DOWNLOAD Sony HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man4) Service Manual ↓ Size: 1005.39 KB | Pages: 91 in PDF or view online for FREE

6-55

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Precautions on the Parts Replacement
There are two types of repair parts.

Type A

ECN-03MA

Type B

ECN-03MB

Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations.

Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.

Subject

Not required

Measurement Point

Displayed data of page: 1 (Note 1)

Measuring Instrument

Adjusting remote commander

Specified value

PITCH data: 2680 to 5080
YAW data: 2680 to 5080

Note 1: The right four digits of the page: 1 displayed data of the

adjusting remote commander.

1 : XX : XX

Displayed data

Note 2: Check that the data of page: 0, address: 10 is “00”.

Switch setting
1) ZOOM ..................................................................... TELE end
2) STEADY SHOT (Menu setting) ....................................... ON

Order Page Address Data

Procedure

  PITCH sensor output check (SE6802 of EE-001 board)

1

0

03

11

2

1

With the set in still state,
check that the displayed data
(Note 1) satisfies the PITCH
data specified value.

  YAW sensor output check (SE6801 of EE-001 board)

3

0

03

12

4

1

With the set in still state,
check that the displayed data
(Note 1) satisfies the YAW
data specified value.

5

0

03

00

  Steady shot operation check

6

Shake the set vertically and
horizontally to check that the
steady shot function operates
normally.

6-56

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

1

16

LANC jack

Adjustment remote 
commander (RM-95)

AC IN

DC IN jack

AC adaptor

1

TT-001 board

NN-001 board

CN7005

16

CPC-7 jig
(J-6082-382-A)

Before perform the viewfinder system adjustments, check the data
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.

Note 1: Taken an extreme care not to destroy the liquid crystal

display module by static electricity when replacing it.

Note 2: Perform the following data setting before the viewfinder

system adjustments.

1) Select page: 3, address: C4, and set data: 67.
2) Select page: 3, address: C5, and set data: 01.

Reset the data after completing adjustment.

1) Select page: 3, address: C4, and set data: 00.
2) Select page: 3, address: C5, and set data: 00.

Switch setting
1) REC FORMAT (Menu setting) ............................ HDV 1080i

[Adjusting connector]
Most of the measuring points for adjusting the viewfinder system
are concentrated in CN7005 of the NN-001 board.
Connect the Measuring Instruments via the CPC-7 jig (J-6082-
382-A).
The following table shown the Pin No. and signal name of CN7005.

Pin No. Signal Name

Pin No. Signal Name

1

EVF_COM_DC

9

RF_MON

2

REG_GND

10

REG_GND

3

EXT_DA

11

SWP

4

EVF_VCO

12

FRRV

5

EVF_VG

13

REC_CRRT1

6

PSIG

14

REC_CRRT0

7

REG_GND

15

NC

8

REG_GND

16

NC

6-57

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Set the VCO free-run frequency. If deviated, the EVF screen will
be blurred.

Mode

CAMERA

Subject

Not required

Measurement Point

Pin 4 of CN7005 (EVF_VCO) on
NN-001 board

Measuring Instrument

Frequency counter

Adjustment Page

C

Adjustment Address

34, 35

Specified Value

f = 15734 

± 30 Hz (NTSC)

f = 15625 

± 30 Hz (PAL)

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Refer to table 6-4-1. “Hexadecimal-decimal conversion

table”

Note 3: If D

35

’ > 255, then D

35

 = FF (NTSC model)

If D

34

’ < 0, then D

34

 = 00 (PAL model)

Order Page Address Data

Procedure

1

0

01

01

2

C

34

Change the data and set the
frequency (f) to the specified
value.

3

C

34

Press PAUSE button.

4

C

34

Read the data and this data is
named D

34

.

5

Convert D

34

 to decimal

notation, and obtain D

34

’.

(Note 3)

6

Calculate D

35

’ using

following equations.
(decimal calculation)
D

35

’ = D

34

’ + 21

7

Convert D

35

’ to a hexadeci-

mal number, and obtain D

35

.

(Note 3, 4)

8

C

35

D

35

Press PAUSE button.

9

0

01

00

Order Page Address Data

Procedure

1

0

01

01

2

C

35

Change the data and set the
frequency (f) to the specified
value.

3

C

35

Press PAUSE button.

4

C

35

Read the data and this data is
named D

35

.

5

Convert D

35

 to decimal

notation, and obtain D

35

’.

(Note 3)

6

Calculate D

34

’ using

following equations.
(decimal calculation)
D

34

’ = D

35

’ – 21

7

Convert D

34

’ to a hexadeci-

mal number, and obtain D

34

.

(Note 3, 4)

8

C

34

D

34

Press PAUSE button.

9

0

01

00

6-58

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Set the uniformity improvement signal level to an appropriate level.

Mode

CAMERA

Subject

Not required

Measurement Point

Pin 6 of CN7005 (PSIG) on NN-
001 board

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

39

Specified Value

A = 6.00 

± 0.05 Vp-p

Note: Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

C

39

Change the data and set the
PSIG signal level (A) to the
specified value.
(The data should be “00” to
“7F”.)

3

C

39

Press PAUSE button.

4

0

01

00

A

2H

Set the back light luminance.
If deviated, the image may become dark or bright.

Mode

CAMERA

Subject

Not required

Measurement Point

Pin 3 of CN7005 (EXT_DA) on
NN-001 board

Measuring Instrument

Digital voltmeter

Adjustment Page

C

Adjustment Address

32, 33

Specified Value

NORMAL mode:

A = 1.00 

± 0.05 Vdc

BRIGHT mode:

B = 1.65 

± 0.05 Vdc

Note: Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

C

32

Change the data and set the
DC voltage (A) to the
specified value of NORMAL
mode.

3

C

32

Press PAUSE button.

4

C

33

Change the data and set the
DC voltage (B) to the
specified value of BRIGHT
mode.

5

C

33

Press PAUSE button.

6

0

01

00