DOWNLOAD Sony HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man4) Service Manual ↓ Size: 1005.39 KB | Pages: 91 in PDF or view online for FREE

6-63

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Correct the white balance at reflective mode.
If deviated, the LCD screen color cannot be reproduced.

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Adjustment Page

C

Adjustment Address

70, 71

Note 1: Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

3

C4

59

3

3

C5

02

4

3

0C

20

Press PAUSE button.

5

3

22

0F

Press PAUSE button.

6

3

01

66

Press PAUSE button. (Note 2)

7

3

02

Check the data changes to
“00”.

8

3

03

Check the data is “02”. (Note 4)

9

3

03

00

10

3

01

67

Press PAUSE button. (Note 3)

11

3

02

Check the data changes to
“00”.

12

3

03

Check the data is “02”. (Note 4)

13

3

03

00

14

3

C4

00

15

3

C5

00

16

3

0C

00

Press PAUSE button.

17

3

22

00

Press PAUSE button.

18

0

01

00

Note 2: The adjustment data will be automatically input to page:

C, address: 70.

Note 3: The adjustment data will be automatically input to page:

C, address: 71.

Note 4: If the data is “01”, adjustment has error.

Adjust the calibration of touch panel.

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Adjustment Page

A

Adjustment Address

90 to 93

Note 1: This adjustment should be carried out upon completetion

of “LCD Automatic Adjustment”.

Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that a Memory Stick Duo is not insteted.
Note 4: Check that the LCD panel is not reverse mode.
Note 5: Adjustment must be performed while observing the LCD

screen from the front.

Order Page Address Data

Procedure

1

5

01

01

2

5

05

00

3

5

06

A2

4

5

07

00

5

5

08

00

6

5

09

00

7

5

0A

FF

8

5

0B

00

9

5

0C

00

10

5

0D

00

11

5

0E

01

12

5

00

01

Press PAUSE button.

13

Check that the touch panel
adjustment screen is
displayed.

14

Perform “Adjusting method”.

Adjusting method:
1) Using a ball-point pen etc., push the center of “

” indicated

in the part A.

2) Using a ball-point pen etc., push the center of “

” indicated

in the part B.

3) Using a ball-point pen etc., push the center of “

” indicated

in the part C.

A

C

B

6-64

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

On the mechanism section adjustment
For details of mechanism section adjustments, checks, and replace-
ment of mechanism parts, refer to the separate volume “DV ME-
CHANICAL ADJUSTMENT MANUAL IX  N Mechanism  ”.

1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander

to the ON position.

3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0C, and press the PAUSE

button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)
Note: The function buttons become inoperable.

5) To quit the record mode, select page: 3, address: 01, set data:

00, and press the PAUSE button of the adjustment remote com-
mander.  (Whenever you want to quit the record mode, be sure
to quit following this procedure.)

1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander

to the ON position.

3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0B, and press the PAUSE

button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)
Note: The function buttons become inoperable.

5) To quit the playback mode, select page: 3, address: 01, set

data: 00, and press the PAUSE button of the adjustment re-
mote commander.  (Whenever you want to quit the playback
mode, be sure to quit following this procedure.)

1) Clean the tape running side (tape guide, drum, capstan shaft,

pinch roller, etc.).

2) Connect the adjustment remote commander to the LANC jack.
3) Turn the HOLD switch of the adjustment remote commander

to the ON position.

4) Connect an oscilloscope to NN-001 board CN7005 via the

CPC-7 jig (J-6082-382-A).

Channel 1: NN-001 board, CN7005 Pin 9 (Note)
External trigger: NN-001 board, CN7005 Pin qa

Note: Connect a 75 

Ω resistor between pins 9 of CN7005

and 8 (GND).
75 

Ω resistor (Parts code: 1-247-804-11)

5) Playback the alignment tape for tracking. (XH2-1)
6) Select page: 3, address: 33, and set data: 08.
7) Select page: 3, address: 26, set data: 31, and press the PAUSE

button.

8) Check that the oscilloscope RF waveform is normal at the en-

trance and exit.
If not normal, adjust according to the separate volume
“DV MECHANICAL ADJUSTMENT MANUAL IX
N Mechanism  ” .

