DOWNLOAD Harman Kardon HKTS 210SUB Service Manual ↓ Size: 1.5 MB | Pages: 56 in PDF or view online for FREE

Page 17 of 56 

 

Report No.1018947 

  

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

15.2 

N/A 

 

Accessible conductive parts of Class I equipment 
reliably connected to earth terminal, within 
equipment  

 N/A 

 

Protective earth conductors correctly coloured  

 

N/A 

 

Equipment with non-detachable mains cord 
provided with separate protective earth terminal 
near mains input  

 N/A 

 

Protective earth terminal resistant to corrosion  

 

N/A 

 

Earth resistance  test: < 0,1 

Ω at 25 A  ...................:   N/A 

15.3 

Terminals for external flexible cords and for 
permanent connection to the mains supply 

 N/A 

15.3.1 

Adequate terminals for connection of permanent 
wiring  

 N/A 

15.3.2 

P 

 

Not soldered to conductors of a printed circuit board   

P 

 

Adequate clearances and creepage distances 
between connections should a wire break away  

 P 

 

Wire secured by additional means to the  
conductor   

 P 

15.3.3 

Screws and nuts clamping conductors have 
adequate threads: ISO 261, ISO 262 or similar  

 N/A 

15.3.4 

Soldered conductors wrapped around terminal prior 
to soldering or held in place by additional means  

 N/A 

 

Clamping of conductor and insulation if not soldered 
or held by screws  

 N/A 

15.3.5 

Terminals allow connection of appropriate cross-
sectional area of conductors, for the rated current of 
the equipment  

 P 

15.3.6 

Terminals to 15.3.3 have sizes required by table 16   N/A 

15.3.7 

Terminals clamp conductors between metal and 
have adequate pressure  

 N/A 

 

Terminals designed to avoid conductor slipping out 
when tightened or loosened  

 N/A 

 

Terminals adequately fixed to avoid loosening when 
the clamping is tightened or loosened and stress on 
internal wiring is avoided  

 N/A 

15.3.8 

Terminals carrying a current more than 0,2 A: 
contact pressure not transmitted by insulating 
material except ceramic  

 N/A 

Page 18 of 56 

 

Report No.1018947 

  

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

15.3.9 

Termination of non-detachable cords: wires 
terminated near to each other  

 P 

 

Terminals located and shielded: test with 8 mm 
strand  

 P 

15.4 

N/A 

15.4.1 

No undue strain on mains socket-outlets  

 

N/A 

15.4.2 

Device complies with standard for dimensions of 
mains plugs  

 N/A 

15.4.3 

Device has adequate mechanical strength (tests 
a,b,c)  

 N/A 

 

16.1 

Mains cords sheathed type, complying with 
IEC 60227 for PVC or IEC 60245 for synthetic 
rubber cords ............................................................: 

PVC P 

 

Non-detachable cords for Class I have green/yellow 
core for protective earth  

 N/A 

16.2 

Mains cords conductors have adequate cross-
sectional area for rated current consumption of the 
equipment  

2 x 0.75 mm

2

 P 

16.3 

a) Flexible cords not complying with 16.1, used for 
interconnections between separate units of 
equipment used in combination and carrying 
hazardous live voltages, have adequate dielectric 
strength  

 N/A 

 

b) Flexible cords not complying with 16.1, withstand 
bending and mechanical stress (3.2 of 
IEC 60227-2)  

 N/A 

16.4 

Flexible cords used for connection between 
equipment have adequate cross-sectional areas to 
avoid temperature rise under normal and fault 
conditions  

 N/A 

16.5 

Adequate strain relief on external flexible cords  

 

P 

 

Not possible to push cord back into equipment  

 

P 

 

Strain relief device unlikely to damage flexible  
cord  

 P 

 

For mains cords of Class I equipment, hazardous 
live conductors become taut before earth conductor 

 N/A 

16.6 

Apertures for external flexible cord: no risk of 
damage to the cord during assembly or movement 
in use  

 P 

Page 19 of 56 

 

Report No.1018947 

  

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

16.7 

Transportable musical instruments and amplifiers 
fitted with detachable cord set with appliance inlet to 
IEC 60320-1  

 N/A 

 

Transportable musical instruments and amplifiers 
fitted with detachable cord sets or with means of 
stowage to protect the cord  

 N/A 

 

17.1 

 

 

- screws into metal: 5 times 

 

N/A 

 

- screws into non-metallic material: 10 times  

 

P 

17.2 

Correct introduction into female threads in non-
metallic material  

 N/A 

17.3 

Cover fixing screws: captive  

 

N/A 

 

Non-captive fixing screws: no hazard when 
replaced by a screw whose length is 10 times its 
diameter  

 P 

17.4 

No loosening of conductive parts carrying a current 
> 0,2 A  

 P 

17.5 

Contact pressure not transmitted through plastic 
other than ceramic for connections carrying a 
current > 0,2 A  

 P 

17.6 

Stranded conductors of flexible supply cords 
carrying a current > 0,2 A with screw terminals not 
consolidated by solder  

 N/A 

17.7 

Cover fixing devices other than screws have 
adequate strength and their positioning is 
unambiguous  

 N/A 

17.8 

Fixing devices for detachable legs or stands  
provided  

 N/A 

17.9 

Internal pluggable connections, affecting safety, 
unlikely to become disconnected  

 P 

 

Page 20 of 56 

 

Report No.1018947 

  

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

 

Picture tube separately approved to IEC 61965  ....:   

N/A 

 

Picture tube separately approved to 18.1  ..............:   

N/A 

18.1 

Picture tubes >16 cm intrinsically protected  

 

N/A 

 

Non-intrinsically protected tubes >16 cm used with 
protective screen  

 N/A 

 

Protective film as part of implosion protection: 
edges covered by enclosure  

 N/A 

18.2 

Intrinsically protected tubes: tests on 12 samples  

 

N/A 

18.2.1 

Samples subject to ageing: 6 samples  

 

N/A 

18.2.2 

Samples subject to implosion test: 6 samples  

 

N/A 

18.2.3 

Samples subject to mechanical strength test (steel 
ball): 6 samples  

 N/A 

18.3 

Non-intrinsically protected tubes tested to 18.3  

 

N/A 

 

 

Mass of the equipment exceeding 7 kg ..................:  Yes 

P 

 

Apparatus intended to be fastened in place – 
suitable instructions .................................................: 

 N/A 

19.1 

Test on a plane, inclined at 10

o

 to the horizontal  

 

P 

19.2 

100 N force applied vertically downwards  

 

N/A 

19.3 

100 N force, or 13% of weight, applied horizontally 
to point of least stability  

 P 

19.4 

Edges or corners not hazardous  

 

P 

19.5 

Glass surfaces (exc.laminated) with an area 
exceeding 0,1 m² or maximum dimension 
> 450 mm, pass the test of 19.5.1  

 N/A 

19.6 

Wall or ceiling mountings adequate  

 

N/A