Harman Kardon BDS 577 EMC - CB Certificate ▷ View online
Page 9 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
AU Australia
AU
20.201.2.
2
2
Testing of insulated parts
Part of insulating material supporting potential ignition sources shall be subject to the
glow-wire test of AS/NZS 64695.2.11 which shall be carried out at 750°C.
glow-wire test of AS/NZS 64695.2.11 which shall be carried out at 750°C.
The test shall be also carried out on other parts of insulating material which are within a
distance of 3 mm of the connection
distance of 3 mm of the connection
NOTE
– Contacts in components such as switch contacts are considered to be
connections.
For parts which withstand the glow-wire test but produce a flame, other parts above the
connection within the envelope of a vertical cylinder having a diameter of 20 mm and a
height of 50 mm shall be subjected to the needle-flame test. However, parts shielded by
a barrier which meets the needle-flame test need not be tested.
connection within the envelope of a vertical cylinder having a diameter of 20 mm and a
height of 50 mm shall be subjected to the needle-flame test. However, parts shielded by
a barrier which meets the needle-flame test need not be tested.
The needle-flame test shall be made in accordance with AS/NZS 4695.2.2 with the
following modifications:
following modifications:
Clause of AS/NZS 4695.2.2
Change
5 Severities
Replace with:
The duration of application of the test flame shall be
30 s
30 s
1 s.
8 Test procedure
8.2
8.4
Replace the first sentence with:
The specimen shall be arranged so that the flame can
be applied to a vertical or horizontal edge as shown in
the examples of figure 1.
be applied to a vertical or horizontal edge as shown in
the examples of figure 1.
The first paragraph does not apply.
Addition:
If possible, the flame shall be applied at least 10 mm
from a corner.
from a corner.
8.5
Replace with:
The test shall be made on one specimen. If the
specimen does not withstand the test, the test may be
repeated on two further specimens, both of which
shall then withstand the test
specimen does not withstand the test, the test may be
repeated on two further specimens, both of which
shall then withstand the test
10 Evaluation of test
results
results
Replace with:
The duration of burning (tb) shall not exceed 30 s.
However, for printed circuit boards, it shall not exceed
15 s.
However, for printed circuit boards, it shall not exceed
15 s.
The needle-flame test shall not be carried out on parts of material classified as V-0 or V-
1 according to AS/NZS 60695.11.10 provided that the sample tested was not thicker
than the relevant part.
1 according to AS/NZS 60695.11.10 provided that the sample tested was not thicker
than the relevant part.
N/A
Page 10 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
AU Australia
AU
20.201.2.
3
3
Testing by needle-flame test
If parts, other than enclosures, do not withstand
the glow wire tests of 20.201.2.2, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
20.201.2.2 shall be made on all parts of non-
metallic material which are within a distance of
50 mm or which are likely to be impinged upon by
flame during the tests of 20.201.2.2. Parts
shielded by a separate barrier which meets the
needle-flame test shall not be tested.
the glow wire tests of 20.201.2.2, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
20.201.2.2 shall be made on all parts of non-
metallic material which are within a distance of
50 mm or which are likely to be impinged upon by
flame during the tests of 20.201.2.2. Parts
shielded by a separate barrier which meets the
needle-flame test shall not be tested.
NOTE 1
– If the enclosure does not withstand the
glow-wire test the appliance is considered to have
failed to meet the requirements of Clause 21.201
without the need for consequential testing.
failed to meet the requirements of Clause 21.201
without the need for consequential testing.
NOTE 2
– If other parts do not withstand the glow-
wire test due to ignition of the tissue paper and if
this indicates that burning or glowing particles can
fall onto an external surface underneath the
apparatus, the apparatus is considered to have
failed to meet the requirements of Clause 21.201
without the need for consequential testing
this indicates that burning or glowing particles can
fall onto an external surface underneath the
apparatus, the apparatus is considered to have
failed to meet the requirements of Clause 21.201
without the need for consequential testing
NOTE 3
– Parts likely to be impinged upon by the
flame are considered to be those within the
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting, in contact with, or in close proximity to,
connections.
