DOWNLOAD Sony DCR-TRV10 / DCR-TRV10E / DCR-TRV8 / DCR-TRV8E (serv.man2) Service Manual ↓ Size: 35.38 MB | Pages: 127 in PDF or view online for FREE

5-19

Before perform the camera system adjustments, check that the
specified value of “VIDEO SYSTEM ADJUSTMENT” are satisfied.

Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.

Subject

Not required

Measurement Point

R285(Pin ^£ of IC207)
or CL200(Pin !™ of IC202)

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

1C

Specified Value

R285 (Pin ^£ of IC207):

f=13500000 ± 68Hz

CL200 (Pin !™ of IC202):

f=18000000 ± 90Hz

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: F, address: 1C, change the data and set the clock
frequency(f) to the specified value.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

Set the A/D value center of the microprocessor to the center voltage
of the zoom key.
If deviated, the zoom lens operates of itself ,even if the zoom key is
the center position.

Subject

Not required

Measurement Point

Display data of page: 6, address: 50

Measuring Instrument

Adjustment remote commander

Adjustment Page

F

Adjustment Address

5D

Don’t. touch the zoom lever during adjustment.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 6, address: 50, read the data, and this data is named
D

50

.

3)

Select page: F, address: 5D, set data: D

50

.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 0, address: 01, and set data: 00.

For detecting the position of the lens iris, adjust the hall AMP gain
and offset.

Subject

Not required

Measurement Point

Display data of page 1

Measuring Instrument

Adjustment remote commander

Adjustment Page

F

Adjustment Address

1E, 1F, 70

Specified Value

88 to 8C during IRIS OPEN
15 to 19 during IRIS CLOSE

Displayed data of page 1 of the adjustment remote commander.

1 : 00 : XX

Display data

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 6, address: 94, and set data: 8A.

3)

Select page: 6, address: 95, and set data: 17.

4)

Select page: 6, address: 01, set data: 6D, and press the PAUSE
button of the adjustment remote commander. (The HALL
adjustment is performed and the adjustment data is stored in
page: F, address: 1E, 1F and 70.)

5)

Select page: 6, address: 02, and check that the data is “01”.

6)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

Checking method:
1)

Select page: 6, address: 04, and set data: 03.

2)

Select page: 6, address: 01, set data: 01, and press the PAUSE
button.

3)

Select page: 1, and check that the display data (Note) during
IRIS OPEN satisfies the specified value.

4)

Select page: 6, address: 01, set data: 03, and press the PAUSE
button.

5)

Select page: 1, and check that the display data during IRIS
CLOSE satisfies the specified value.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Select page: 6, address: 04, and set data: 00.

3)

Select page: 6, address: 94, and set data: 00.

4)

Select page: 6, address: 95, and set data: 00.

5)

Select page: 0, address: 01, and set data: 00.

R285

IC207

IC202

25

36

37

48

1

12

13

24

5-20

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Subject

Siemens star chart with ND filter for
the minipattern box (Note1)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Adjustment Page

F

Adjustment Address

24 to 29, 36 to 3D, 5D

Specified Value

Upper digit: 0 to 9
Lower digit: 0 to 9

 Dark Siemens star chart.

NIGHT SHOT .................................................................. OFF

Preparations before adjustments:
The minipattern box is installed as shown in the following figure.

The attachment lenses are not used.

Specified voltage:

The specified voltage varies according to the
minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.

Adjusting method:
1)

Install the minipattern box so that the distance between it and
the front of the lens of the camcorder is less than 3cm.

2)

Make the height of the minipattern box and the camcorder equal.

3)

Check that the output voltage of the regulated power supply is
the specified voltage ± 0.01Vdc.

4)

Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposure
screen coincide.

5)

Select page: 0, address: 01, and set data: 01.

6)

Check that the data of page: F, address: 24 to 29, 36 to 3D is
the initial value (See table below).

7)

Select page: 6, address: 02, and check that the data is “00”.

8)

Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.

