Sony KDL-32XBR4 / KDL-40D3000 Service Manual ▷ View online
37
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
LVDS CABLE - BU BOARD TO BH BOARD
1. Attach HDMI Connector to BU-Bd
(CN5502).
2. GENTLY fold over cables to right side.
3 CONFIRM Color of Sticker (RED)
4. After Installing DTT Top apply 3x5mm
screw to GND Ring on HDMI Assy.
TORQUE: 6kg.cm (+-1.0kg.cm)
OPERATION PROCESS
TORQUE SPECIFICATION
Install HDMI Cable on BU-Bd
(CN5504)
NOTE: COLOR OF Round
Sticker
(CN5504)
NOTE: COLOR OF Round
Sticker
(RED)
.
BEFORE Installing DTT Shield
Top,
Top,
GENTLY fold cables over
towards right as shown.
towards right as shown.
Too much pressure applied to
cable/connector when folding
cables over to right side WILL
damage the connector!!
cable/connector when folding
cables over to right side WILL
damage the connector!!
After DTT Shield Top installation, use
3x5mm screw to secure GND tab on
HDMI Harness.
3x5mm screw to secure GND tab on
HDMI Harness.
NOTE:
SIDE HDMI Cable will have conductive
tape wrapping on PP/MP parts.
Running change to eliminate tape wrapping.
tape wrapping on PP/MP parts.
Running change to eliminate tape wrapping.
2
1
3
4
38
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
1. Route 40P LVDS Cable between
BU-Bd and TCON as shown.
2. Apply 3x8mm Screw (2-places) to ground
LVDS cable.
Put Attention on Routing of Cable.
G1 to BU cables are on TOP of LVDS.
H3-Bd cables are UNDER LVDS.
G1 to BU cables are on TOP of LVDS.
H3-Bd cables are UNDER LVDS.
3mm TORQUE: 6.0kg-cm (+-1.0kg-cm)
OPERATION PROCESS
TORQUE SPECIFICATION
NOTE: LVDS Cable is OVER ALL cables
Apply 3X8mm screw
when installing DTT Shield Top
when installing DTT Shield Top
1
2
2
Apply 3X8mm screw
when installing BH Shield Top
when installing BH Shield Top
CAUTION:
NOTE COLOR OF TAPE ON LVDS HARNESS!
PROPER COLOR IS WHITE.
*LVDS HAS 2 GROUNDING TABS!
PROPER COLOR IS WHITE.
*LVDS HAS 2 GROUNDING TABS!
Not used in final design
LVDS CABLE - BH BOARD TO TCON
39
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
1. Route 40P LVDS Cable between
BU-Bd and TCON as shown.
2. Apply 3x8mm Screw to BH Shield Top.
(When Installing BH Shield top)
Put Attention on Routing of Cable.
Put Attention on TCON END of Cable
to make shure cable end does NOT
Put Attention on TCON END of Cable
to make shure cable end does NOT
touch panel(see photo of side of cable)
3mm TORQUE: 6.0kg-cm (+-1.0kg-cm)
OPERATION PROCESS
TORQUE SPECIFICATION
Apply 3x8mm Screw to Ground Tab on LVDS.
CAUTION:
NOTE Ground Tab on LVDS is
BELOW BH Shield Top Tab!
BELOW BH Shield Top Tab!
1
2
CAUTION:
NOTE COLOR of Tape on LVDS
WHITE is Correct Color.
*LVDS Has 1 Ground Tab.
WHITE is Correct Color.
*LVDS Has 1 Ground Tab.
CAUTION:
DO NOT allow TCON END of cable to
touch panel!
This is NG for EMI.
touch panel!
This is NG for EMI.
O.K. !
LVDS CABLE - BU BOARD
40
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
Route LVDS Harness from BU-Board
(CN4500) as shown.
(CN4500) as shown.
CAUTION: Keep LVDS Wires AWAY from
Memory IC and JIG Connectors!
Memory IC and JIG Connectors!
OPERATION PROCESS
CAUTION:
Keep LVDS Cables AWAY from JIG Connectors
and Memory IC.
HDMI CABLE
Click on the first or last page to see other KDL-32XBR4 / KDL-40D3000 service manuals if exist.