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting, in contact with, or in close proximity to,
connections.
N/A
Page 11 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
AU Australia
AU
20.201.2.
4
4
Testing of printed boards
The base material of printed boards shall be
subject to the needle-flame test of
Clause 21.201.2.3. The flame shall be applied to
the edge of the board where the heatsink effect is
lowest when the board is positioned as in normal
use. The flame shall not be applied to an edge
consisting of broken perforations, unless the edge
is less than 3 mm from a potential ignition source.
subject to the needle-flame test of
Clause 21.201.2.3. The flame shall be applied to
the edge of the board where the heatsink effect is
lowest when the board is positioned as in normal
use. The flame shall not be applied to an edge
consisting of broken perforations, unless the edge
is less than 3 mm from a potential ignition source.
The test is not carried out if the
—
- printed board does not carry any potential
ignition source;
ignition source;
- base material of printed boards, on which the
available power at a connection exceeds 15 VA
operating at a voltage exceeding 50 V and equal
or less than 400 V (peak) a.c. or d.c. under normal
operating conditions, is of flammability category V-
1 or better according to AS/NZS 60695.11.10, or
the printed boards are protected by an enclosure
meeting the flammability category V-0 according
to AS/NZS 60695.11.10, or made of metal, having
openings only for connecting wires which fill the
openings completely; or
available power at a connection exceeds 15 VA
operating at a voltage exceeding 50 V and equal
or less than 400 V (peak) a.c. or d.c. under normal
operating conditions, is of flammability category V-
1 or better according to AS/NZS 60695.11.10, or
the printed boards are protected by an enclosure
meeting the flammability category V-0 according
to AS/NZS 60695.11.10, or made of metal, having
openings only for connecting wires which fill the
openings completely; or
- base material of printed boards, on which the
available power at a connection exceeds 15 VA
operating at a voltage exceeding 400 V (peak) a.c.
or d.c. under normal operating conditions, and
base material of printed boards supporting spark
gaps which provides protection against
overvoltages, is of flammability category V-0
according to AS/NZS 60695.11.10 or the printed
boards are contained in a metal enclosure, having
openings only for connecting wires which fill the
openings completely.
available power at a connection exceeds 15 VA
operating at a voltage exceeding 400 V (peak) a.c.
or d.c. under normal operating conditions, and
base material of printed boards supporting spark
gaps which provides protection against
overvoltages, is of flammability category V-0
according to AS/NZS 60695.11.10 or the printed
boards are contained in a metal enclosure, having
openings only for connecting wires which fill the
openings completely.
Compliance shall be determined using the
smallest thickness of the material.
smallest thickness of the material.
NOTE
– Available power is the maximum power
which can be drawn from the supplying circuit
through a resistive load whose value is chosen to
maximize the power for more than 2 min when the
circuit supplied is disconnected.
through a resistive load whose value is chosen to
maximize the power for more than 2 min when the
circuit supplied is disconnected.
N/A
20.201.3 For open circuit voltages greater than 4 kV
Potential ignition sources with open circuit
voltages exceeding 4 kV (peak) a.c. or d.c. under
normal operating conditions shall be contained in
a fire enclosure which shall comply with
flammability category V-1 or better according to
AS/NZS 60695.11.10.
voltages exceeding 4 kV (peak) a.c. or d.c. under
normal operating conditions shall be contained in
a fire enclosure which shall comply with
flammability category V-1 or better according to
AS/NZS 60695.11.10.
N/A
Page 12 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
AU Australia
AU
Annex B
After the heading add:
For Australia only, this Annex is replaced by the
requirements of the Telecommunications
Labelling Notice issued under the
Telecommunications Act.
requirements of the Telecommunications
Labelling Notice issued under the
Telecommunications Act.
NOTE
– The Telecommunications Act is
administered by the Australian Communications
Authority.
Authority.
N/A
Click on the first or last page to see other BDS 577 service manuals if exist.