Sony HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man4) Service Manual ▷ View online
6-79
HDR-HC1/HC1E/HC1K/HC1EK_ADJ
2-3.
Emergence Memory Address (Mechanism
section)
section)
Page C
Address F4 to FF
Address
Contents
F4
EMG code when first error occurs
F6
Upper: MSW code when shift starts when first error
occurs
Lower: MSW code when first error occurs
F7
Lower: MSW code to be moved when first error
occurs
F8
EMG code when second error occurs
FA
Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs
FB
Lower: MSW code to be moved when second error
occurs
FC
EMG code when last error occurs
FE
Upper: MSW code when shift starts when last error
occurs
Lower: MSW code when last error occurs
FF
Lower: MSW code to be moved when last error
occurs
When no error occurs in this unit, data “00” is written in the above
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (F4 to F7). In the same way, when the second error occurs,
the data corresponding to the error is written in the second emer-
gency address (F8 to FB).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (FC to FF).
Note: After completing adjustments, be sure to initialize the data
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (F4 to F7). In the same way, when the second error occurs,
the data corresponding to the error is written in the second emer-
gency address (F8 to FB).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (FC to FF).
Note: After completing adjustments, be sure to initialize the data
of addresses F4 to FF to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
3
01
37
Press PAUSE button.
3
3
02
Check the data changes to
“00”.
“00”.
4
0
01
00
2-4.
EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in C
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
Code
Emergency Type
00
No error
10
Loading motor emergency during loading
11
Loading motor emergency during unloading
22
T reel emergency during normal rotation
23
S reel emergency during normal rotation
24
T reel emergency (Short circuit between S reel
terminal and T reel terminal)
terminal and T reel terminal)
30
FG emergency at the start up of the capstan
40
FG emergency at the start up of the drum
42
FG emergency during normal rotation of the drum
6-80
HDR-HC1/HC1E/HC1K/HC1EK_ADJ
Ver. 1.2 2007.09
Position
EJ
BL
ULE
LD1 (SR)
LD2 (HL)
STOP
R/P
NULL
Code
2
7
3
1
5
4
6
0
F
Contents
Position at which the cassette component lock is released, at the farthest unload side mechanically
at which the mechanism can move no further in the UNLOAD direction.
at which the mechanism can move no further in the UNLOAD direction.
BLANK code, at the boundary between codes.
EJECT completion position. when the cassette is ejected, the mechanism will stop at this position.
Cassette IN standby. The guide will start protruding out as the mechanism moves towards the
LOAD position.
Cassette IN standby. The guide will start protruding out as the mechanism moves towards the
LOAD position.
When prepraing TOP load processing or when DEW is detected, rolling up tape by T reel is
preformed at this position.
preformed at this position.
When prepraing TOP load processing or when DEW is detected, rolling up tape by S reel is
preformed at this position.
preformed at this position.
Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the
brake is imposed on both reels.
brake is imposed on both reels.
PB, REC, CUE, REVIEW, PAUSE, FF, REW positions. When pinch roller is pressed, and the
tension regulator is ON, the mechanism is operating at this position in modes in which normal
images are shown.
tension regulator is ON, the mechanism is operating at this position in modes in which normal
images are shown.
Code not existing in the MD. Default value.
Status before finding any mechanism position.
2-5.
MSW Code
MSW when errors occur:
Information on MSW (mode SW) when errors occur
MSW when movement starts:
Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)
MSW of target of movement:
Information on target MSW of movement when the mechanism position is moved
Information on MSW (mode SW) when errors occur
MSW when movement starts:
Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)
MSW of target of movement:
Information on target MSW of movement when the mechanism position is moved
0010=2
0111=7
← UNLOAD
Lock released
Cassette compartment
Cassette compartment
Pinch roller pressing
LS chassis movement section
EJ
BL
0011=3
0111=7
ULE
BL
0001=1
0111=7
LD1 (SR)
LD2 (HL)
BL
0101=5
0111=7
BL
0100=4
0111=7
STOP
BL
0110=6
R/P
LOAD
→
← D (MSB)
← C
← B
← A (LSB)
← C
← B
← A (LSB)
Mechanical Position
6-81
HDR-HC1/HC1E/HC1K/HC1EK_ADJ
3.
Bit Value Discrimination
Bit values must be discriminated using the display data of the ad-
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
(Example) If the remote commander display is “8E”, bit value from
bit 7 to bit 4 can be discriminated from the column A,
and those from bit 3 to bit 0 from column B.
and those from bit 3 to bit 0 from column B.
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
Display on the
adjustment
remote
commander
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
C
)
D (
d
)
E (
E
)
F (
F
)
Bit values
bit3
or
bit7
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2
or
bit6
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1
or
bit5
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0
or
bit4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
A
B
4.
Jack Check (1)
Page 7
Address F9
Using method:
1) Select page: 7, address: F9.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: F9.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
5.
Jack Check (2)
Page 7
Address F3
Using method:
1) Select page: 7, address: F3.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: F3.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
6.
Jack Check (3)
Page 7
Address F4
Using method:
1) Select page: 7, address: F4.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: F4.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
Bit
Function
When bit value = 1
When bit value = 0
0
COMPONENT OUT jack (HH-001 board CN105)
Used
Not used
Bit
Function
When bit value = 1
When bit value = 0
0
A/V OUT jack (HH-001 board CN106)
Used
Not used
Bit
Function
When bit value = 1
When bit value = 0
2
COMPONENT OUT jack (HH-001 board CN105)
Used
Not used
3
MIC jack (FP-245 flexible J8501)
Mono
Stereo
6-82
HDR-HC1/HC1E/HC1K/HC1EK_ADJ
7.
Switch Check (2)
Page 7
Address F4
Using method:
1) Select page: 7, address: F4.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
1) Select page: 7, address: F4.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
Bit
Function
When bit value = 1
When bit value = 0
4
REC PROOF SW (Mechanism chassis)
SAVE
REC
Bit
Function
When bit value = 1
When bit value = 0
0
POWER (PS12300 block)
ON
OFF
1
MODE CHANGE (PS12300 block)
ON
OFF
3
EJECT (FP-263 flexible S002)
ON
OFF
4
CC DOWN (Mechanism chassis)
ON (DOWN)
OFF (UP)
5
DISP/BATT INFO (RR-001 board S9002)
ON
OFF
7.
Switch Check (1)
Page 2
Address 81
Using method:
1) Select page: 2, address: 81.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
1) Select page: 2, address: 81.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
Click on the first or last page to see other HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man4) service manuals if exist.