Sony DCR-PC350 / DCR-PC350E (serv.man4) Service Manual ▷ View online
6-2
DCR-PC350/PC350E
Replaced parts
Block replacement
Parts replacement
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z z
z
z z
z
z
z z
z
z
z
z
z z
z
z z
z z
z
z
z
z
Lens de
vice
Mechanism deck (Note1)
LCD block
LCD901 (LCD panel, touch panel)
LCD block
LED901 (Backlight)
EVF block
LCD902 (LCD panel)
Flash unit (FL7450)
Mechanism deck M901 (Drum assy) (Note1)
Mechanism MD block
CD-537 board
IC7302 (CCD imager)
CD-537 board
IC7303, X7301 (T
iming generator)
CD-537 board
IC7305 (S/H)
PD-225 board
IC602 (RGB dri
v
er
,
T
iming generator (LCD))
SE-151 board
D2501 (Backlight (EVF))
SE-151 board
SE2500/2501 (Y
A
W/PITCH sensor)
VC-370 board
IC1501 (,A/D con
v.
)
VC-370 board
IC2101 (Camera D
V
signal process, etc
.)
VC-370 board
IC2301 (D
V signal pr
ocess,RF signal pr
ocess)
VC-370 board
IC1801 (REC/PB
AMP)
VC-370 board
IC1901 (V
ideo IN/OUT)
VC-370 board
IC1650 (RGB dri
v
er
,
T
iming g
enerator (EVF))
1-1. Adjusting items when replacing main parts and boards.
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
When replacing main parts, adjust the items indicated by z in the following table.
Note1: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of Use check” of
“6-4. SERVICE MODE”)
Table. 6-1-1(1).
Adjustment
Section
Section
Initialization of
8, A, B, C, D, E, F,
14, 18, 19, 1A, 1B, 1C,
1E, 1F page data
8, A, B, C, D, E, F,
14, 18, 19, 1A, 1B, 1C,
1E, 1F page data
Camera
Color EVF
LCD
Mechanism
System control
Servo, RF
Video
Adjustment
Loading of flash memory program
Initialization of A, B, D, 1A,1B page data
Initialization of 8, C, 18, 1C page data
Initialization of E, F, 14, 19, 1E, 1F page data
54MHz/67.5MHz origin oscillation adjustment
HALL adj.
MR adj.
CCD Output 2ch Matching adj.
Flange back adj.
Mixed color compensation adj.
ND ON/OFF adj.
AWB standard data input
LV standard data input
Auto white balance adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj.
Steady shot check
Strobe light level adj.
Strobe white balance adj.
EVF automatic adj.
White balance adj.
LCD automatic adj.
V COM adj.
Transmissive mode white balance adj.
Reflective mode white balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
Error rate check
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Initialization of A, B, D, 1A,1B page data
Initialization of 8, C, 18, 1C page data
Initialization of E, F, 14, 19, 1E, 1F page data
54MHz/67.5MHz origin oscillation adjustment
HALL adj.
MR adj.
CCD Output 2ch Matching adj.
Flange back adj.
Mixed color compensation adj.
ND ON/OFF adj.
AWB standard data input
LV standard data input
Auto white balance adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj.
Steady shot check
Strobe light level adj.
Strobe white balance adj.
EVF automatic adj.
White balance adj.
LCD automatic adj.
V COM adj.
Transmissive mode white balance adj.
Reflective mode white balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
Error rate check
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
6-3
DCR-PC350/PC350E
CD-537 board
(COMPLEA
T)
PD-225 board
(COMPLEA
T)
SE-151 board
(COMPLEA
T)
VC-370 board
(COMPLEA
T)
VC-370 board
IC2602 (EEPR
OM)
VC-370 board
IC2701 (EEPR
OM)
Supporting
• Adjusting items when replacing a board or EEPROM
When replacing a board or EFPROM, adjust the items indicated by z in the following table.
When replacing a board or EFPROM, adjust the items indicated by z in the following table.
Table. 6-1-1(2).
Adjustment
Section
Section
Initialization of
8, A, B, C, D, E, F,
14, 18, 19, 1A, 1B, 1C,
1E, 1F page data
8, A, B, C, D, E, F,
14, 18, 19, 1A, 1B, 1C,
1E, 1F page data
Camera
Color EVF
LCD
Mechanism
System control
Servo, RF
Video
Adjustment
Loading of flash memory program
Initialization of A, B, D, 1A,1B page data
Initialization of 8, C, 18, 1C page data
Initialization of E, F, 14, 19, 1E, 1F page data
54MHz/67.5MHz origin oscillation adjustment
HALL adj.
MR adj.
CCD Output 2ch Matching adj.
Flange back adj.
Mixed color compensation adj.
ND ON/OFF adj.
AWB standard data input
LV standard data input
Auto white balance adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj.
Steady shot check
Strobe light level adj.
Strobe white balance adj.
EVF automatic adj.
White balance adj.
LCD automatic adj.
V COM adj.
Transmissive mode white balance adj.
