Sony KDL-32XBR4 / KDL-40D3000 Service Manual ▷ View online
13
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
1-3. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL
(KDL-32XBR4 ONLY)
1-4. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL
(KDL-40D3000 ONLY)
1 Remove 2 screws from bottom of Arms, +PSW M5X16
2 Remove 3 screws from bottom bracket and Stand,
2 Remove 3 screws from bottom bracket and Stand,
+PSW M5X16
1 Remove 4 screws from bottom of Arms, +PSW M5X16
2 Remove 4 screws from bottom bracket and Stand, +PSW
2 Remove 4 screws from bottom bracket and Stand, +PSW
M5X16
1
VESA Arm Assembly
Under Cover
Stand Assembly
2
Bottom Bracket
1
VESA Arm Assembly
Under Cover
Stand Assembly
2
Bottom Bracket
14
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
1-5. U2 BOARD, DTT SHIELD, AND JACK HOLDER REMOVAL
1-6. BU2 BOARD REMOVAL
1 Disconnect two connectors
2 Remove three screws, +BVTP 3X12 TYPE2 IT-3
3 Release hooks and remove U2 Board
4 Remove Jack holder from Bezel.
5 Release hooks to remove DTT Shield from BU2 bottom shield.
2 Remove three screws, +BVTP 3X12 TYPE2 IT-3
3 Release hooks and remove U2 Board
4 Remove Jack holder from Bezel.
5 Release hooks to remove DTT Shield from BU2 bottom shield.
1 Remove 2 screws, +PSW M3X5
2 Remove 2 screws, HEX
3 Disconnect 8 connectors
4 Remove 7 screws, +BVST 3X8
5 Remove 5 screws, +PSW M3X5
2 Remove 2 screws, HEX
3 Disconnect 8 connectors
4 Remove 7 screws, +BVST 3X8
5 Remove 5 screws, +PSW M3X5
DTT Shield
1
2
4
5
3
Side Jack Holder
U2 Board
1
2
4
3
5
DTT Top Shield
BU2 Board
DTT Bottom Shield
15
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
1-7. SPEAKER, H3 BOARD, AND H4 BOARD REMOVAL
1-8. G1H BOARD (POWER UNIT) REMOVAL (KDL-32XBR4 ONLY)
1 Remove 4 screws, +PSW 3SG
2 Disconnect 3 connectors
2 Disconnect 3 connectors
1
2
Power Unit
G1 Bracket
Speaker
Baffle
H4 Board
Light
Guide
Guide
H3 Board
LED Guide
3
2
1
4
5
1 Slide out Speaker and Baffl e from Bezel
2 Disconnect one connector from H3 Board
3 Remove 2 screws, (B) (+)PWH Tapping
4 Disconnect one connector from H4 Board
5 Remove 2 screws, (B) (+)PWH Tapping
2 Disconnect one connector from H3 Board
3 Remove 2 screws, (B) (+)PWH Tapping
4 Disconnect one connector from H4 Board
5 Remove 2 screws, (B) (+)PWH Tapping
16
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
1-9. D1 BOARD AND G3 BOARD (POWER UNIT) REMOVAL (KDL-40D3000 ONLY)
1 Disconnect 5 connectors
2 Remove 4 screws, +PSW 3SG
3 Disconnect 4 connectors
4 Remove 4 screws, +PSW 3SG
2 Remove 4 screws, +PSW 3SG
3 Disconnect 4 connectors
4 Remove 4 screws, +PSW 3SG
1-9-1. REPLACING THE INVERTER CONNECTOR ASSEMBLY (KDL-40D3000 ONLY)
1
After inserting the connector
into the Inverter board,
push the middle section
of the inverter connector to
lock on the terminal.
into the Inverter board,
push the middle section
of the inverter connector to
lock on the terminal.
Push the right section of
the inverter connector and
confirm it is securely
connected.
the inverter connector and
confirm it is securely
connected.
Push the left section of
the inverter connector and
confirm it is securely
connected.
the inverter connector and
confirm it is securely
connected.
2
3
Use the following procedure to confirm that the connector is securely attached to the In
4
1
3
2
D1 Board
G3 Board
G3 Bracket
Click on the first or last page to see other KDL-32XBR4 / KDL-40D3000 service manuals if exist.