9)

Select page: 6, address: 01, set data: 27, and press the PAUSE
button.
(The adjustment data will be automatically input to page: F,
addresses: 24 to 29, 36 to 3D, 5D.)

10) Select page: 6, address: 02, and check that the data is “01”.
11) Select page: F, address: 3D, and check that the upper digit and

lower digit of the data satisfies each specified value.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Perform “Flange Back Check”.

24

25

26

27

28

29

36

51

19

22

20

93

13

00

37

38

39

3A

3B

3C

3D

00

46

00

19

00

2A

00

Minipattern box

Below 3 cm

Camcorder

Camera 

table

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

0.01Vdc

Output current : more than 3.5A

Fig. 5-1-6.

5-21

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Subject

Flange back adjustment chart
(2.0 m from the front of the lens)
(Luminance: 350 ± 50 lux)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Adjustment Page

F

Adjustment Address

24 to 29, 36 to 3D, 5D

Specified Value

Upper digit: 0 to 9
Lower digit: 0 to 9

NIGHT SHOT .................................................................. OFF

Adjusting method:
1)

Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and center
of the exposure screen coincide.

2)

Select page: 0, address: 01, and set data: 01.

3)

Check that the data of page: F, address: 24 to 29, 36 to 3D is
the initial value (See table below).

4)

Select page: 6, address: 02, and check that the data is “00”.

5)

Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.

6)

Select page: 6, address: 01, set data: 15, and press the PAUSE
button.
(The adjustment data will be automatically input to page: F,
addresses: 24 to 29, 36 to 3D, 5D.)

7)

Select page: 6, address: 02, and check that the data is “01”.

8)

Select page: F, address: 3D, and check that the upper digit and
lower digit of the data satisfies each specified value.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Perform “Flange Back Adjustment (2)”.

Perform this adjustment after performing “Flange Back Adjustment
(1)”.

Subject

Subject more than 500m away
(Subjects with clear contrast such as
buildings, etc.)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Adjustment Page

F

Adjustment Address

24 to 29, 36 to 3D, 5D

NIGHT SHOT .................................................................. OFF

Adjusting method:
1)

Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500 m away should
not be in the screen.)

2)

Select page: 0, address: 01, and set data: 01.

3)

Select page: 6, address: 02, and check that the data is “00”.

4)

Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.

5)

Place a ND filter on the lens so that the optimum image is
obtain.

6)

Select page: 6, address: 01, set data: 29, and press the PAUSE
button.
(The adjustment data will be automatically input to page: F,
addresses: 24 to 29, 36 to 3D, 5D.)

7)

Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Select page: 0, address: 01, and set data: 00.

3)

Perform “Flange Back Check”.

24

25

26

27

28

29

36

51

19

22

20

93

13

00

37

38

39

3A

3B

3C

3D

00

46

00

19

00

2A

00

5-22

Subject

Siemens star
(2.0m from the front of the lens)
(Luminance : approx. 200 lux)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Specified Value

Focused at the TELE end and WIDE
end.

Switch setting:
1)

NIGHT SHOT .................................................................. OFF

2)

DIGITAL ZOOM (Menu display) ................................... OFF

3)

STEADY SHOT (Menu display) ..................................... OFF

When the auto focus is ON, the lens can be checked if it is focused
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 6, address: 04, and set data: 0F.
2) Page 1 shows the state of the focus.

1 : 00 : XX

Odd: Focused
Even: Unfocused

Checking method:
1)

Place the Siemens star 2.0m from the front of the lens.

2)

To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.

3)

Shoot the Siemens star with the zoom TELE end.

4)

Turn on the auto focus.

5)

Check that the lens is focused (Note).

6)

Select page: 6, address: 21, and set data: 10.

7)

Shoot the Siemens star with the zoom WIDE end.

8)

Observe the TV monitor and check that the lens is focused.

Processing after Completing Adjustments:
1)

Select page: 6, address: 21, and set data: 00.

2)

Select page: 6, address: 04, and set data: 00.