8.5
Class I equipment
See below.
P
Basic insulation between hazardous live parts and
earthed accessible parts
earthed accessible parts
Hazardous live parts to
earthed parts are separated by
basic insulation.
earthed parts are separated by
basic insulation.
P
Resistors bridging basic insulation complying with
14.1 a)
14.1 a)
N/A
Capacitors bridging basic insulation complying with
14.2.1 a)
14.2.1 a)
N/A
Protective earthing terminal
P
8.6
Class II equipment and Class II constructions within
Class I equipment
Class I equipment
See below.
P
Double or reinforced insulation between hazardous
live parts and accessible parts
live parts and accessible parts
Hazardous live parts to
accessible parts are separated
by either reinforced or double
insulation.
accessible parts are separated
by either reinforced or double
insulation.
P
Page 10 of 38
Report No. : 12-1330-0056
IEC/EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
Components bridging double or reinforced insulation
complying with 14.1 a) or 14.3
complying with 14.1 a) or 14.3
The isolating transformer has
been tested within this report
and complying with subclause
14.3.
been tested within this report
and complying with subclause
14.3.
P
Basic insulation bridged by components complying
with 14.3.4.3.
with 14.3.4.3.
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.1 a)
bridged by a capacitor complying with 14.1 a)
N/A
Double or reinforced insulation being bridged with 2
capacitors in series complying with 14.2.1 a)
capacitors in series complying with 14.2.1 a)
N/A
Double or reinforced insulation being bridged with a
single capacitor complying with 14.2.1 b)
single capacitor complying with 14.2.1 b)
Hazardous live parts and
accessible parts separated by
one capacitor, which used was
certified as Y1 capacitor
according to IEC 60384-14.
accessible parts separated by
one capacitor, which used was
certified as Y1 capacitor
according to IEC 60384-14.
P
8.7
This clause is void
N/A
8.8
Basic or supplementary insulation > 0,4 mm (mm) :
N/A
Reinforced insulation > 0,4 mm (mm) .................... :
The photo coupler and internal
plastic enclosure which were
provided distance through
insulation of minimum 0.4 mm.
See appended table 14 for
details.
plastic enclosure which were
provided distance through
insulation of minimum 0.4 mm.
See appended table 14 for
details.
P
Thin sheet insulation (excluding non-separable thin
sheet insulation. See 8.22)
sheet insulation. See 8.22)
The thin sheet materials of
polyester tape used in
transformers.
polyester tape used in
transformers.
P
Basic or supplementary insulation, at least two
layers, each meeting 10.3
layers, each meeting 10.3
N/A
Basic or supplementary insulation, three layers any
two of which meet 10.3
two of which meet 10.3
N/A
Reinforced insulation, two layers each of which meet
10.3
10.3
(see appended table 13)
P
Reinforced insulation, three layers any two which
meet 10.3
meet 10.3
N/A
8.9
Adequate insulation between internal hazardous live
conductors and accessible parts
conductors and accessible parts
All internal wires with only
basic isolation are routed so
that they are not close to any
live bare components.
basic isolation are routed so
that they are not close to any
live bare components.
P
Adequate insulation between internal hazardous live
parts and conductors connected to accessible parts
parts and conductors connected to accessible parts
All internal hazardous live parts
are separated by double or
reinforced insulation form
conductors connected to
accessible parts.
are separated by double or
reinforced insulation form
conductors connected to
accessible parts.
P
Page 11 of 38
Report No. : 12-1330-0056
IEC/EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
8.10
Double insulation between conductors connected to
the mains and accessible parts.
the mains and accessible parts.
Class I equipment.
N/A
Double insulation between internal hazardous live
parts and conductors connected to accessible parts.
parts and conductors connected to accessible parts.
N/A
8.11
Detaching of wires
Conductors with mechanical
securing.
No wire could be became
detached after the test below.
securing.
No wire could be became
detached after the test below.
P
No undue reduction of creepages or clearance
distances if wires become detached
distances if wires become detached
No undue reduction of
creepage and clearance
distances below the values
specified in clause 13.
creepage and clearance
distances below the values
specified in clause 13.
P
Vibration test carried out ......................................... :
See subclause 12.1.2.
P
8.12
This clause is void
N/A
8.13
Adequate fastening of windows, lenses, lamp covers
etc. (pull test 20 N for 10 s)
etc. (pull test 20 N for 10 s)
N/A
8.14
Adequate fastening of covers (push/pull test 50 N for
10 s)
10 s)
N/A
8.15
No risk of damage to the insulation of internal wiring
due to hot parts or sharp edges
due to hot parts or sharp edges
The internal wiring does not
touch hot parts or sharp edges,
which may damage its
insulation and cause hazards.
touch hot parts or sharp edges,
which may damage its
insulation and cause hazards.
P
8.16
Only special supply equipment can be used
The apparatus is supplied from
AC mains.
AC mains.
N/A
8.17
Insulated winding wire without additional interleaved
insulation
insulation
N/A
8.18
Endurance test as required by 8.17
N/A
8.19
Disconnection from the mains
See below.
P
8.19.1
Disconnect device
The mains plug is used as the
disconnect device and see
also subclause 5.4.2.
disconnect device and see
also subclause 5.4.2.
P
All-pole switch or circuit breaker with >3mm contact
separation
separation
N/A
8.19.2
Mains switch ON indication
N/A
8.20
Switch not fitted in the mains cord
N/A
8.21
Bridging components comply with clause 14
N/A
8.22
Non-separable thin sheet material
N/A
9
Electric shock hazard under normal operating conditions
P
9.1
Testing on the outside
P
Click on the first or last page to see other SOUNDFLY BT (serv.man3) service manuals if exist.