Sony KDL-32XBR4 / KDL-40D3000 Service Manual ▷ View online
33
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
SPEAKER HARNESS (CONTINUED)
Wire Dress Speaker Cables as shown.
Use UL Tape to align Cables in clip.
BOTH R/L cables are dressed in FGC-3
Use UL Tape to align Cables in clip.
BOTH R/L cables are dressed in FGC-3
conductive clip.
Apply LCD TAPE to BOTH H4-Bd AND Right
speaker Wires.
Apply LCD TAPE to BOTH H4-Bd AND Right
speaker Wires.
TORQUE: 6kg.cm (+-1.0kg.cm)
OPERATION PROCESS
TORQUE SPECIFICATION
1
NO FGC-3 Conductive Clamp/3x8mm screw!
ELIMINATED.
ELIMINATED.
Dress Speaker Wires below level of
LVDS and Under Cover Bracket.
(Pinch Point if cable is too high)
Speaker cable is NOT dressed in the
white clamp (Only left speaker cable is
dressed in white clamp).
LVDS and Under Cover Bracket.
(Pinch Point if cable is too high)
Speaker cable is NOT dressed in the
white clamp (Only left speaker cable is
dressed in white clamp).
LVDS Wire and Speaker Wire cannot touch.
(NG for EMI).
(NG for EMI).
Route Wires Away from metal Tab
(sharp edge)
(sharp edge)
34
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
LEFT SPEAKER HARNESS
1. Dress LEFT speaker harness as shown
OPERATION PROCESS
1
Dress Lt. Speaker wires in Sheet Core C.
Route Wires on TOP of Panel Edge away
from sharp edge.
Route Wires on TOP of Panel Edge away
from sharp edge.
Lt. Speaker cables should only cross
over top of Panel edge once in this
location.
over top of Panel edge once in this
location.
35
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
U2 BOARD
1. Apply TAPE, U2 to Panel in location
where U2 bracket is to be installed
(Use edges of panel as guide)
(Use edges of panel as guide)
2. Make sure DTT Shield has Sheet Core C
installed as per diagram.
3. Wire Dress 20P Harness as shown.
Put attention on DIRECTION of wires from
BU2-Bd inside side clamp on U2 Bracket.
BU2-Bd inside side clamp on U2 Bracket.
OPERATION PROCESS
2
1
Align side edge of panel
Align with bottom of panel
Sheet Core C (Installed by Vendor)
3
3/4/2007 LATE CHANGE:
ADD 3x12mm SCREW Here.
ADD 3x12mm SCREW Here.
DO NOT Cross wires over
Optical Output Connector
(Pinch Point when Rr. Cover is
installed).
Optical Output Connector
(Pinch Point when Rr. Cover is
installed).
36
KDL-32XBR4/40D3000
KDL-32XBR4/40D3000
KDL-32XBR4 ONLY
H1 BOARD
1. Dress/Route H1-Bd harness as shown
on photo.
2. NOTE: Put attention on SLACK of cable.
Between Connector on H1 and tape there
is slack in wire.
Between tape/clamp there is slack.
Between tape/DTT Shield there is slack.
is slack in wire.
Between tape/clamp there is slack.
Between tape/DTT Shield there is slack.
OPERATION PROCESS
1
2
NOTE which connector
cables are attached to
on H1-Bd.
cables are attached to
on H1-Bd.
Plastic Side Clamp.
Installed by Vendor.
Installed by Vendor.
2
Click on the first or last page to see other KDL-32XBR4 / KDL-40D3000 service manuals if exist.