JBL ON BEAT XTREME (serv.man8) EMC - CB Certificate ▷ View online
Page 17 of 42
Report No.: 171153
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
Conductive parts along reliably cemented joints
comply with 8.8
comply with 8.8
N/A
Temperature cycle test and dielectric strength test
N/A
13.7
Enclosed, enveloped or hermetically sealed parts not
conductively connected to the mains, clearances and
creepage distances as in table 12
conductively connected to the mains, clearances and
creepage distances as in table 12
No enclosed, enveloped or
hermetically sealed parts
hermetically sealed parts
N/A
13.8
Parts filled with insulating compound, meeting the
requirements of 8.8
requirements of 8.8
No parts filled with insulating
compound.
compound.
N/A
14 Components
14.1 Resistors
N/A
a) Resistors between hazardous live parts and
accessible metal parts
accessible metal parts
No such resistors
N/A
b) Resistors, other than between hazardous live
parts and accessible parts
parts and accessible parts
Bleeder resistor (R926)
connected between Line and
Neutral, located after fuse.
S-c of R926 resistor does not
cause infringement of the
requirement for operation under
fault conditions.
(Refer also to appended table,
fault condition tests and list of
critical components).
connected between Line and
Neutral, located after fuse.
S-c of R926 resistor does not
cause infringement of the
requirement for operation under
fault conditions.
(Refer also to appended table,
fault condition tests and list of
critical components).
N/A
Resistors separately approved ………….:
N/A
14.2
Capacitors and RC units
P
Capacitors separately approved …...……:
Yes, see below
P
14.2.1
Y capacitors tested to IEC 60384-14, 2
nd
edition :
Capacitor CY91, CY92, CY93
and CY94, certified according
to IEC 60384-14.
and CY94, certified according
to IEC 60384-14.
P
14.2.2
X capacitors tested to IEC 60384-14, 2
nd
edition :
Capacitor CX91 and CX92,
certified according to
IEC 60384-14.
certified according to
IEC 60384-14.
P
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 …………:
connected to the mains: tests for X2 …………:
No such capacitors
N/A
14.2.5
Capacitors with volume exceeding 1750 mm³, where
short-circuit current exceeds 0,2 A: compliance with
IEC60384-1, 4.38 category B or better ………:
short-circuit current exceeds 0,2 A: compliance with
IEC60384-1, 4.38 category B or better ………:
a) X-capacitor CX91, volume
exceeding 1750 mm³, but
tested to IEC384-14.
b) Several E. cap. Volume
exceeding 1750 mm³
but metal cases.
tested to IEC384-14.
b) Several E. cap. Volume
exceeding 1750 mm³
but metal cases.
N/A
Page 18 of 42
Report No.: 171153
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1, 4.38
category B or better ………………………:
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1, 4.38
category B or better ………………………:
a) X-capacitor CX91, volume
exceeding 1750 mm³, but
tested to IEC384-14.
b) Several E. cap. Volume
exceeding 1750 mm³
but metal cases.
tested to IEC384-14.
b) Several E. cap. Volume
exceeding 1750 mm³
but metal cases.
N/A
Shielded by a barrier acc. to 20.1.4/ table 21 or
metal …………………………………….:
metal …………………………………….:
N/A
14.3
Inductors and windings
P
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
(as relevant) and clause 20.1.4
Transformers evaluated
according to 14.3.3, 14.3.4
and 14.3.5
according to 14.3.3, 14.3.4
and 14.3.5
P
14.3.1
Transformers and inductors marked with
manufacturer's name and type ……………….:
manufacturer's name and type ……………….:
Adequate marking applied.
Mfr, ID and type no.
Mfr, ID and type no.
P
Transformers and inductors separately approved ….:
No.
N/A
14.3.2 General
Isolating transformers
P
Insulation material complies with clause 20.1.4
Considered. The insulation
material of isolating transf.
complies with flammability
category of Table 21.
material of isolating transf.
complies with flammability
category of Table 21.
P
14.3.3
Constructional requirements
P
14.3.3.1
Clearances and creepage distances comply with
clause 13
clause 13
(see appended table 13)
P
14.3.3.2
Transformers meet the constructional requirements
(see appended table 13)
P
14.3.4
Separation between windings
P
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible parts
(double or reinforced insulation) …………...:
between hazardous live parts and accessible parts
(double or reinforced insulation) …………...:
Reinforced insulation between
pr. and sec. windings according
to clause 8.8.
(see appended table 14.3.3)
pr. and sec. windings according
to clause 8.8.
(see appended table 14.3.3)
P
Coil formers and partition walls > 0,4 mm
> 0.4 mm.
