Harman Kardon AVR 134 (serv.man2) EMC - CB Certificate ▷ View online
Page 10 of 22
Report Ref. No. 077-204389-000
Clause Requirement
− Test
Result
− Remark
Verdict
TRF No. IECEN60065G
15.1.1
Apparatus which is fitted with a flexible cable or
cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets
etc. (Safety) Regulations 1994, unless exempted
by those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved
conversion plug.
Justification:
SI 1768: 1994
cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets
etc. (Safety) Regulations 1994, unless exempted
by those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved
conversion plug.
Justification:
SI 1768: 1994
P
NO
13.3.1
To the second paragraph the following is added:
In Norway, due to the IT power distribution
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault. Justification: Based on a use in Norway of
an IT power distribution system where the neutral
is not provided.
In Norway, due to the IT power distribution
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault. Justification: Based on a use in Norway of
an IT power distribution system where the neutral
is not provided.
N/A
Page 11 of 22
Report Ref. No. 077-204389-000
Clause Requirement
− Test
Result
− Remark
Verdict
TRF No. IECEN60065G
15.1.1
Mains socket-outlets mounted on CLASS II
apparatus shall comply with the specifications
given in CEE Publ. 7 as fas as a Applicable, with
the following amendments:
§ 8 Dimensions
a 2,5 A 250 V two-pole socket-outlets for
electronic apparatus shall comply with the
enclosed Standard Sheet I.
apparatus shall comply with the specifications
given in CEE Publ. 7 as fas as a Applicable, with
the following amendments:
§ 8 Dimensions
a 2,5 A 250 V two-pole socket-outlets for
electronic apparatus shall comply with the
enclosed Standard Sheet I.
§ 24 Mechanical strength
a 2,5 A, 250 V socket-outlets for CLASS II
electronic apparatus are tested as specified in
12.1.3 of EN 60065.
Also the protecting rim shall be tested.
Justification:
Act of 24 May 1929 relating to supervision of
electrical installation (TEA 1929/FEL 1998).
a 2,5 A, 250 V socket-outlets for CLASS II
electronic apparatus are tested as specified in
12.1.3 of EN 60065.
Also the protecting rim shall be tested.
Justification:
Act of 24 May 1929 relating to supervision of
electrical installation (TEA 1929/FEL 1998).
N/A
J.2
After Table J.1 the following is added: In Norway,
due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be
equal to the line-to-line voltage, and will remain
230 V in case of a single earth fault. Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be
equal to the line-to-line voltage, and will remain
230 V in case of a single earth fault. Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
N/A
Annex B
Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Add the following:
All subclauses given below are subclauses of IEC
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Add the following:
All subclauses given below are subclauses of IEC
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
N/A
Page 12 of 22
Report Ref. No. 077-204389-000
Clause Requirement
− Test
Result
− Remark
Verdict
TRF No. IECEN60065G
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
NOTE – In Norway, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket –outlet.
The marking text shall be as follows:
“Apparatet skal tilkoples jordet stikkontakt”
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
Add after the first paragraph:
NOTE – In Norway, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket –outlet.
The marking text shall be as follows:
“Apparatet skal tilkoples jordet stikkontakt”
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
N/A
NOTE 1 In Finland, Norway and Sweden, there
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
N/A
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
forming part of a component, it shall at least
consist of either
-
two layers of thin sheet material,
each of which shall pass the electric
strength test below, or – one layer
having a distance through insulation
of at least 0,4 mm, which shall pass
the electric strength test below.
each of which shall pass the electric
strength test below, or – one layer
having a distance through insulation
of at least 0,4 mm, which shall pass
the electric strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
N/A
Page 13 of 22
Report Ref. No. 077-204389-000
Clause Requirement
− Test
Result
− Remark
Verdict
TRF No. IECEN60065G
-
passes the test and inspection
criteria of 13.6 with an electric
strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6,
and
criteria of 13.6 with an electric
strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6,
and
- is subject to routine testing for electric strength
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
N/A
A capacitor classified Y3 according to IEC 60384-
14:1993, may bridge this insulation under the
following conditions:
14:1993, may bridge this insulation under the
following conditions:
-
the insulation requirements are
satisfied by having a capacitor
classified Y3 as defined by IEC
60384-14, which in addition
to the Y3 testing, is tested with an
Impulse test of 2.5kV defined in IEC
62151, subclause 6.2.1;
satisfied by having a capacitor
classified Y3 as defined by IEC
60384-14, which in addition
to the Y3 testing, is tested with an
Impulse test of 2.5kV defined in IEC
62151, subclause 6.2.1;
-
the additional testing shall be
performed on all the test specimens
as described in IEC 60384-14;
performed on all the test specimens
as described in IEC 60384-14;
- the Impulse test of 2.5kV is to be performed
before the Endurance Test in IEC 60384-14 in the
sequence of tests as
described in IEC 60384-14.
before the Endurance Test in IEC 60384-14 in the
sequence of tests as
described in IEC 60384-14.
N/A
Subclause 5.3.2 (Corrigendum 1):
Add after the fourth dash:
NOTE –In Norway, exclusions are applicable for
equipment which is intended for connection to the
building installation
wiring using screw terminals or other reliable
means, and for equipment which is intended for
connection to the building installation wiring via an
industrial plug and socket –outlet or an appliance
coupler, or both, complying with IEC 60309 or
with a comparable national standard.
Add after the fourth dash:
NOTE –In Norway, exclusions are applicable for
equipment which is intended for connection to the
building installation
wiring using screw terminals or other reliable
means, and for equipment which is intended for
connection to the building installation wiring via an
industrial plug and socket –outlet or an appliance
coupler, or both, complying with IEC 60309 or
with a comparable national standard.
N/A
SE
Click on the first or last page to see other AVR 134 (serv.man2) service manuals if exist.