Sony DCR-PC115E / DCR-PC120E Service Manual ▷ View online
— 17 —
DCR-PC115E/PC120E
2-8.
FLASH UNIT (MC)
1
Two screws
(M1.7
×
2.5),
lock ace, p2
1
Screw
(M1.7
×
2.5),
lock ace, p2
2
Mechanism deck,
MD frame assembly
3
EVF block assembly,
VF frame assembly
Flash unit (MC),
MC guard sheet
Flash unit (MC),
MC guard sheet
4
Flash unit (MC)
3
MC guard sheet
2
EVF block assembly,
VF frame assembly
2-9.
FLASH UNIT (ST)
2
7
1
Two screws
(M1.7
×
2.5),
lock ace, p2
5
ST cabinet upper
3
Precision screw
(dia, 1.7
×
4)
4
Three claws
6
Stroboscope
cushion (A)
1
Insulating sheet (ST)
4
Screw
(M1.7
×
2.5),
lock ace, p2
5
Screw
(M1.7
×
2.5),
lock ace, p2
3
Bolt
(M1.4
×
3)
6
Peel off the
adhesive side.
2
Hexagon hole
precision screw
7
Stroboscope assembly,
ST cabinet lower
8
Flash unit (ST)
— 18 —
DCR-PC115E/PC120E
The +P2 (0-No.) screws (M1.7
×
2.5) are MEC-processed. If the screws that are once removed,
are re-used, the screws may be loosened.
When re-assembling the mechanism, use the new +P2 (0-No.) screws (M1.7
When re-assembling the mechanism, use the new +P2 (0-No.) screws (M1.7
×
2.5).
Note:
2
Sheet (L)
7
Cabinet (G) assembly,
Control switch block
(FK-1850)
(FK-1850)
6
Claw
4
Two screws
(M1.7
×
2.5),
lock ace, p2
2
Screw
(M1.7
×
2.5),
lock ace, p2
5
Two screws
(M1.7
×
2.5),
lock ace, p2
3
Two screws
(M1.7
×
2.5),
lock ace, p2
3
Two screws
(M1.7
×
2.5),
0-No, +p2
(Note)
(Note)
1
Battery lock,
Compression spring
3
Cabinet (G)
assembly
1
Jack
cover (G)
4
Control switch block
(FK-1850)
4
Control switch block
(PS-1850) (15P)
2
Four precision
screws
(dia, 1.7
×
4)
1
Screw
(M1.7
×
2.5),
lock ace, p2
6
Cabinet (L),
Control switch block
(FK-1850)
(FK-1850)
5
G frame assembly,
Cabinet (rear) assembly,
Control switch block (PS-1850),
KY-060 board
Control switch block (PS-1850),
KY-060 board
Routing of the flexible board of the
Operation Control switch block (FK-1850)
when attaching the G frame assembly,
Cabinet (rear) assembly.
Operation Control switch block (FK-1850)
when attaching the G frame assembly,
Cabinet (rear) assembly.
2-10. CABINET (G) BLOCK ASSEMBLY, ETC.
— 19 —
DCR-PC115E/PC120E
2-11. CONTROL SWITCH BLOCK (FK-1850)
7
Two claws
q;
Speaker
9
Remove the
two solderings
5
Cabinet (L)
3
Two screws
(M1.7
×
2.5),
lock ace, p2
6
Two screws
(M1.7
×
2.5),
lock ace, p2
1
Four screws
(M1.7
×
2.5),
lock ace, p2
4
Precision screw
(dia, 1.7
×
4)
2
Precision screw
(dia, 1.7
×
4)
qa
Control switch block (FK-1850)
8
Jack frame assembly
2-12. CONTROL SWITCH BLOCK (PS-1850)
3
2
G frame assembly
1
Three precision
screws
(dia, 1.7
×
4)
6
Control switch block
(PS-1850) (7P)
8
Control switch block
(PS-1850)
5
Cabinet (rear)
assembly
7
KY-060 board
4
Two precision screws
(dia, 1.7
×
4)
— 20 —
DCR-PC115E/PC120E
2-13. BLIND PLATE ASSEMBLY
A
A
1
Four claws
If the FP-387 flexible board is
pulled in the direction of the
arrow
arrow
A
, the claws at the four
locations will be released.
Install the flexible wire to the blind plate
so that it covers the harness (PT-128).
so that it covers the harness (PT-128).
Remove the blind plate assembly
after opening the LCD panel.
after opening the LCD panel.
The +P2 (0-No.) screws (M1.7
×
2.5) are MEC-processed. If the screws that are once removed,
are re-used, the screws may be loosened.
When re-assembling the mechanism, use the new +P2 (0-No.) screws (M1.7
When re-assembling the mechanism, use the new +P2 (0-No.) screws (M1.7
×
2.5).
Note:
PRECAUTION DURING
FP-387 FLEXIBLE BOARD
INSTALLATION (1)
FP-387 FLEXIBLE BOARD
INSTALLATION (1)
2
FP-387 flexible board
Harness (PT-128)
Blind plate
assembly
assembly
2
Blind plate assembly
Remove it while taking care so that it must not
be caught by the flexible board and harnesses,
by pulling it in the direction of the arrow.
be caught by the flexible board and harnesses,
by pulling it in the direction of the arrow.
1
Two screws
(M1.7
×
2.5),
0-No, +p2
(Note)
(Note)
2-14. PD-148B BOARD, INVERTER TRANSFORMER UNIT
PD-148B
PD-148B
A
A
B
B
8
3
LCD cabinet (R)
assembly
5
Two screws
(M1.7
×
2.5),
lock ace, p2
4
Two screws
(M1.7
×
2.5),
MI
1
Two screws
(M1.7
×
2.5),
lock ace, p2
6
Two claws
2
Two claws
7
LCD cabinet (L)
assembly
2
Panel insulating
sheet
4
Remove the
three solderings
qa
Inverter transformer unit
5
Screw
(M1.7
×
2.5),
lock ace, p2
1
Harness
(PT-128) (16P)
9
PCB clip
8
PCB clip
q;
Remove the
six solderings
7
Back light
(Cold cathode fluorescent tube)
3
Liquid crystal
indicator module (24P)
6
Two claws
qs
PD-148B board
(Remove the FJ-035 board referring to section 2-3 before starting disassembling.)
Click on the first or last page to see other DCR-PC115E / DCR-PC120E service manuals if exist.