Sony KDL-32XBR4 / KDL-40D3000 Service Manual ▷ View online
25
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
H3 BOARD HARNESS (CONTINUED)
Apply Sheet Core C to edge of Panel to
cover sharp edge of panel.
Use ribs on bezel (w/o screw boss) as a
guide to center tape.
cover sharp edge of panel.
Use ribs on bezel (w/o screw boss) as a
guide to center tape.
OPERATION PROCESS
1
2
Apply LCD Tape to hold BOTH
Rt. Speaker and H4 wires.
Rt. Speaker and H4 wires.
3
26
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
H4 BOARD
1. Install H4-Bd BEFORE Installing the
speakers/baffles.
2. Apply LCD Tape on SIDE of the magnet
on Rt. Speaker to hold the H4 Cables.
3. MAKE SURE there is slack in the cable
between the H4 Connector and LCD Tape.
Tension on the cable will cause the
Connector to lift or break.
Tension on the cable will cause the
Connector to lift or break.
OPERATION PROCESS
1
2
3
27
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
H4 BOARD AND RIGHT SPEAKER
Wire Dress Rt. Speaker wires and H4
cables in G-Bracket clips.
NOTE: Rt. Spkr. Wires are NOT dressed
cables in G-Bracket clips.
NOTE: Rt. Spkr. Wires are NOT dressed
in far LEFT G-Bracket clip!
OPERATION PROCESS
2
1
Dress BOTH H4/Speaker Cables in plastic
clips on G-Bracket.
NOTE: Speaker cables are NOT dressed inside
far left clip on G-Bracket.
clips on G-Bracket.
NOTE: Speaker cables are NOT dressed inside
far left clip on G-Bracket.
28
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
H4 BOARD AND RIGHT SPEAKER (CONTINUED)
1. Wire Dress Right Speaker wires and H4
cables in side clamps (white) and G3-Bd
bracket clips (black).
bracket clips (black).
NOTE: H4-Bd/Rt. Speaker cables are
dressed UNDER AC Inlet.
dressed UNDER AC Inlet.
2. Dress AC Inlet cables as shown.
Make sure Green/Yellow Earth Gnd. Is
screwed into lower LCD Bracket
(w/4x8mm screw)
screwed into lower LCD Bracket
(w/4x8mm screw)
OPERATION PROCESS
NOTE: H4-Bd/Right Speaker cables
ARE dressed in plastic clip.
Clip NOT Eliminated!
ARE dressed in plastic clip.
Clip NOT Eliminated!
2
1
CAUTION:
DO NOT Push hard on AC
inlet wires after routing inside G1 bracket!!
Wire Insulation can be CUT by plastic edges!
Wire Insulation can be CUT by plastic edges!
NOTE:
Running Change will be implemented later.
(PCN/ECN to add M3 clamp).
(PCN/ECN to add M3 clamp).
NOTE Angle of Earth Gnd. Wire.
(Ring terminal touches "dimple" on plate)
(Ring terminal touches "dimple" on plate)
NOTE BOTH H4-Bd and Rt. Speaker
cables are dressed UNDER AC Inlet
cables are dressed UNDER AC Inlet
H4 and Speaker cables are NOT dressed
in small clips! Too difficult to dress with
gloves on operator's hands.
in small clips! Too difficult to dress with
gloves on operator's hands.
Click on the first or last page to see other KDL-32XBR4 / KDL-40D3000 service manuals if exist.