Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man4) Service Manual ▷ View online
6-28
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
10. CAMERA Adjustment 6
Note:
Note:
“CAMERA Adjustment 6” is available only once after the
power is turned on. If the adjustment is retried, turn off the
power and turn on again.
power is turned on. If the adjustment is retried, turn off the
power and turn on again.
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Strobe Light Level Adj.
3. Strobe White Balance Adj.
4. Release of Data Setting during Camera Adj.
sequence]
1. Data Setting during Camera Adj.
2. Strobe Light Level Adj.
3. Strobe White Balance Adj.
4. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 6.
2) The Automatic Adjustment Program executes “1. Data Setting
1) Click the [Start] button of the CAMERA Adjustment 6.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “4. Preparing the Flash
Adjustment Box” (see page 6-6).)
ject in accordance with the message.
(For the Flash adjustment box, refer to “4. Preparing the Flash
Adjustment Box” (see page 6-6).)
4) Press the [OK] button, and the items “2. Strobe Light Level
Adj.” and “3. Strobe White Balance Adj.” will be executed.
5) Upon completion of “3. Strobe White Balance Adj.”, “4. Re-
lease of Data Setting during Camera Adj.” is executed
6) Upon successful completion of all items of the CAMERA Ad-
justment 6, the following message is displayed. Click the [OK]
button.
button.
11. CAMERA Adjustment 7
(HDR-SR5/SR5C/SR5E only)
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Steady Shot Check
3. Release of Data Setting during Camera Adj.
sequence]
1. Data Setting during Camera Adj.
2. Steady Shot Check
3. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 7.
2) The Automatic Adjustment Program executes “1. Data Setting
1) Click the [Start] button of the CAMERA Adjustment 7.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed.
With the camcoder in stationary state, click the [OK] button.
With the camcoder in stationary state, click the [OK] button.
4) If the [OK] button is clicked, “2. Steady Shot Check” is ex-
ecuted.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.
5) If the [OK] button is clicked, “3. Release of Data Setting dur-
ing Camera Adj.” is executed.
6) Upon successful completion of all items of the CAMERA
Adjustment 7, the following message is displayed. Click the
[OK] button.
[OK] button.
6-29
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
1
2
3
4
1
2
3
4
SE7202
SE7201
CM-077 BOARD (SIDE A)
PP
YY
YY: YAW sensor
sensitivity S
sensitivity S
7201
PP: PITCH sensor sensitivity S
7202
Preparation:
1) Read the PITCH sensor (CM-077 board SE7202) sensitivity
1) Read the PITCH sensor (CM-077 board SE7202) sensitivity
written on repair parts, and named this as S
7202
.
2) Read the YAW sensor (CM-077 board SE7201) sensitivity writ-
ten on repair parts, and named this as S
7201
.
Fig. 6-1-19
How to read the sensitivity data of angular velocity sen-
sor
sor
With the pins 1 and 2 of angular velocity sensor placed in the
lower position, read the data value.
lower position, read the data value.
Description example:
For the sensor sensitivity value 60
Fig. 6-1-20
12. CAMERA Adjustment 8
(HDR-SR7/SR7E/SR8/SR8E only)
Perform this adjustment only when replacing the GYRO sensor or
lens block. When the microprocessor, circuit etc. is damaged, don't
perform this adjustment but check the operations only.
lens block. When the microprocessor, circuit etc. is damaged, don't
perform this adjustment but check the operations only.
12-1. Preparation when the GYRO sensor or the CM-
077 board is replaced
Note down the sensitivity displayed on the GYRO sensor of the re-
pair parts. At this time, note down also to which board it was attached
to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.
pair parts. At this time, note down also to which board it was attached
to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.
Precautions on the Parts Replacement
The PITCH sensor and the YAW sensor are different parts.
Precautions on GYRO Sensor
The sensor incorporates a precision oscillator. Handle it with care as
if it dropped, the balance of oscillator will be disrupted and opera-
tions will not be performed properly.
if it dropped, the balance of oscillator will be disrupted and opera-
tions will not be performed properly.
Adjustment Block
11
Adjustment Page
80
Adjustment Address
7F12, 7F13
Note:
The sensor sensitivity of SE7201 and SE7202 of the CM-
077 board is written only repair parts.
077 board is written only repair parts.
6 0
Hand Writing
1
2
4
3
6-30
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
12-3. GYRO Sensor Sensitivity Adjustment
[Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-
1) Click the [Start] button of Camera Adjustment 8, and the fol-
lowing screen will appear.
2) Input the sensitivity of respective sensors (S
7201
, S
7202
) read at
“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.
3) Input the PITCH/YAW data of lens (L
1
, L
2
) read at “Prepara-
tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
4) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.
sult is written to the memory in the camera.
5) Upon successful completion of the data writing, the following
screen will appear. Check that the steady shot function oper-
ates normally.
ates normally.
12-2. Preparation when the lens is replaced
Note down the PITCH/YAW data on the replacement lens for repair.
Adjustment Block
11
Adjustment Page
80
Adjustment Address
7F12, 7F13
Note:
The PITCH/YAW data of lens is written only repair parts.
Preparation:
1) Read the PITCH data written on repair parts, and named this
1) Read the PITCH data written on repair parts, and named this
as L
1
.
2) Read the YAW data written on repair parts, and named this as
L
2
.
Fig. 6-1-21
YAW data
t
L
2
PITCH/YAW Data
PITCH data
t
L
1
X.XX / X.XX
6-31
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
1-8.
LCD/EVF SYSTEM ADJUSTMENTS
1.
Function of Each Button on LCD/EVF System
Adjustment Screen
Adjustment Screen
Click the [LCD/EVF SYSTEM ADJUSTMENT] button on the Main
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-22 will appear.
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-22 will appear.
Fig. 6-1-22
Table 6-1-5
1
[To Menu] button
The Main Menu screen comes back.
The Main Menu screen comes back.
2
[Start] button
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
3
[Release Data Setting] button
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD/EVF ad-
justment. If the adjustment completed successfully, the data
setting is automatically cancelled and the button color returns
to “white”.)
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD/EVF ad-
justment. If the adjustment completed successfully, the data
setting is automatically cancelled and the button color returns
to “white”.)
2.
Adjustment Items of LCD/EVF System Adjustment
The adjustment items of LCD/EVF system adjustment are as listed
in Table 6-1-5. The Automatic Adjustment Program executes the
adjustment items if the LCD/EVF Adjustment Start button is
clicked.
in Table 6-1-5. The Automatic Adjustment Program executes the
adjustment items if the LCD/EVF Adjustment Start button is
clicked.
3
2
1
Block
Page
Address
VCO Adj.
10
60
1050 (NTSC model),
1051 (PAL model)
1051 (PAL model)
Contrast Adj.
10
60
1058
V-COM Adj.
10
60
1052
Transmissive Mode White Balance Adj.
10
60
1056, 1057
Reflective Mode White Balance Adj.
10
60
107B, 107C
Sample Hold Phase Adj.
10
60
105F
VCO Adj.
10
60
103F (NTSC model),
1040 (PAL model)
1040 (PAL model)
Contrast Adj.
10
60
1047
White Balance Adj.
10
60
1045, 1046
Touch Panel
Adjustment
Adjustment
Touch Panel Adj.
Adjusting Address
(Note 1)
Button Name
Adjustment
EVF
Adjustment
(Note 2)
Adjustment
(Note 2)
LCD
Adjustment
Adjustment
Note 1:
The adjustment data cannot be read or written from the SeusEX.
Note 2:
HDR-SR7/SR7E/SR8/SR8E only
Click on the first or last page to see other HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man4) service manuals if exist.