DOWNLOAD Harman Kardon MAS 100-110 (serv.man2) Service Manual ↓ Size: 1.36 MB | Pages: 54 in PDF or view online for FREE

                                                                      Page 5 of 54                           Report No. SH09061297-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

3 GENERAL 

REQUIREMENTS 

 

 

Safety class of the apparatus ................................. : Class II apparatus 

Pass 

 
 

4 

GENERAL CONDITIONS OF TESTS 

 

4.1.4 Ventilation 

instructions 

require the use of the test 

box 

 N/A 

 
 

5 MARKING 

 

 

Comprehensible and easily discernible 

 

Pass 

 

Permanent durability against water and petroleum 
spirit 

After this test, the marking is 
legible; it is not easily possible 
to remove the marking plate 
and show no curling. 

Pass 

5.1 Identification, 

maker, 

model ................................... : MAS100, MAS110 

Pass 

 

Class II symbol if applicable 

On rear enclosure 

Pass 

 

Rated supply voltage and symbol .......................... : See marking plate 

Pass 

 

Frequency if safety dependant 

See marking plate 

Pass 

 

Rated current or power consumption .................... : See marking plate 

Pass 

5.2 

Earth terminal 

Class II equipment 

N/A 

 

Hazardous live terminals 

No Hazardous live terminal 

N/A 

 

Supply output terminals (other than mains) 

 

N/A 

5.3 

Use of triangle with exclamation mark 

On circuit diagram. 

Pass 

5.4 

Instructions for use 

 

Pass 

5.4.1 

Mains powered equipment not exposed to dripping 
or splashing. Warning concerning objects filled 
with liquid, etc. 

Adequate instructions 
provided. 

Pass 

 

Hazardous live terminals, instructions for wiring 

No hazardous live terminal 

N/A 

 

Instructions for replacing lithium battery 

No lithium battery 

N/A 

 

Instructions for modem if fitted 

No modem used. 

N/A 

 

Class I earth connection warning 

 

N/A 

 

Instructions for multimedia system connection 

Adequate instructions 
provided. 

Pass 

 

Special stability warning for fixed installation 

Not such equipment 

N/A 

                                                                      Page 6 of 54                           Report No. SH09061297-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

5.4.2 

Disconnect device: plug/coupler or all-pole mains 
switch location, accessibility and markings 

The appliance coupler is acting 
as disconnect device. The 
manual has suitable statement. 

Pass 

 

Instructions for permanently connected equipment Not permanently connected 

equipment.  

N/A 

 
 

6 HAZARDOUS 

RADIATION 

 

6.1 

Ionizing radiation < 36 pA/kg (0,5 mR/h) 

No ionizing radiation. 

N/A 

6.1 

EN 60065 

European Council Directive 96/29/Euratom of 13 
May 1996 10cm from outer surface of apparatus 
<1µSv/h (0,1mR/h) 

 N/A 

6.2 

Laser radiation, emission limits to IEC 60825-1  .... : Class 1 Laser 

Pass 

 

Emission limits under fault conditions .................... : Class 1 Laser 

Pass 

 
 

7 

HEATING UNDER NORMAL OPERATING CONDITIONS 

 

7.1 

Temperature rises not exceeding specified values, 
no operation of fuse links 

(see appended table) 

Pass 

7.1.1 

Temperature rise of accessible parts 

(see appended table) 

Pass 

7.1.2 

Temperature rise of parts providing electrical 
insulation 

(see appended table) 

Pass 

7.1.3 

Temperature rise of parts acting as a support or as 
a mechanical barrier 

(see appended table) 

Pass 

7.1.4 

Temperature rise of windings 

(see appended table) 

Pass 

7.1.5 

Parts not subject to a limit under 7.1.1 to 7.1.4 

(see appended table) 

Pass 

7.2 

Softening temperature of insulating material 
supporting parts conductively connected to the 
mains carrying a current > 0,2 A at least 150

 o

C 

(see appended table) 

Pass 

 
 

8 

CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION 
AGAINST ELECTRIC SHOCK 

 

8.1 

Conductive parts covered by lacquer, paper, 
untreated textile oxide films and beads etc. 
considered to be bare 

Windings and PCB are 
covered by lacquer and 
considered to be bare. 

Pass 

8.2 

No shock hazard when changing voltage setting 
device, fuse-links or handling drawers etc. 

Tools required. 

