DOWNLOAD Sony DCR-TRV10 / DCR-TRV10E / DCR-TRV8 / DCR-TRV8E (serv.man2) Service Manual ↓ Size: 35.38 MB | Pages: 127 in PDF or view online for FREE

5-27

R-Y

2mm

B-Y

2mm

R-Y

B-Y

1.5mm

3mm

3mm

R-Y

B-Y 

3mm

3mm

3.5mm

1.5mm

Fig. 5-1-12. (A)

Fig. 5-1-12. (B)

Fig. 5-1-12. (C)

Subject

Clear chart (Color reproduction
adjustment frame)

Filter

Filter C14 for color temperature
correction
ND filter 1.0 and 0.4 and 0.1

Measurement Point

Video output terminal

Measuring Instrument

Vectorscope

Specified Value

Fig. 5-1-12. A to C

Switch setting:
1)

NIGHT SHOT .................................................................. OFF

Checking method:
1)

Check that the lens is not covered with either filter.

2)

Select page: 6, address: 01, set data: 0F, and press the PAUSE
button of the adjustment remote commander.

3)

Check that the center of the white luminance point is within
the circle shown Fig. 5-1-12. (A).

4)

Select page: 6, address: 01, set data: 23, and press the PAUSE
button.

5)

Place the C14 filter on the lens.

6)

Check that the center of the white luminance point settles in
the circle shown Fig. 5-1-12. (B).

7)

Remove the C14 filter, and place the ND filter 1.5 (1.0 + 0.4 +
0.1) on the lens.

8)

Check that the white luminance point stopped moving, and then
remove the ND filter 1.5.

9)

Check that the center of the white luminance point settles within
the circle shown Fig. 5-1-12. (C).

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

• This adjustment is performed only when replacing the angular

velocity sensor.

Although this adjustment need not be performed when the circuit

is damaged, etc., check the operations.

• Note down the sensitivity displayed on the angular velocity sensor

of the repair parts. At this time, note down also to which board it
was attached to.

Be sure to check because if attached incorrectly, the screen will

vibrate up and down or left and right during hand-shake correction
operations.

Precautions on the Parts Replacement
There are two types of repair parts.

Type A: ENC03JA
Type B: ENC03JB

Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations. After replacing, re-
adjust according to the adjusting method after replacement.

Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.

Adjustment Page

F

Adjustment Address

41, 42

The sensor sensitivity of SE451 and SE450 of the JK-170 board is
written only on the repair parts.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Read the sensor sensitivity written on SE451 (PITCH sensor)
of the JK-170 board, and take this as S

451

.

3)

Read the sensor sensitivity written on SE450 (YAW sensor) of
the JK-170 board, and take this as S

450

.

4)

Calculate D

41

’ and D

42

’ using the following equation (decimal

calculation).
NTSC model

D

41

’ = 92 / S

451

D

42

’ = 108 / S

450

PAL model

D

41

’ = 148 / S

451

D

42

’ = 128 / S

450

5)

Convert D

41

’ and D

42

’ into hexadecimal digits, to obtain D

41

and D

42

. (Round off decimal points)

6)

Select page: F, address: 41, set data: D

41

, and press the PAUSE

button of the adjustment remote commander.

7)

Select page: F, address: 42, set data: D

42

, and press the PAUSE

button of the adjustment remote commander.

Processing after Completing Adjustments
1)

Select page: 0, address: 01, and set data: 00.

2)

Check that the steady shot operations have been performed
normally.

5-28

H

A

GND level
(0Vdc)

1

3

5

7

9

11

13

15

17

19

LANC SIG

EVF BL –

EVF VCO

PD VG

H START

PANEL COM

TCK

TDO

SWP

GND

2

4

6

8

10

12

14

16

18

20

EVF BL +

EVF VG

GND

PD VCO

XHD/PSIG

TMS

TDI

GND

RF IN/LANC JACK IN

RF MON

The back light (fluorescent tube) is driven by a high voltage AC
power supply. Therefore, do not touch the back light holder to
avoid electrical shock.

When replacing the LCD unit, be careful to prevent damages
caused by static electricity.

Set the VF BRIGHT (Menu display) to the center.

As the PANEL CLOSE switch (FP-91 flexible board S96) is
attached to the cabinet (R), this cabinet must be attached when
performing adjustments.

Most of the measuring points for adjusting the viewfinder system
are concentrated in CN2904 of the VC-217 board.
Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-A).
The following table shows the Pin No. and signal name of CN2904.

