DOWNLOAD Sony DCR-PC350 / DCR-PC350E (serv.man4) Service Manual ↓ Size: 1.82 MB | Pages: 74 in PDF or view online for FREE

6-22

DCR-PC350/PC350E

2. HALL Adjustment
For detecting the position of the lens iris and ND filter, adjust AMP
gain and offset.

Subject

Not required

Measurement Point

Display data of page 1 (Note1)

Measuring Instrument

Adjustment remote commander

Adjustment Page

F

19 (Note2)

Adjustment Address

13 to 18, 92

24 to 27

Specified Value 1

D6 to DA

Specified Value 2

26 to 2A

Specified Value 3

D3 to DD

Specified Value 4

23 to 2D

Note1: Displayed data of page 1 of the adjustment remote commander.

1 : XX : XX

IRIS display data
ND display data

Note2: When reading or writing the 19 page data, select page: 0, address:

10, and set data: 01, then select 9 page. The 19 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.

POWER ....................................................... CAMERA-TAPE

1

0

01

01

Set the data.

2

0

10

00

Set the data.

3

6

01

6D

Set the data, and press PAUSE
button.

4

6

02

Check that the data changes to
“01” within 50 sec. (Note3)

5

6

01

00

Set the data, and press PAUSE
button.

Note3: The adjustment data will be automatically input to page: F, address:

13 to 18, 92 and to page: 19, address: 24 to 27.

1

0

03

03

Set the data.

2

0

10

00

Set the data.

3

6

01

01

Set the data, and press PAUSE
button.

4

6

01

03

Set the data, and press PAUSE
button.

5

1

Check that the IRIS display data
(Note1) satisfies the specified
value 1.

6

6

01

01

Set the data, and press PAUSE
button.

7

1

Check that the IRIS display data
(Note1) satisfies the specified
value.2.

8

6

01

6B

Set the data, and press PAUSE
button.

9

6

01

69

Set the data, and press PAUSE
button.

10

1

Check that the ND display data
(Note1) satisfies the specified
value 3.

11

6

01

6B

Set the data, and press PAUSE
button.

12

1

Check that the ND display data
(Note1) satisfies the specified
value.4.

1

0

03

00

Set the data.

2

0

10

00

Set the data.

3

6

01

00

Set the data, and press PAUSE
button.

4

0

01

00

Set the data.

6-23

DCR-PC350/PC350E

3. MR Adjustment
The MR (Magnet resistor) adjustment of the inner focus lens is
carried out automatically. In whichever case, the focus will be
deviated during auto focusing/manual focusing.

Subject

Not required

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

58, 5A to 65

Specified Value1

40 to C0

Specified Value2

03 to 70

Specified Value3

90 to FD

Note1: Make the lens horizontal and perform this adjustment.
Note2: Perform this adjustment before “Flange Back Adjustment”.
Note3: The data of page: 0, address: 10 must be “00”.
Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:

6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER ....................................................... CAMERA-TAPE

1

0

01

01

Set the data.

2

6

01

BD

Set the data, and press PAUSE
button.

3

6

02

Check that the data changes to
“01”. (Note5)

4

F

5A

Check that the data satisfies the
specified value 1.

5

F

5B

Check that the data satisfies the
specified value 1.

6

F

5C

Check that the data satisfies the
specified value 1.

7

F

5D

Check that the data satisfies the
specified value 1.

8

F

5E

Check that the data satisfies the
specified value 2.

9

F

5F

Check that the data satisfies the
specified value 3.

10

F

60

Check that the data satisfies the
specified value 2.

11

F

61

Check that the data satisfies the
specified value 3.

12

F

62

Check that the data satisfies the
specified value 2.

13

F

63

Check that the data satisfies the
specified value 3.

14

F

64

Check that the data satisfies the
specified value 2.

15

F

65

Check that the data satisfies the
specified value 3.

Note5: The adjustment data will be automatically input to page: F, address:

58, 5A to 65.

1

6

01

00

Set the data, and press PAUSE
button.

2

0

01

00

Set the data.

3

Turn off the power and turn on
again

6-24

DCR-PC350/PC350E

4. CCD Output 2ch Matching Adjustment (1)
Correct the dispersion of the black level between the left-right
channels of the CCD imager.

Subject

Arbitrary

Adjustment Page

F

19 (Note3)

Adjustment Address

24 to 27

20 to 23, 2A to 2D

Note1: This adjustment should be carried out upon completion of the

following adjustments.

“HALL Adjustment”

Note2: After this adjustment, perform the following adjustments.

“CCD Output 2ch Matching Adjustment (2)”,  “Flange Back
Adjustment”, “Color Reproduction Adjustment”

Note3: When reading or writing the 19 page data, select page: 0, address:

10, and set data: 01, then select 9 page. The 19 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.

Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:

6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER ....................................................... CAMERA-TAPE

2)

NIGHT SHOT .................................................................. OFF

1

0

01

01

Set the data.