P
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of
14.3.4.2 are met
protective screening only if all 7 conditions of
14.3.4.2 are met
Class II apparatus.
No such transformer used.
No such transformer used.
N/A
14.3.4.3
Separating transformers with at least basic insulation
Windings of Class II
construction used.
construction used.
N/A
14.3.5
Insulation between HAZARDOUS LIVE parts and
ACCESSIBLE parts
ACCESSIBLE parts
P
Page 19 of 42
Report No.: 171153
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
14.3.5.1
Class II transformers have adequate insulation
between hazardous live parts and accessible parts
(double or reinforced insulation)
between hazardous live parts and accessible parts
(double or reinforced insulation)
Double or reinforced insulation
between hazardous live
windings and accessible
conductive parts.
between hazardous live
windings and accessible
conductive parts.
P
Coil formers and partition walls > 0,4 mm
> 0.4 mm.
P
14.3.5.2
Class I transformers have adequate insulation
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
Winding of Class II
construction used.
construction used.
N/A
Winding wires connected to protective earth have
adequate current-carrying capacity
adequate current-carrying capacity
N/A
14.4
High voltage components
No high-voltage components.
N/A
High-voltage components and assemblies: U > 4 kV
(peak) separately approved
(peak) separately approved
N/A
Component meets category V-1 of IEC 60707
N/A
14.4.1
High voltage transformers and multipliers tested as
part of the submission
part of the submission
N/A
14.4.2
High voltage assemblies and other parts tested as
part of the submission
part of the submission
N/A
14.5
Protective devices
P
Protective devices used within their ratings
Mains fuse, F901
P
External clearances and creepage distances meet
requirement of clause 13 for the voltage across the
device when opened
requirement of clause 13 for the voltage across the
device when opened
Certified fuses used.
P
14.5.1.1
a) Thermal cut-outs separately approved
No thermal cut-outs.
N/A
b) Thermal cut-outs tested as part of the submission
N/A
14.5.1.2
a) Thermal links separately approved
No thermal links
N/A
b) Thermal links tested as part of the submission
N/A
14.5.1.3
Thermal devices re-settable by soldering
No thermal device
N/A
14.5.2.1
Fuse-links in the mains circuit according to IEC
60127
60127
Fuse is approved according
to IEC 60127.
to IEC 60127.
See appended table, list of
critical components.
critical components.
P
14.5.2.2
Correct marking of fuse-links adjacent to
holder ……:
holder ……:
The following marking applied;
F901: T 4A H 250V
F901: T 4A H 250V
P
Page 20 of 42
Report No.: 171153
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
14.5.2.3
Not possible to connect fuses in parallel …….:
No possible to connect fuses
in parallel.
in parallel.
N/A
14.5.2.4
Not possible to touch hazardous live parts when
replacing fuse-links without the use of a tool …..:
replacing fuse-links without the use of a tool …..:
No replacement of fuse
possible by hand.
possible by hand.
P
14.5.3
PTC thermistors comply with IEC 60730-1
No PTC’s thermistors.
N/A
PTC devices (15 W) category V-1 or better
N/A
14.5.4 Circuit
protectors
have adequate breaking capacity
and their position is correctly marked
Only standard fuses used.
N/A
14.6 Switches
N/A
14.6.1 a)
Separate testing to IEC 61058 including:
- 10 000 operations
- Normal pollution suitability
- Resistance to heat and fire level 3
- Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
No mains switch.
N/A
14.6.1 b)
Tested in the apparatus:
N/A
Switch controlling > 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.3, 14.6.4
and V-0 in annex G, G.1.1
> 35 V (peak)/24 V dc complying with 14.6.3, 14.6.4
and V-0 in annex G, G.1.1
N/A
Switch controlling > 0.2A with open contact voltage
< 35 V (peak)/24 V dc complying with 14.6.3 and V-0
in annex G, G.1.1
< 35 V (peak)/24 V dc complying with 14.6.3 and V-0
in annex G, G.1.1
N/A
Switch controlling < 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.4 and V-
0 in annex G, G.1.1
> 35 V (peak)/24 V dc complying with 14.6.4 and V-
0 in annex G, G.1.1
N/A
14.6.2
Switch tested to 14.6.1 b) constructed to IEC 61058-
1 subclause 13.1 and has making/breaking action
independent of speed of actuation
1 subclause 13.1 and has making/breaking action
independent of speed of actuation
N/A
14.6.3
Switch tested to 14.6.1 b) compliant with IEC 61058-
1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
N/A
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
strength
N/A
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 60058-1
additional tests to IEC 60058-1
N/A
Socket outlet current marking correct
No mains socket outlet
N/A
Click on the first or last page to see other ON BEAT XTREME (serv.man8) service manuals if exist.