Reflective mode white balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
Error rate check
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Initialization of A, B, D, 1A,1B page data
Initialization of 8, C, 18, 1C page data
Initialization of E, F, 14, 19, 1E, 1F page data
54MHz/67.5MHz origin oscillation adjustment
HALL adj.
MR adj.
CCD Output 2ch Matching adj.
Flange back adj.
Mixed color compensation adj.
ND ON/OFF adj.
AWB standard data input
LV standard data input
Auto white balance adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj.
Steady shot check
Strobe light level adj.
Strobe white balance adj.
EVF automatic adj.
White balance adj.
LCD automatic adj.
V COM adj.
Transmissive mode white balance adj.
Reflective mode white balance adj.
Tape path adj.
Touch panel adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
Error rate check
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Note2: When the repair is finished,
confirm the following items.
1. Shoot the all black subject (Attach
1. Shoot the all black subject (Attach
the lens cap and shoot), and confirm
that a vertical line is not displayed
in the center of the screen, and that
there is no difference in left-right
brightness level of the screen.
that a vertical line is not displayed
in the center of the screen, and that
there is no difference in left-right
brightness level of the screen.
2. Shoot a subject of low light, and
confirm that a vertical line is not
displayed in the center of the screen,
and that there is no difference in left-
right brightness level of the screen.
displayed in the center of the screen,
and that there is no difference in left-
right brightness level of the screen.
3. Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the screen,
and that there is no difference in left-
right brightness level of the screen.
When the above symptom
occurs, perform the whole process
of “CCD Output 2ch Matching
Adjustment”.
displayed in the center of the screen,
and that there is no difference in left-
right brightness level of the screen.
When the above symptom
occurs, perform the whole process
of “CCD Output 2ch Matching
Adjustment”.
Board
EEPROM
replacement replacement
z
z
z z
z z
z
z z
z z
z
z z
z
z
z z
z
z
z z
z
z
z z
z
z z
z
z
z z
z
z
z z
z
z
z z
z
z
z z
z
z
z z
z
z z
z
z z z
z
z z
z
z z
z
z z
z
z z z
z
z z
z
z
z z
z
z z
z
z z
z
z
z
z z
z z
z
z z
z
z z
z
z z
z z
6-4
DCR-PC350/PC350E
6-1. CAMERA SECTION ADJUSTMENT
1-1.
PREPARATIONS BEFORE ADJUSTMENT
1-1-1.
List of Service Tools
• Oscilloscope
• Color monitor
• Vectorscope
J-1
J-2
J-3
Filter for color
temperature
correction (C14)
J-6080-058-A
temperature
correction (C14)
J-6080-058-A
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
Pattern box PTB-450
J-6082-200-A
or
Pattern box PTB-1450
J-6082-557-A
J-6082-200-A
or
Pattern box PTB-1450
J-6082-557-A
Color chart for
pattern box
pattern box
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
Siemens star chart
J-6080-875-A
J-6080-875-A
Clear chart for
pattern box
pattern box
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
Mini pattern box
J-6082-353-B
J-6082-353-B
Adjustment remote
commander
(RM-95 upgraded)
J-6082-053-B
commander
(RM-95 upgraded)
J-6082-053-B
Camera table
J-6082-384-A
J-6082-384-A
Fig. 6-1-1.
Backgorund
paper
J-2501-130-A
paper
J-2501-130-A
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
J-13
J-14
CPC-6 flexible jig
J-6082-370-C
J-6082-370-C
CPC-6 terminal
board jig
J-6082-371-A
board jig
J-6082-371-A
Mixed color
compensation
chart
compensation
chart
For PTB-450:
J-6082-558-A
J-6082-558-A
For PTB-1450:
J-6082-561-A
J-6082-561-A
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
Ver 1.1 2004. 12
6-5
DCR-PC350/PC350E
1-1-2.
Preparations
Note1: For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
Note2: When performing only the adjustments, the lens block and boards
need not be disassembled.
Note3: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1)
Connect the equipment for adjustments according to Fig. 6-1-3.
Note4: As removing CN1020 of the VC-370 board means removing the
lithium 3V power supply (BT800 on the MS-234 board), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data.
But the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the lithium 3V power
supply is removed. (Refer to “6-4. Service Mode” for the self-
diagnosis data and the data on history of use.)
as date, time, user-set menus will be lost. After completing
adjustments, reset these data.
But the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the lithium 3V power
supply is removed. (Refer to “6-4. Service Mode” for the self-
diagnosis data and the data on history of use.)
Note5: Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 01, and press the PAUSE
2) Select page: A, address: 10, set data: 01, and press the PAUSE
button.
The above procedure will enable the camera power to be turned
on with the control switch block (PS7450) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
on with the control switch block (PS7450) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
Note6: Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 00, and press the PAUSE
2) Select page: A, address: 10, set data: 00, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.
Fig. 6-1-2.
1.5 m
Front of the lens
0.4m (PTB-1450)
1m (PTB-450)
1m (PTB-450)
Pattern box
Click on the first or last page to see other DCR-PC350 / DCR-PC350E (serv.man4) service manuals if exist.