Harman Kardon AVR 155 (serv.man2) EMC - CB Certificate ▷ View online
- Page 27 of 43 -
Report
No.
97240
17.4
No loosening of conductive parts carrying a
current > 0,2 A
current > 0,2 A
Loosening is sufficiently
prevented
prevented
P
17.5
Contact pressure not transmitted through plastic
other than ceramic for connections carrying a
current > 0,2 A
other than ceramic for connections carrying a
current > 0,2 A
No contact pressure
transmitted through
insulating material.
transmitted through
insulating material.
P
17.6
Stranded conductors of flexible supply cords
carrying a current > 0,2 A with screw terminals not
consolidated by solder
carrying a current > 0,2 A with screw terminals not
consolidated by solder
No screw terminals.
N/A
17.7
Cover fixing devices other than screws have
adequate strength and their positioning is
unambiguous
adequate strength and their positioning is
unambiguous
No cover fixing devices
other than screws
other than screws
N/A
17.8
Fixing devices for detachable legs or stands
provided
provided
No detachable provided
N/A
17.9
Internal pluggable connections, affecting safety,
unlikely to become disconnected
unlikely to become disconnected
Connections complies,
checked by inspection
checked by inspection
P
18
MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST
THE EFFECTS OF IMPLOSION
THE EFFECTS OF IMPLOSION
Picture tube separately approved to IEC 61965:
No picture tube.
N/A
Picture tube separately approved to 18.1 ..........
N/A
18.1
Picture tubes > 16 cm intrinsically protected
N/A
Non-intrinsically protected tubes > 16 cm used
with protective screen
with protective screen
N/A
Protective film as part of implosion protection:
edges covered by enclosure
edges covered by enclosure
N/A
18.2
Intrinsically protected tubes: tests on 12 samples
N/A
18.2.1
Samples subject to ageing: 6
N/A
18.2.2
Samples subject to implosion test: 6
N/A
18.2.3
Samples subject to mechanical strength test
(steel ball): 6
(steel ball): 6
N/A
18.3
Non-intrinsically protected tubes tested to 18.3
N/A
- Page 28 of 43 -
Report
No.
97240
19
STABILITY AND MECHANICAL HAZARDS
Mass of the equipment exceeding 7 kg ............. :
Weight: 10,5 kg
⎯
Apparatus intended to be fastened in place –
suitable instructions
suitable instructions
No
N/A
19.1
Test on a plane, inclined at 10
o
to the horizontal
Tested on a plane inclined
at an angle of 10°
at an angle of 10°
P
19.2
100 N force applied vertically downwards
100N force have no
influence on the stability
influence on the stability
P
19.3
100 N force, or 13% of weight, applied horizontally
to point of least stability.
to point of least stability.
< 25 kg, < 1M
N/A
19.4
Edges or corners not hazardous
There is no hazardous
edges or corners when the
apparatus is operating in
normal position
edges or corners when the
apparatus is operating in
normal position
P
19.5
Glass surfaces (exc.laminated) with an area
exceeding 0,1 m² or maximum dimension
> 450 mm, pass the test of 19.5.1
exceeding 0,1 m² or maximum dimension
> 450 mm, pass the test of 19.5.1
No glass surface.
N/A
19.6
Wall or ceiling mountings adequate
No wall or ceiling
mountings.
mountings.
N/A
20
RESISTANCE TO FIRE
20.1
Electrical components and mechanical parts
P
a) Exemption for components contained in an
enclosure of material V-0 to IEC
enclosure of material V-0 to IEC
60695-11-10
with
openings not exceeding 1 mm in width
.
N/A
b) Exemption for small components as defined in
20.1
20.1
PCB are of flammability
class V-0 and exception is
made for small components
class V-0 and exception is
made for small components
P
20.1.1 Electrical
components
meet the requirements of
Clause 14 or 20.1.4
Electrical components
comply with flammability
requirements in clause 14.
comply with flammability
requirements in clause 14.