Pass 

8.3 

Insulation of hazardous live parts not provided by 
hygroscopic material 

 Pass 

                                                                      Page 7 of 54                           Report No. SH09061297-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

8.4 

No risk of electric shock following the removal of a 
cover which can be removed by hand 

No cover removable by hand. 

N/A 

8.5 

Class I equipment 

 

N/A 

 

Basic insulation between hazardous live parts and 
earthed accessible parts 

 N/A 

 

Resistors bridging basic insulation complying with 
14.2.1 a) 

 N/A 

8.6 

Class II equipment and Class II constructions 
within Class I equipment 

 Pass 

 

Reinforced or double insulation between 
hazardous live parts and accessible parts 

 Pass 

 

Components bridging reinforced or double 
insulation complying with 14.1 a) or 14.3 

Resistant: R54  

Transformer T4 and T5  

Pass 

 

Basic and supplementary insulation each being 
bridged by a capacitor complying with 14.2.1 a) 

Y2 capacitor: C2, C3 

X2 capacitor: C1, C5, C4, C13 

Pass 

 

Reinforced or double insulation being bridged with 
2 capacitors in series complying with 14.2.1 a) 

No such capacitor 

N/A 

 

Reinforced or double insulation being bridged with 
a single capacitor complying with 14.2.1 b) 

Y2 capacitor: C43, C42 

 

Pass 

 

Basic insulation bridged by components complying 
with 14.3.4.3 

 N/A 

8.7 

Basic insulation between parts at 35 V to 71 V 
(peak) a.c. or 60 V to 120 V d.c. and accessible 
parts 

 N/A 

 

Reinforced or double insulation between circuits 
operating at voltages between 35 V and 71 V 
(peak) a.c. or between 60 V and 120 V d.c. and 
hazardous live parts at higher voltage 

 N/A 

 

Separation by Class II isolating transformer 

 

N/A 

 

Separation by Class I transformer 

 

N/A 

 

Separation by earthed conductive part 

 

N/A 

8.8 

Basic or supplementary insulation > 0,4 mm (mm) : No such insulation used. 

N/A 

 

Reinforced insulation > 0,4 mm (mm) .................... : Bobbin  of transformer T4: Min. 

1.0mm  
Bobbin  of transformer T5: Min. 
1.0mm 

Pass 

 

Thin sheet insulation 

 

Pass 

                                                                      Page 8 of 54                           Report No. SH09061297-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

 

Basic or supplementary insulation, at least two 
layers, each meeting 10.3 

 N/A 

 

Basic or supplementary insulation, three layers any 
two of which meet 10.3 

 N/A 

 

Reinforced insulation, two layers each of which 
meet 10.3 

Two layers of insulating tape 
provided between primary 
winding and secondary 
winding of transformer, each 
layer comply with the 
requirement of 10.3. 

Pass 

 

Reinforced insulation, three layers any two which 
meet 10.3 

 N/A 

8.9 

Adequate insulation between internal hazardous 
live conductors and accessible parts 

Primary wiring: min. 0.4mm 

Pass 

 

Adequate insulation between internal hazardous 
live parts and conductors connected to accessible 
parts 

 Pass 

8.10 

Double insulation between conductors connected 
to the mains and accessible parts 

 Pass 

8.11 

Detaching of wires 

 

Pass 

 

No undue reduction of creepages or clearance 
distances if wires become detached 

All wires are fixed by double 
securement. 

Pass 

 Vibration 

test carried out  ........................................ : No, no need. 

N/A 

8.12 Void 

 

 

N/A 

8.13 

Adequate fastening of windows, lenses, lamp 
covers etc. (pull test 20 N for 10 s) 

 N/A 

8.14 

Adequate fastening of covers (pull test 50 N for 
10 s) 

Fastened by metal screws. 

Pass 

8.15 

No risk of damage to the insulation of internal 
wiring due to hot parts or sharp edges 

The internal lead wires are 
secured away from the hot 
parts and sharp edges by the 
construction. 

Pass 

8.16 

Only special supply equipment can be used 

 

N/A 

8.17 

Insulated winding wire without additional 
interleaved insulation 

 N/A 

8.18 

Endurance test as required by 8.17 

 

N/A 

8.19 

Disconnection from the mains 

See below. 

Pass 

8.19.1 Disconnect 

device 

Appliance coupler is used as 
the disconnect device. 

Pass