2

0

10

00

Set the data.

3

6

01

F3

Set the data, and press PAUSE
button.

4

6

02

Check that the data changes to
“01”. (Note4)

Note3: The adjustment data will be automatically input to page: F, address:

24 to 27 and to page: 19, address: 20 to 23, 2A to 2D.

1

0

10

00

Set the data.

2

6

01

00

Set the data, and press PAUSE
button.

3

Perform “CCD Output 2ch
Matching Adjustment (2)”.

5. CCD Output 2ch Matching Adjustment (2)
Correct the dispersion between the left-right channels of the CCD
imager.

Subject

Clear chart (All white) (Note1)

Adjustment Page

19 (Note2)

Adjustment Address

2E to 3F

Note1: Shoot the clear chart with the zoom TELE end.
Note2: This adjustment should be carried out upon completion of the

following adjustments.

CCD Output 2ch Matching adjustment (1)

Note3: When reading or writing the 19 page data, select page: 0, address:

10, and set data: 01, then select 9 page. The 19 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.

Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:

6, address: 01, set data: 00, and press the PAUSE button.

Switch setting:
1)

POWER ....................................................... CAMERA-TAPE

2)

NIGHT SHOT .................................................................. OFF

3)

ZOOM .................................................................... TELE end

1

0

01

01

Set the data.

2

0

10

00

Set the data.

3

6

2C

01

Set the data.

4

6

40

01

Set the data.

5

6

01

F5

Set the data, and press PAUSE
button.

6

6

02

Check that the data changes to
“01” in about 60 seconds after
pressing PAUSE button.

Note4: The adjustment data will be automatically input to page: 19,

address: 2E to 3F

1

0

10

00

Set the data.

2

6

01

00

Set the data, and press PAUSE
button.

3

6

2C

00

Set the data.

4

6

40

00

Set the data.

5

0

01

00

Set the data.

6-25

DCR-PC350/PC350E

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Subject

Flange back adjustment jig or
minipattern box (Siemens star chart
with ND filter (Note1))

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

48 to 58

Specified Value

Data of page: F, address: 57 is “00” to
“09”.
Data of page: 6, address: 0C is “00”.

Note1: Dark Siemens star chart.
Note2: This adjustment should be carried out upon completion of the

following adjustments.

“HALL Adjustment”, “MR Adjustment”,
“CCD Output 2ch Matching Adjustment”

Note3: Make the lens horizontal and perform this adjustment.
Note4: The data of page: 0, address: 10 must be “00”.
Note5: Check that the data of page: 6, address: 02 is “00”. If not, turn off

the power and turn on again.

Switch setting:
1)

POWER ....................................................... CAMERA-TAPE

2)

NIGHT SHOT .................................................................. OFF

3)

COLOR SLOW SHUTTER (CAMERA SET menu) ...... OFF

Preparations for the minipattern box:
1)

The minipattern box is installed as shown in the following
figure.

Note: The attachment lenses are not used.

2)

Install the minipattern box so that the distance between it and
the front of the lens of the camcorder is less than 3cm.

3)

Make the height of the minipattern box and the camcorder equal.

4)

Check that the output voltage of the regulated power supply is
the specified voltage.

5)

Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposure
screen coincide.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.

Fig. 6-1-9 (1).

Preparations for the flange back adjustment jig:
1)

Install the flange back adjustment jig so that the distance
between it and the front of the lens of the camcorder is less
than 3cm.

2)

Adjust the illumination intensity to the chart of the flange back
adjustment jig. (350 

±

 50 lux)

3)

Check that at both the zoom TELE end and WIDE end, the
center of the chart and center of the monitor TV screen coincide.

1

0

01

01

Set the data.

2

6

01

13

Set the data, and press PAUSE
button.

3

Wait for 2 sec.

4

6

01

27

Set the data, and press PAUSE
button.

5

6

02

Check that the data changes to
“01”. (Note6)

6

6

0C

Check that the data is “00”.

7

F

57

Check that the data is “00” to
“09”.

Note6: The adjustment data will be automatically input to page: F, address:

48 to 58.

1

6

01

00

Set the data, and press PAUSE
button.

2

6

01

25

Set the data, and press PAUSE
button.

3

6

01

00

Set the data, and press PAUSE
button.

4

0

01

00

Set the data.

5

Perform “Flange Back Check”.

±

Preparation of Flange Back Adj.
(Using the flange back adjustment jig)
(Luminance: about 300 lux)
1)

Install the flange back adjustment jig so that the distance be-
tween it and the front of lens of camera is less than 3 cm.

2)

Make the height of flange back adjustment jig and the camera
equal.

3)

Check that the center of chart meets the center of shot image
screen with the zoom lens at TELE end and WIDE end respec-
tively.

Flange back adjustment jig

Below 3 cm

Camera

Fig. 6-1-9 (2).