P
20.1.2
Insulation of internal wiring working at voltages
> 4 Kv or leaving an internal fire enclosure,
> 4 Kv or leaving an internal fire enclosure,
or
located within the areas mentioned in Table 21,
not contributing to the spread of fire
No wires working at
voltages > 4kV or leaving
an internal fire enclosure
voltages > 4kV or leaving
an internal fire enclosure
N/A
- Page 29 of 43 -
Report
No.
97240
20.1.3
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c. meets
V-1 or better to IEC60707, unless used in a fire
enclosure
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c. meets
V-1 or better to IEC60707, unless used in a fire
enclosure
All PCB are of base
material with flammability
category V-0 or better.
See appended table
material with flammability
category V-0 or better.
See appended table
P
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage >400 V
(peak) a.c. or d.c. meets V-0 to IEC 60707
available power exceeds 15 W at a voltage >400 V
(peak) a.c. or d.c. meets V-0 to IEC 60707
No voltage exceeding
400V (peak) a.c. or d.c.
400V (peak) a.c. or d.c.
N/A
20.1.4
Components and parts not covered by 20.1.1,
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
No such components
N/A
Components and parts as above but shielded
from a potential ignition source, with the barrier
area in accordance with Table 21 and fig. 13
from a potential ignition source, with the barrier
area in accordance with Table 21 and fig. 13
No such components
N/A
Apparatus with voltages >4kV under normal
operating conditions and distances to the
enclosure exceed those specified Table 21,
flammability classification HB40 or better is
required for the enclosure.
operating conditions and distances to the
enclosure exceed those specified Table 21,
flammability classification HB40 or better is
required for the enclosure.
Normal operating voltage
is
is
< 4KV
N/A
20.2 Fire
enclosure
N/A
20.2.1
Potential ignition sources with open circuit
voltage > 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
voltage > 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
No voltages exceeding
4kV, no fire enclosure
requirement
4kV, no fire enclosure
requirement
N/A
20.2.2
Internal fire enclosures with openings not
exceeding 1 mm in width and with openings for
wires completely filled
exceeding 1 mm in width and with openings for
wires completely filled
No internal fire enclosure.
N/A
20.2.3
Requirements of 20.2.1 and 20.2.2 met by an
internal fire enclosure
internal fire enclosure
No internal fire enclosure.
N/A
- Page 30 of 43 -
Report
No.
97240
A
APPENDIX A, ADDITIONAL REQUIREMENTS FOR APPARATUS WITH
PROTECTION AGAINST SPLASHING WATER
PROTECTION AGAINST SPLASHING WATER
A.5.1
j) Marked with IPX4 (IEC 60529), 5.4.1 a) does
not apply
not apply
Not intended for outdoor use
N/A
A.10.2.1
Enclosure provides protection against
splashing water
splashing water
N/A
A.10.2.2
Humidity treatment carried out for 7 days
See clause above
N/A
B
APPENDIX B, APPARATUS TO BE CONNECTED TO THE
TELECOMMUNICATION NETWORKS
TELECOMMUNICATION NETWORKS
Complies with IEC 62151 clause 1
No TNV circuits
N/A
Complies with IEC 62151 clause 2
N/A
Complies with IEC 62151 clause 3 but with
3.5.4 modified to 2.4.10 of this standard
3.5.4 modified to 2.4.10 of this standard
N/A
Complies with IEC 62151 clause 4 but with
4.1.2, 4.1.3 and 4.2.1.2 modified in accordance
with annex B of this standard
4.1.2, 4.1.3 and 4.2.1.2 modified in accordance
with annex B of this standard
N/A
Complies with IEC 62151 cause 5 but with 5.3.1
modified in accordance with annex B of this
standard
modified in accordance with annex B of this
standard
N/A
Complies with IEC 62151 clause 6
N/A
Complies with IEC 62151 clause 7
N/A
Complies with IEC 62151 annex A, B and C
N/A
Click on the first or last page to see other AVR 155 (serv.man2) service manuals if exist.