JBL ON BEAT RUMBLE EMC - CB Certificate ▷ View online
Issue Date:
2013-01-09
Page 17 of 54
Report Reference #
E204594-A39-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
N/A
2.7.1
Basic requirements
Class III equipment.
N/A
Instructions when protection relies on building
installation
installation
N/A
2.7.2
Faults not covered in 5.3.7
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices:
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................... :
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
No interlocks provided.
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
Protection against extreme hazard
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches, relays and their related circuits
N/A
2.8.7.1
Separation distances for contact gaps and
their related circuits (mm) ......................... :
their related circuits (mm) ......................... :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
Issue Date:
2013-01-09
Page 18 of 54
Report Reference #
E204594-A39-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
2.9
Electrical insulation
Pass
2.9.1
Properties of insulating materials
N/A
2.9.2
Humidity conditioning
N/A
Relative humidity (%), temperature (°C) ... :
-
2.9.3
Grade of insulation
Unit supplied by SELV and no
hazardous voltage generated
within unit, only Functional
Insulation Required.
hazardous voltage generated
within unit, only Functional
Insulation Required.
Pass
2.9.4
Separation from hazardous voltages
N/A
Method(s) used ........................................ :
-
Issue Date:
2013-01-09
Page 19 of 54
Report Reference #
E204594-A39-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
2.10
Clearances, creepage distances and distances through insulation
Pass
2.10.1
General
Equipment supplied by SELV.
N/A
2.10.1.1 Frequency ................................................ :
N/A
2.10.1.2 Pollution degrees ..................................... :
N/A
2.10.1.3
Reduced values for functional insulation
N/A
2.10.1.4
Intervening unconnected conductive parts
N/A
2.10.1.5
Insulation with varying dimensions
N/A
2.10.1.6
Special separation requirements
N/A
2.10.1.7
Insulation in circuits generating starting pulses
N/A
2.10.2
Determination of working voltage
N/A
2.10.2.1
General
N/A
2.10.2.2
RMS working voltage
N/A
2.10.2.3
Peak working voltage
N/A
2.10.3
Clearances
Functional insulation
Pass
2.10.3.1
General
N/A
2.10.3.2
Mains transient voltages
N/A
a) AC mains supply .................................. :
N/A
b) Earthed d.c. mains supplies ................. :
N/A
c) Unearthed d.c. mains supplies ............. :
N/A
d) Battery operation .................................. :
N/A
2.10.3.3
Clearances in primary circuits
N/A
2.10.3.4
Clearances in secondary circuits
See 5.3.4 c
Pass
2.10.3.5
Clearances in circuits having starting pulses
N/A
2.10.3.6 Transients from a.c. mains supply ............ :
N/A
2.10.3.7 Transients from d.c. mains supply ............ :
N/A
2.10.3.8 Transients from telecommunication
networks and cable distribution systems .. :
N/A
2.10.3.9
Measurement of transient voltage levels
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply .......................... :
N/A
Issue Date:
2013-01-09
Page 20 of 54
Report Reference #
E204594-A39-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
For a d.c. mains supply ............................ :
N/A
b) Transients from a telecommunication network
N/A
2.10.4
Creepage distances
N/A
2.10.4.1
General
N/A
2.10.4.2
Material group and comparative tracking index
N/A
CTI tests ................................................... :
-
2.10.4.3
Minimum creepage distances
N/A
2.10.5
Solid insulation
N/A
2.10.5.1
General
N/A
2.10.5.2
Distances through insulation
N/A
2.10.5.3
Insulating compound as solid insulation
N/A
2.10.5.4
Semiconductor devices
N/A
2.10.5.5
Cemented joints
N/A
2.10.5.6
Thin sheet material - General
N/A
2.10.5.7
Separable thin sheet material
N/A
Number of layers (pcs) ............................. :
-
2.10.5.8
Non-separable thin sheet material
N/A
2.10.5.9
Thin sheet material - standard test procedure
N/A
Electric strength test ................................. :
-
2.10.5.10
Thin sheet material - alternative test procedure
N/A
Electric strength test ................................. :
-
2.10.5.11
Insulation in wound components
N/A
2.10.5.12
Wire in wound components
N/A
Working voltage ....................................... :
N/A
a) Basic insulation not under stress ......... :
N/A
b) Basic, supplementary, reinforced
insulation .................................................. :
insulation .................................................. :
N/A
c) Compliance with Annex U .................... :
N/A
Two wires in contact inside wound
component; angle between 45° and 90° .. :
component; angle between 45° and 90° .. :
N/A
Click on the first or last page to see other ON BEAT RUMBLE service manuals if exist.