1) Connect the adjustment remote commander to the LANC jack

and set the HOLD switch to the ON position.

2) Select page: 3, address: 26, set data: 00, and press the PAUSE

button.

3) Select page: 3, address: 33, and set data: 00.

Pin No. Signal Name

Pin No. Signal Name

1

EVF_COM_DC

9

RF_MON

2

REG_GND

10

REG_GND

3

EXT_DA

11

SWP

4

EVF_VCO

12

FRRV

5

EVF_VG

13

REC_CRRT1

6

PSIG

14

REC_CRRT0

7

REG_GND

15

NC

8

REG_GND

16

NC

CH1

Entrance side

Exit side

Check this section

(Normal waveform)

CH2

(Trigger)

3.3msec

6-65

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Note: Before performing the adjustment, check the data of page:

0, address: 10 is “00”. If not, select page: 0, address: 00,
and set data “00”.

1) The adjustments of this unit are performed in the VTR mode

(PLAY/EDIT mode) or camera mode (CAMERA-TAPE
mode).

The measuring point of the playback RF signal is CN7005 of NN-
001 board. Connect the measuring instruments via the CPC-7 jig
(J-6082-382-A). Refer to “MECHANISM SECTION ADJUST-
MENT” for the measuring method. The following table lists the
pin numbers and signal names of CN7005.

Pin No. Signal Name

Pin No. Signal Name

1

EVF_COM_DC

9

RF_MON

2

REG_GND

10

REG_GND

3

EXT_DA

11

SWP

4

EVF_VCO

12

FRRV

5

EVF_VG

13

REC_CRRT1

6

PSIG

14

REC_CRRT0

7

REG_GND

15

NC

8

REG_GND

16

NC

Connect the measuring instruments as shown in Fig. 6-3-1, and
perform the adjustments.

1

16

Osilloscope

Terminated
75 

Ω

Osilloscope

Terminated
75 

Ω

LANC jack

A/V jack

Audio L (White)

Audio R (Red)

Video

 (Yellow)

S Video

 (Black)

COMPONENT 
OUT jack

Pr (Red)

Pb (Blue)

Y (Green)

Adjustment remote 
commander (RM-95)

AC IN

DC IN jack

AC adaptor

1

TT-001 board

NN-001 board

CN7005

16

CPC-7 jig
(J-6082-382-A)

VIDEO system adjustment (COMPONENT OUT)

VIDEO system adjustment (S VIDEO, VIDEO)

6-66

HDR-HC1/HC1E/HC1K/HC1EK_ADJ

Use the alignment tapes shown in the following table.
Use tapes specified in the signal column of each adjustment.

Fig. 6-3-2 shows the 75% color bar signals recorded on the align-
ment tape for Audio Operation Check.

Note: Measure with video terminal (Terminated at 75 

Ω)

      Name

Tracking standard (XH2-1)

SW/OL standard (XH2-3)

Audio operation check
(XH5-3 (NTSC), XH5-3P (PAL))

System operation check
(XH5-5 (NTSC), XH5-5P (PAL))

Use

Tape path adjustment

Switching position adjust-
ment

Audio system adjustment

Operation check

Color bar signal waveform

Color bar pattern

Color bar signal waveform

Color bar pattern

Video output

A/V jack
Video signal:

1 Vp-p, 75 

Ω unbalanced,

sync negative

S video output

A/V jack
Luminance signal:

1 Vp-p, 75 

Ω unbalanced,

sync negative

Chrominance signal: 0.286 Vp-p, 75

Ω unbalanced (NTSC)

: 0.300 Vp-p, 75

Ω unbalanced (PAL)

Audio output

A/V jack

Output level: 327mV (at load impedance 47 k

Ω)

Output impedance: Below 2.2 k

Ω

1 V

0.714 V

0.286 V

White (75%)

White (100%)

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

0.286 V

Q

I

Horizontal sync signal

(75%)

White

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Q

I

White

(100%)

Black

1 V

0.7 V

0.3 V

White (100%)

Ye

llo

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

Horizontal sync signal

0.3 V

(100%)

Ye

llo

w

Cy

an

Green

Magenta

Red

Blue

White

Blac

k