DOWNLOAD Sony DCR-PC115E / DCR-PC120E Service Manual ↓ Size: 5.31 MB | Pages: 86 in PDF or view online for FREE

— 9 —

• Follow the disassembly procedure in the numerical order given.
• Items marked “*” are not stocked since they are seldom required for routine service.

Some delay should be anticipated when ordering these items.

• The parts numbers of such as a cabinet are also appeared in this section.

Refer to the parts number mentioned below the name of parts to order.

The components identified by mark 

0

 or

dotted line with mark 

0

 are critical for safety.

Replace only with part number specified.

Jack ornamental cover assembly
X-3951-962-1

VF lens assembly
X-3951-894-1

Lens cap assembly
X-3949-944-1

Lens hood
3-063-515-01

Grip belt

Remote commander (RMT-811)
1-475-950-21

Battery case lid (for RMT-811)
3-053-056-01

Jack cover (G)
Note: Disassembling the main unit 

 is necessary to replace it.

Note: Disassembling the main unit 

 is necessary to replace it.

Lockace (M1.7)
3-057-437-01

Three screws 
(M1.7), lockace, P2
3-989-735-01

Screw 
(M1.7), lockace, P2
3-989-735-01

Screw 
(M1.7), lockace, P2
3-989-735-01

CPC lid
3-070-369-01

Battery cover
3-057-482-01

— 10 —

The following flow chart shows the disassembly procedure.

DCR-PC115E/PC120E

2-10. Cabinet (G) block assembly, etc

2-11. Control switch block (FK-1850)

2-12. Control switch block (PS-1850)

2-13. Blind plate assembly

2-14. PD-148B board,
         Inverter transformer unit

2-15. Hinge assembly

2-9. Flash unit (ST)

2-7. Mechanism deck

2-8. Flash unit (MC)

2-3. FJ-035 board

2-6. VC-270 board

2-4. VM-027 board

2-5. CD-349P board, Lens device

2-2.  VTR complete, Cabinet (R) section

2-1.  Cabinet (L) section

— 11 —

Attach the BT cable so 
that it stretches straight 
downward.

A

B 

1

  Pass the cable through the hole 

A

 of the 

      Cabinet (R) section.

2

  Draw the cable through clearance of the flexible

      board of the FJ-035 board and route it under the 
      flexible board of the FJ-035 board.

3

  Route the cable under the rigid portion of the 

      FJ-035 board.

4

  Insert it into the notch of the lens rubber (R).

5

  Insert it into the notch of the BT cable sheet.

6

  Route the cable through the clearance 

B

.

7

  Insert it to the connector on the BT-003 board.

BT cable

BT cable

BT cable

BT cable
guide

Lens 
rubber (R)

BT cable
sheet

BT-003 board

BT cable

Rigid portion of the
FJ-035 board

Flexible board of 
the FJ-035 board

Route the cable through the
clearance 

B

, and then hook

it on the clearance between 
the BT cable guide and 
lens device.

BT cable

BT cable
guide

Lens device 

BT-003 
board

Connector of 
BT cable

When removing the BT cable 
from the BT-003 board, be sure 
to hold the connector of the 
BT-003 cable and remove it.

— 12 —

NOTE: Follow the disassembly procedure in the numerical order given.

ON

OFF

When installing the Cabinet (L) section to the Cabinet (R) section 
and to the VTR complete, install it while the "Night-Shot switch 
outside the Cabinet (L) section" and "Night-Shot switch on top of 
the Lens Device" are facing upward.

1

 Screw 

     (M1.7 

×

 2.5), 

     lock ace, p2

3

 HS 

Cabinet

2

 Two claws

4

 Three screws 

     (M1.7 

×

 2.5), 

     lock ace, p2

5

 Jack ornamental 

     cover assembly

Jack ornamental 
cover assembly

Lens Device

Night-Shot switch on top of 
the Lens Device

Night-Shot switch outside the
Cabinet (L) section

3

 Two screws 

     (M1.7 

×

 4), 

     lock ace, p2

2

 Two screws 

     (M1.7 

×

 2.5), 

     lock ace, p2

4

 Screw 

     (M1.7 

×

 2.5), 

     lock ace, p2

1

 Screw 

     (M1.7 

×

 2.5), 

     lock ace, p2

6

 Cabinet (R) section, 

     VTR complete

5

 Control switch block 

     (FK-1850) (51P)

Flash unit (MC)

7

 Cabinet (L) section

Note: The power capacitor (C2010) of the flash unit is charged to the high tension voltage as high as 300 V at a maximum. 

You will get electrical shock when you touch the Flash unit (MC) mounted with the terminal of the charged capacitor. 
The charged potential remains even after the main power of the machine is turned off.
Discharge the remaining power in the capacitor referring to Service Note (page 6).

IR window 
assembly

Be careful that top of the Jack 
ornamental cover assembly does not 
hang over the IR window assembly.