JBL BALBOA SUB10 (serv.man2) EMC - CB Certificate ▷ View online
Page 41 of 44
Report Ref No.: 614376
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No.: IEC60065E
TRF Originator: ASTABEAB
National differences Ireland
IEC 60065:2001
(See also Group Differences)
CENELEC / IE 06 I
Equipment fitted with a flexible cable or cord provided with a 13 A plug in
accordance with Statutory Instrument 525:97
accordance with Statutory Instrument 525:97
P
National differences Italy
IEC 60065:2001
(See also Group Differences)
CENELEC / IT 06 I
5.1
Additional markings on the outside of the TV
receiver in Italian language
receiver in Italian language
N/A
User
instructions in Italian language including a
conformity declaration
N/A
Certification number on the back cover
N/A
Page 42 of 44
Report Ref No.: 614376
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No.: IEC60065E
TRF Originator: ASTABEAB
National
differences
SINGAPORE
IEC 60065:2001
NOTE: (These differences are taken from IEC 60065:1993 and adopted to
IEC 60065:2001)
CB / SG 2006 I
Throughout the standard,
whenever the words
"white pine board" appear, insert the words "or
plywood board" to it.
plywood board" to it.
P
SS143 Amendment No. 1 and No. 2
4.1.3
(4.1.3)*
Delete "45 % to 75 % and insert "65 ± 5 %".
75% maximum in IEC
60065:2001
60065:2001
P
7.1
(7.1)
Resistance to heat without external forces.
Adopt the temperature specified for the tropical
conditions.
conditions.
P
8.6
(9.3.4)
Delete the note "A Quality Assessment System
for capacitors complying with Subclause 14.2 is
under consideration in the IEC".
for capacitors complying with Subclause 14.2 is
under consideration in the IEC".
This is not in IEC 60065:2001
P
10.2
(10.2)
Humidity treatment
Adopt the testing conditions designed for tropical
conditions.
conditions.
120h at 93% rel. humidity
P
16
(16)
External flexible cords
Delete "IEC Publication 60227: Polyvinyl Chloride
Insulated Cables of Rated Voltages up to and
Including 450/750 V and IEC publication 60245:
Rubber insulated Cables of rated up to and
including 450/750 V " and insert "Singapore
Standard 236: Flexible Cords", whenever they
appear in this clause.
Insulated Cables of Rated Voltages up to and
Including 450/750 V and IEC publication 60245:
Rubber insulated Cables of rated up to and
including 450/750 V " and insert "Singapore
Standard 236: Flexible Cords", whenever they
appear in this clause.
Delete "CEE Publication 13, CEE Publication 2
and IEC Publication 60173: Colours of the Cores
of Flexible Cables and Cords" whenever they
appear in this clause.
and IEC Publication 60173: Colours of the Cores
of Flexible Cables and Cords" whenever they
appear in this clause.
P
16.2
(16.2)
Delete the notes in small print and insert "A
nominal cross-sectional area of 0.75 mm² will
satisfy this requirement".
nominal cross-sectional area of 0.75 mm² will
satisfy this requirement".
This is not in IEC 60065:2001
P
Page 43 of 44
Report Ref No.: 614376
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No.: IEC60065E
TRF Originator: ASTABEAB
16.3b
(16.4b)
Delete “Subclause 3.1 of IEC Publication 60227-2: Part
2: Test Methods“ and insert “Subclause 9.1 of SS 236“:
9.1 Flexing test (except for tinsel cords, twisted twin
and single core cords). The test shall be carried out by
means of the apparatus shown in Figure 5. This
apparatus has a carrier C supporting two pulleys A and
B arranged so that the cord is horizontal between the
pulleys. The carrier moves backward and forward over
a distance of 1 m at an approximately constant speed
of 0.33 m/s.
A sample of flexible cord about 5 m long shall be
stretched over the pulleys as shown in the figure, each
end being loaded with a weight. The weight and the
diameter of the pulleys A and B shall be given in Table
1.