Table 5-1-7.

Set the VCO free-run frequency. If deviated, the EVF screen will be
blurred.

Mode

VTR stop

Signal

Arbitrary

Measurement Point

Pin 5 of CN2904 (EVF VCO) on
VC-217 board

Measuring Instrument

Oscilloscope (DC range)

Adjustment Page

D

Adjustment Address

75

Specified Value

A = 1.7 ± 0.05V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Check the GND level of the oscilloscope.

3)

Select page: D, address: 75, change the data and set the VCO
output voltage (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 0, address: 01, and set data: 00.

Fig. 5-1-13.

Fig. 5-1-14.

CN2904

1

2

19

20

Remove the CPC cover

5-29

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Mode

Camera

Subject

Arbitrary

Measurement Point

Pin 4 of CN2904 (EVF VG) on
VC-217 board

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

7A

Specified Value

A = 7.25 ± 0.05V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 3, address: 0C, set data: 20, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 3, address: 22, set data: 02, and press the PAUSE
button of the adjustment remote commander.

4)

Select page: D, address: 7A, change the data and set the voltage
(A) between the reversed waveform pedestal and non-reversed
waveform pedestal to the specified value.
(The data of address: 7A should be “54” to “D7”.)

5)

Press the PAUSE button of the adjustment remote commander.

6)

Select page: 3, address: 22, set data: 00, and press the PAUSE
button of the adjustment remote commander.

7)

Select page: 3, address: 0C, set data: 00, and press the PAUSE
button of the adjustment remote commander.

8)

Select page: 0, address: 01, and set data: 00.

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Mode

Camera

Subject

Arbitrary

Measurement Point

Pin 4 of CN2904 (EVF VG) on
VC-217 board

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

7B

Specified Value

A = 1.81 ± 0.05V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 3, address: 0C, set data: 20, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 3, address: 22, set data: 02, and press the PAUSE
button of the adjustment remote commander.

4)

Select page: D, address: 7B, change the data and set the voltage
(A) between the 100 IRE and 0 IRE (pedestal) to the specified
value.

5)

Press the PAUSE button of the adjustment remote commander.

6)

Select page: 3, address: 22, set data: 00, and press the PAUSE
button of the adjustment remote commander.

7)

Select page: 3, address: 0C, set data: 00, and press the PAUSE
button of the adjustment remote commander.

8)

Select page: 0, address: 01, and set data: 00.

Pedestal

Pedestal

A

2H

100 IRE

0 IRE (Pedestal)

A

2H

Fig. 5-1-15.

Fig. 5-1-16.

5-30

Set the backlight luminance and color temperature.
If deviated, the image may become dark or bright.

Mode

Camera

Subject

Arbitrary

Measurement Point

+ Probe: Pin 2 of CN2904 (EVF BL +)

on VC-217 board

– Probe: Pin 3 of CN2904 (EVF BL –)

on VC-217 board

Measuring Instrument

Digital voltmeter

Adjustment Page

D

Adjustment Address

76

Specified Value

A = 17.0 ± 1.0mVdc

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 76, change the data and set the voltage
difference (A) between Pin 2 of CN2904 (EVF BL +) and
Pin 3 of CN2904 (EVF BL –) to the specified value.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

Correct the white balance.
If deviated, the reproduction of the EVF screen may degenerate.

Mode

Camera

Subject

Arbitrary

Measurement Point

Check on EVF screen

Measuring Instrument

Adjustment Page

D

Adjustment Address

71, 72

Specified Value

The EVF screen should not be
colored.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 3, address: 0C, set data: 20, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 3, address: 22, set data: 0B, and press the PAUSE
button of the adjustment remote commander.

4)

Select page: D, address: 71 and 72, set the data to the initial
value.

Press the PAUSE button of the adjustment remote commander
each time to set the data.

5)

Check that the EVF screen is not colored. If colored, change
the data of page: D, address: 71 and 72 so that the EVF screen
is not colored.

To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.

6)

Select page: 3, address: 22, set data: 00, and press the PAUSE
button of the adjustment remote commander.

7)

Select page: 3, address: 0C, set data: 00, and press the PAUSE
button of the adjustment remote commander.

8)

Select page: 0, address: 01, and set data: 00.

DCR-TRV10

DCR-TRV8

DCR-TRV10E

DCR-TRV8E

71

8B

99

80

9A

72

6A

5A

62

59