2: Test Methods“ and insert “Subclause 9.1 of SS 236“:
9.1 Flexing test (except for tinsel cords, twisted twin
and single core cords). The test shall be carried out by
means of the apparatus shown in Figure 5. This
apparatus has a carrier C supporting two pulleys A and
B arranged so that the cord is horizontal between the
pulleys. The carrier moves backward and forward over
a distance of 1 m at an approximately constant speed
of 0.33 m/s.
A sample of flexible cord about 5 m long shall be
stretched over the pulleys as shown in the figure, each
end being loaded with a weight. The weight and the
diameter of the pulleys A and B shall be given in Table
1.
Screen cords in accordance with Table 7 shall be
tested before application of the screen and outer
sheath.
tested before application of the screen and outer
sheath.
The pulleys shall have a semi-circular shaped groove
for circular cords and a flat groove for parallel twin
cords. The restraining clamps D shall be fixed so that
the pull is always applied by the weight from which the
carrier is moving away. The carrier shall make 30 000
backward and forward movements (60 000 single
strokes). Each conductor of the sample shall be loaded
with the current specified in Table 2.
for circular cords and a flat groove for parallel twin
cords. The restraining clamps D shall be fixed so that
the pull is always applied by the weight from which the
carrier is moving away. The carrier shall make 30 000
backward and forward movements (60 000 single
strokes). Each conductor of the sample shall be loaded
with the current specified in Table 2.
For twin cords and for light PVC-sheated 3-core cords,
the voltage between the conductors shall be
approximately 230 V a.c. For all other cords having
three or more cores a three-phase a.c. voltage of about
400 V shall be applied to three conductors, any
additional conductors being connected to the neutral.
the voltage between the conductors shall be
approximately 230 V a.c. For all other cords having
three or more cores a three-phase a.c. voltage of about
400 V shall be applied to three conductors, any
additional conductors being connected to the neutral.
During the test no open-circuit in any core or short-
circuit between cores shall occur.
circuit between cores shall occur.
After the test, any sheath on cords having three or
more cores shall be removed. The cord, or the laid up
cores, shall then withstand the voltage test specified in
Subclause 8.2 or 8.3 as appropriate, but with a test
voltage not exceeding 2000 V.
more cores shall be removed. The cord, or the laid up
cores, shall then withstand the voltage test specified in
Subclause 8.2 or 8.3 as appropriate, but with a test
voltage not exceeding 2000 V.
TABLE 1, TABLE 2, FIGURES 4 and 5, see the
CB BULLETIN
P
* in parenthesis: clauses acc. to IEC 60065:1993
Page 44 of 44
Report Ref No.: 614376
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No.: IEC60065E
TRF Originator: ASTABEAB
National
differences
Korea
IEC 60065:2001
Information from Korea / KR 06 I I
National supply voltage are 110,220 and 380V
Rated 220-230V
P
Only appliances having supply frequency of
60Hz or a frequency range including 60Hz are
accepted
60Hz or a frequency range including 60Hz are
accepted
Rated 50-60Hz
P
5
Instruction manuals and marking related safety,
including name plate shall be in Korean or
graphical symbols in accordance with IEC
Publication 417.
including name plate shall be in Korean or
graphical symbols in accordance with IEC
Publication 417.
P
5.101 Addition
Other marking;
Wording “ “ ( See the CB Bulletine) or an
information regulated in IEC Publication 60417
giving high voltage warning to layman shall be
marked, if an apparatus contains a part more
than 600 volts.
information regulated in IEC Publication 60417
giving high voltage warning to layman shall be
marked, if an apparatus contains a part more
than 600 volts.
Tillgång till orden finns för
närvarande inte ännu
närvarande inte ännu
Access to the wording is for
the time being not available
the time being not available
N/A
15.1.1
Plugs for the connection of the apparatus to the
supply mains and socket outlets for providing
mains power to other apparatus shall comply with
the Korean requirements (KSC 8300 and 8305).
supply mains and socket outlets for providing
mains power to other apparatus shall comply with
the Korean requirements (KSC 8300 and 8305).
P
31
Radio frequency Interference
The apparatus shall comply with the relevant
CISPR requirements. (EMC=EMI + EMS)
CISPR requirements. (EMC=EMI + EMS)
Not checked
N/A
Click on the first or last page to see other BALBOA SUB10 (serv.man2) service manuals if exist.